Pixio PS2S WHITE Premium Single Monitor Stand

Important Safety Information

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.

Safety gear and proper tools must be used. This product should only be installed by professionals.

Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.

This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.

This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact your place of purchase for a replacement.

MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).

Product Overview

The Pixio PS2S WHITE is a premium single monitor stand designed for ergonomic viewing and efficient workspace setup.

VESA Compatibility

Supports VESA mounting patterns: 75x75mm and 100x100mm.

Weight Capacity:

• Flat Screens: 2.2 - 39.6 lbs (1 - 18kg)
• Curved Screens: 2.2 - 30.8 lbs (1 - 14kg)

Monitor Compatibility Chart

*Use VESA plate adapter that comes with the monitor.

Note: For non-Pixio brands, please check your monitor's VESA hole depth and use the proper screw size. For questions or comments, please contact Pixio at cs@pixiogaming.com.

Installation Instructions

The Pixio PS2S WHITE monitor stand can be installed using either a clamp mechanism or a grommet mount.

Clamp Installation

This method attaches the stand to the edge of a desk or table.

1. Assemble the desk clamp base: Connect the pole (B) to the base clamp part 1 (A), then attach the clamp arm (C) to the base clamp (A).
2. Insert the desk clamp screw (D) through the clamp arm (C) and into the base clamp (A). Adjust the screw to fit desk thicknesses ranging from 10mm to 45mm.
3. Place the pole cap (E) on top of the pole (B).
4. Slide the arm assembly (F) onto the pole (B).
5. Attach the VESA plate (G) to the back of your monitor using the appropriate screws (M-A, M-B, M-C, M-D, M-E, or M-F) and spacers if needed.
6. Mount the monitor with the attached VESA plate onto the arm assembly (F).
7. Secure the monitor using the locking knob (H).
8. The included Allen keys (I: 3mm, J: 6mm) are used for adjustments.

Grommet Installation

This method uses an existing hole in the desk for mounting.

1. Ensure your desk has a through-hole with a diameter between 10mm and 60mm.
2. Insert the grommet base (D) through the desk's through-hole.
3. Attach the pole assembly (B) to the grommet base (D).
4. Place the pole cap (E) on top of the pole (B).
5. Slide the arm assembly (F) onto the pole (B).
6. Attach the VESA plate (G) to the back of your monitor using the appropriate screws (M-A, M-B, M-C, M-D, M-E, or M-F) and spacers if needed.
7. Mount the monitor with the attached VESA plate onto the arm assembly (F).
8. Secure the monitor using the locking knob (H).
9. The included Allen keys (I: 3mm, J: 6mm) are used for adjustments.

Screw Types for Monitor Attachment:

• M-A: M4x12
• M-B: M4x16
• M-C: M5x12
• M-D: M5x16
• M-E: D5
• M-F: D5

Diagram Description: The installation diagrams visually guide users through attaching the base, pole, arm, and VESA plate. They show how to secure the stand to a desk edge (clamp) or through a desk hole (grommet), and how to attach the monitor. Key parts are labeled A through J, and screw types M-A through M-F are indicated for monitor attachment. Arrows show the direction of assembly or adjustment. Checkmarks (✔️) indicate correct parts or steps, while crosses (❌) indicate incorrect ones.

Arm Tension Adjustment

To properly balance the arm with monitors mounted, adjust the spring tension using the supplied Allen Key (part I or J):

1. First, position and firmly hold the arm horizontally. Assistance may be required.
2. If the arm drops: Turn the adjustment screw counter-clockwise until it stays in a horizontal position.
3. If the arm rises: Turn the adjustment screw clockwise until it stays in a horizontal position.

CAUTION: To avoid damage to monitors or mount, always keep the arm in a horizontal position while making adjustments. Assistance may be required.

Note: If the display does not stop at your desired position, tighten the limiting screws as shown in the diagram.

The arm can rotate 180° [circular arrow emoji] and can rotate without stopping (±180°).

Resources

For more information, visit Pixio websites:

North America | Japan | UK & EU