Best Choice Products 5-in-1 Outdoor Sport & Center Instruction Manual
Model: SKY6253
NOTICE
- Please retain these instructions for future reference.
- This product requires adult assembly and supervision when in use.
- Please read all instructions before attempting to install or assemble this item. Assembly should be done by adults only.
- Firmly secure all screws before use.
- Reconfirm that all bolts, screws, and knobs are secure before every use.
- Product is intended for outdoor use.
- If any parts are missing, broken, damaged, or worn, stop using this item until repairs are made and/or factory replacement parts are installed.
- Do not use this item in a way inconsistent with the manufacturer's instructions as this could void the product warranty.
- Assemble this product on a flat level surface near its intended space.
- This product is intended for residential use only.
WARNING
- Do not hang from the rim or climb on the pole. Do not climb on the base or structure in general, as this could result in serious injuries.
- Do not overtighten the hardware as this may damage the products structure.
- Adjustment and moving of the basketball set must be carried out by adults.
- The set requires two people for assembly.
Tools Required
- WRENCH (2, Provided)
- 14MM WRENCH (Not Provided)
- SCISSORS (Not Provided)
Intended for Ages: 8+
Assembly requires: 2 Persons
Estimated Assembly Time: Up to 75 Minutes
Hardware
| Item | Description | Quantity |
|---|---|---|
| 1 | Connector Knob | 1 PC |
| 2 | 8 x 50mm Bolt & Washer Set | 8 PCS |
| 3 | 8 x 30mm Bolt & Washer Set | 4 PCS |
| 4 | 8 x 15mm Bolt & Washer Set | 2 PCS |
| 5 | Net Bungie | 28 PCS |
| 6 | Net Rope | 2 PCS |
Parts
| Label | Description | Quantity |
|---|---|---|
| A | Right Rear Support | 1 PC |
| B | Left Rear Support | 1 PC |
| C | Right Corner (Large Net) | 1 PC |
| D | Left Corner (Large Net) | 4 PCS |
| E | Upper Bracing Rods | 1 SET |
| F | Upper Right Corner Support | 1 PC |
| G | Upper Left Corner Support | 1 PC |
| H | Connector Rod | 2 PCS |
| I | Small Net Top Support | 1 PC |
| J | Small Net Right Support | 1 PC |
| K | Small Net Left Support | 1 PC |
| L | Lower Bracing Rods | 1 SET |
| M | Small Net Bottom Support | 1 PC |
| N | Large Net Bottom Support | 1 PC |
| O | Basketball Pole | 1 PC |
| P | Backboard | 1 PC |
| Q | Basketball Hoop | 1 PC |
| Q1 | Basketball Hoop Net | 1 PC |
| R | Large Soccer Net | 1 PC |
| S | Small Net | 1 PC |
| S1 | Small Target Net | 1 PC |
| T | Storage Bag | 1 PC |
Product Assembly
Step 1
Connect the Part A right rear support to the Part C right corner. Repeat this process to connect the Part B left rear support to the Part D left corner.
Step 2
Connect the two corner assemblies using the Part N large soccer net bottom support.
Step 3
Locate and connect the Part F and Part G upper corner supports. Then, attach these upper corners to the Part A and Part B rear supports.
Step 4
Use the Part 6 net rope to attach the Part R large soccer net to the assembled large net frame (referencing steps 1-3). Drape the net over the frame to achieve the optimal shape. Thread the Part 6 net rope through the net ridge around the Part A or Part B corners and tie a knot. Continue threading the rope around the frame ridges and through the Part R soccer net. Tie a second knot to secure the net to the frame. Use scissors to cut away any excess rope.
Step 5
Locate and attach the Part I small net top support to the Part J and Part K side supports. Attach the Part M small net bottom support to the Part J and Part K side supports. Note: The Part I small net top support has a fastening hole in its upper receiver. This hole should face the back of the frame assembly.
Step 6
Use the Part 5 net bungies to attach one Part S1 small net to the small net frame assembly. (Note: Part S1 net is shown, but interchangeable with Part S small net). Drape the net over the frame. Take one bungie, loop the cord around the frame, and thread it through the net. Insert the end of the bungie back into its knot and pull until taught. Repeat with the remaining bungies until the net is completely secured.
Step 7
Insert two Part H connector rods into the Part F and Part G upper corners. Attach the assembled small net using four Part 2 screws (two screws per connector). Connect the Part M and Part N bottom supports as indicated. Assemble the basketball hoop next.
Step 8
Locate the Part Q basketball hoop frame and attach the Part Q1 basketball hoop net.
Step 9
Locate the Part O basketball pole and attach the Part P backboard and Part Q basketball hoop frame using four Part 3 bolt & washer sets.
Step 10
Attach two Part E bracing rods to the Part P backboard using two Part 4 bolt sets. Note: The bracing rods have two hole placements, one round and one slotted; attach the slotted end to the Part P backboard. Secure the Part O basketball pole to the Part P backboard by attaching two Part E bracing rods with one Part 2 bolt & washer set. Remove the washer for a tighter fit.
Step 11
Insert the Part O basketball pole into the opening on the Part I small net top support and secure with one Part 1 connector knob. Firmly twist the knob to secure the pole. Attach two Part L lower bracing rods to the Part O basketball pole with one Part 2 bolt & washer set. Remove the washer for a tighter fit. Attach the two Part L lower bracing rods to Part I small net top support with two Part 2 bolt and washer sets. Note: The bracing rods have two hole placements, one round and one slotted; attach the round end to the Part O basketball pole.
Step 12
Locate the Part T storage bag and unbutton the straps. Loop the straps around one of the Part H connector rods and button the straps to secure. RECOMMENDED: The Part O basketball pole may loosen after multiple impacts; check and tighten the Part 1 knob regularly.
Additional Information
Best Choice Products Rewards: Earn points while you shop. Join today! Give your friends 15% off their first order! For each successful referral, you'll receive 100 points. Visit bestchoiceproducts.com.
Help Center & Warranty
For questions about your product, visit help.bestchoiceproducts.com for Chat Support, Product Inquiry, Orders FAQ, Product Assembly, and Returns & Refunds.
Product Warranty Information
Items can be returned for any reason within 60 days of receipt for a full refund, provided they are in original packaging with all accessories. Refunds are issued to the original payment method. No re-stocking fee applies. A Return Authorization (RA) number is required, obtainable from a Best Choice Products Customer Service Representative. Items received without an RA may face delays or non-acceptance. Refunds/replacements are processed within 5 business days of receipt. Return shipping costs are the customer's responsibility unless the return is due to a Best Choice Products error, in which case a pre-paid shipping label will be provided. Original shipping boxes are not provided; customers must use them or purchase new ones. Pictures may be required for returns to verify item condition prior to return. All damages are the customer's responsibility until the item is received and acknowledged as undamaged by Best Choice Products.
WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, unapproved modification, or neglect of this product.
