Pixio PS1S Wave Premium Single Monitor Stand
Installation Guide
Please read the entire instruction manual before starting installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact your local distributor for assistance.
Safety and Important Information
CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.
Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
Safety gear and proper tools must be used. This product should only be installed by professionals.
Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact your place of purchase for a replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).
VESA Compatibility
The following table indicates the VESA screw and washer types compatible with your monitor.
Note: If using a monitor not manufactured by Pixio, confirm the VESA hole depth and use appropriately sized screws.
| Model | M-A (M4x12) | M-B (M4x16) | M-C (M5x12) | M-D (M5x16) | M-E (M6x12) | M-F (M6x16) |
|---|---|---|---|---|---|---|
| PX222 | • | |||||
| PX243 | • | |||||
| PX248 Prime | • | |||||
| PX248 Prime Advanced | • | |||||
| PX248 Prime S | • | |||||
| PX248 Pro | • | |||||
| PX248 Wave* | • | |||||
| PX257 Prime | • | |||||
| PX259 Prime | • | |||||
| PX259 Prime S | • | |||||
| PX273 | • | |||||
| PX273 Prime | • | |||||
| PX274 Prime | • | |||||
| PX277 Prime | • | |||||
| PX277 Prime Neo** | • | |||||
| PX277 Pro | • | |||||
| PX277 OLED Max | • | |||||
| PX278 | • | |||||
| PX278 Wave* | • | |||||
| PX279 Prime | • | |||||
| PX275C Prime | • | |||||
| PXC243S | • | |||||
| PXC273S* | • | |||||
| PXC277* | • | |||||
| PXC277 Advanced* | • | |||||
| PXC279* | • | |||||
| PXC325 | • | |||||
| PXC327 | • | |||||
| PXC327 Advanced | • | |||||
| PXC348C** | • |
* Please use the VESA standard conversion adapter included with the monitor.
** Please use the standoffs included with the monitor.
Parts List
| A | Arm A | (x1) |
| B | Arm B | (x1) |
| C | Clamp | (x1) |
| D | Bracket | (x1) |
| E | Fixing Plate | (x1) |
| F | Slit | (x1) |
| G | Bolt A | (x1) |
| H | Small Hex Wrench | (x1) |
| I | Large Hex Wrench | (x1) |
Installation Steps
Step 1: Attach the clamp to the desk surface.
Attach the clamp to the desk surface. The compatible desk surface thickness is 10-45mm.
Diagram Description: The clamp is shown being opened, placed onto a desk surface, with a slit inserted, and then tightened using the large hex wrench. For grommet mounting, the clamp is shown with its bolt removed, and a hole drilled in the desk surface, then secured with a fixing plate and slit.
Ensure the desk edge is at least 50mm away from the edge. The cable hole in the desk surface can also be used if it is within the specified range.
Step 2: Attach Arm B to the clamp.
Diagram Description: Arm B is shown being attached to the clamp mechanism.
Step 3: Attach Arm A to Arm B.
Diagram Description: Arm A is shown being attached to Arm B, with a small hex wrench used for tightening.
Step 4: Attach the bracket (D) to the back of the display.
Diagram Description: The bracket is shown being attached to the back of a monitor using screws. It illustrates correct screw length (M-A, M-B, M-C) and warns against using screws that are too long or too short.
CAUTION: Using bolts that are too long may damage the monitor. Using bolts that are too short may result in the monitor not being securely fixed and falling.
CAUTION: Be careful not to scratch or damage the display by placing a blanket underneath.
CAUTION: The weight of the display that can be attached is up to 9kg. Do not attach any other display.
Step 5: Attach the bracket to Arm A and close the lock on top of Arm A.
Diagram Description: The monitor bracket is shown being attached to Arm A. A knob is depicted, with arrows indicating vertical for unlock and horizontal for lock positions.
Turning the knob vertically unlocks it, and turning it horizontally locks it.
Step 6: Route cables through the cable holder.
Slide the cable holder downwards and out.
Step 7: Adjust the arm's spring tension to balance the monitor.
Level the arm as shown in the diagram.
If the arm lowers, turn the adjustment screw counter-clockwise to adjust to the horizontal position.
If the arm rises, turn the adjustment screw clockwise to adjust to the horizontal position.
Prohibited: Do not turn the screw on the back of Monitor Arm A. This can cause irreparable damage.
Note: This screw cannot be turned with the included wrench.
Note: If the display does not stay in the desired position, tighten the screw at the position shown in the diagram.
Step 8: Adjust the range of motion and stiffness of each part of the arm.
Diagram Description: Diagrams illustrate adjusting the arm's rotation limits (±90°, ±180°). Text explains how limiter screws control the range of motion. Another diagram shows the storage of hex wrenches in a slit on the arm.
Tightening the limiter screw inside the arm will limit the arm's movement to a 180° range.
Loosening or removing the limiter screw inside the arm will allow the arm to rotate 360°.
Store the large and small hex wrenches in the slit.
Specifications
VESA Compatibility: 75x75mm, 100x100mm
Screen Size Support: Up to 32 inches
Weight Capacity: 1-9kg (2.2-19.8lbs)
Usage: Indoor use only
Support and Information
For North America: www.pixiogaming.com
For Japan: www.pixiogaming.jp
For UK & EU: www.pixiogaming.co.uk
