Best Choice Products 3-Seat Converting Outdoor Swing
Instruction Manual
Ver. 5
As shoppers, we're always trying to find the perfect balance between quality & value. At BCP, we believe we've achieved that. Our diverse catalog of everyday essentials is tailored especially to our customers & guaranteed to hit that sweet spot of high quality & low price. Always.
❗ NOTICE
Please retain these instructions for future reference.
- Please do not exceed the weight limitations of this item.
- Do not stand on or use any part of this item as a step ladder.
- Firmly secure all bolts, screws and knobs before use.
- Reconfirm that all bolts, screws, and knobs are secure every 90 days.
- Fasten screws loosely during initial assembly. Do not firmly tighten the screws until the item is completely assembled.
- Be aware that some parts are heavy and have sharp edges.
- If any parts are missing, broken, damaged, or worn, stop using this product until repairs are made and/or factory replacement parts are installed.
- Do not use this item in a way inconsistent with the manufacturer's instructions as this could void the product warranty.
- This product is intended for residential use only.
Tools Required
Capacity & Assembly Information
Hardware
- Part 1: M8 x 100mm BOLT SET2 PCS
- Part 2: M8 x 95mm BOLT SET4 PCS
- Part 3: M8 x 75mm BOLT SET2 PCS
- Part 4: M6 x 60mm BOLT SET6 PCS
- Part 5: M6 x 40mm BOLT SET4 PCS
- Part 6: M6 x 35mm BOLT SET4 PCS
- Part 7: M6 x 32mm SCREW6 PCS
- Part 8: M6 x 30mm BOLT SET2 PCS
- Part 9: NUT CAP24 PCS
- Part 10: SPRING HOOK2 PCS
- Part 11: SPACER2 PCS
- Part 12: KNOB2 PCS
Parts
- Part A: TOP BAR1 PC
- Part B: FRONT LEG2 PCS
- Part C: BACK LEG2 PCS
- Part D: LEG SUPPORT2 PCS
- Part E: BACK SUPPORT1 PC
- Part F: MIDDLE SUPPORT1 PC
- Part G: FRONT SWING FRAME1 PC
- Part H: BACK SWING FRAME1 PC
- Part I: LEFT SEAT FRAME1 PC
- Part J: RIGHT SEAT FRAME1 PC
- Part K: SWING ARM4 PCS
- Part L: SEAT1 PC
- Part M: LOWER CANOPY FRAME2 PCS
- Part N: UPPER CANOPY FRAME2 PCS
- Part O: CANOPY1 PC
- Part P: CUSHION3 PCS
Product Assembly
Step 1
Insert a part B front leg into the part A top bar. Attach a part C back leg with a part 1 bolt set and two part 2 bolt sets. Repeat on the other side.
Place a part 9 nut cap on every nut.
Diagram Description: Shows the top bar (A) with a front leg (B) and a back leg (C) attached to each side using bolts (1, 2) and nut caps (9). The diagram indicates two bolts of type 1 and two bolts of type 2 are used per side, with six nut caps (9x6) shown in total.
Step 2
Attach a part D leg support and one side of the part E back support to the legs with three part 4 bolt sets. Repeat on the other side.
NOTE: The leg support and back support share a part 4 bolt set.
Attach the part F middle support with two part 8 bolt sets, one on each side.
Place a part 9 nut cap on every nut.
Diagram Description: Shows the partially assembled frame. Leg supports (D) and back supports (E) are attached to the legs using bolt sets (4). A middle support (F) is attached using bolt sets (8). The diagram indicates three bolt sets (4) are used for each leg support/back support assembly (total 4x6 shown), and two bolt sets (8) for the middle support. Eight nut caps (9x8) are shown.
Step 3
Attach the part I left seat frame to the part G front swing frame and part H back swing frame with two part 6 bolt sets. Repeat on the other side to attach the part J right seat frame.
Attach four part K swing arms with four part 5 bolt sets.
Secure the top of the swing arms with two part 10 spring hooks.
Diagram Description: Shows the lower frame assembly. Seat frames (I, J) are attached to the front (G) and back (H) swing frames using bolt sets (6). Swing arms (K) are attached using bolt sets (5). Spring hooks (10) are shown connecting the top of the swing arms. The diagram indicates four bolt sets (6x4) for the seat frames, four bolt sets (5x4) for the swing arms, and two spring hooks (10x2). Eight nut caps (9x8) are also shown.
Step 4
Insert the part L seat into the clamps on the back swing frame. Attach the seat with two part 3 bolt sets and two part 11 spacers.
Place a part 9 nut cap on every nut.
Diagram Description: Shows the seat (L) being attached to the back swing frame (H) using bolt sets (3) and spacers (11). A close-up view illustrates the connection point. Two bolt sets (3x2) and two spacers (11x2) are used. Two nut caps (9) are shown for securing.
Step 5
Hang the swing by inserting the spring hooks into the designated holes on the top bar.
Diagram Description: Shows the completed swing with the seat attached and the spring hooks (10) connected to the top bar, suspending the seat.
Step 6
Slide a part M lower canopy frame into the slots on the part O canopy. Within the canopy, attach a part N upper canopy frame with three part 7 screws. Repeat on the other side.
Secure the canopy to the swing with two part 12 knobs, one on each side.
Diagram Description: Shows the canopy assembly. Lower canopy frames (M) are inserted into the canopy (O). Upper canopy frames (N) are attached using screws (7). The completed canopy structure is then attached to the swing frame using knobs (12). The diagram indicates six screws (7x6) and two knobs (12x2) are used.
Step 7
Place three part P cushions.
Diagram Description: Shows the fully assembled swing with three cushions (P) placed on the seats.
Converting the Swing
Pull the seat up from the clamps on the back swing frame. Lay the seat flat while sliding the support arm into the designated slots on the rear of the swing.
Diagram Description: Illustrates the process of converting the swing to a flat bed. The seat is shown being lifted and then laid flat, with an arrow indicating the motion. A close-up shows the mechanism for securing the seat in its flat position.
Additional Information
Check out more great products: bestchoiceproducts.com
Earn points while you shop. Join today! bestchoiceproducts rewards. Join | Earn | Redeem
Give your friends 15% off their first order! For each successful referral you'll receive 100 points.
Visit bestchoiceproducts.com for more.
Help Center
Question about your product? We're here to help. Visit us at: help.bestchoiceproducts.com
Options available: Chat Support, Product Inquiry, Orders FAQ, Product Assembly, Returns & Refunds.
Product Warranty Information
All items can be returned for any reason within 60 days of the receipt and will receive a full refund as long as the item is returned in its original product packaging and all accessories from its original shipment are included. All returned items will receive a full refund back to the original payment method. All returned items will not be charged a re-stocking fee.
All returned items require an RA (Return Authorization) number, which can only be provided by a Best Choice Products Customer Service Representative when the return request is submitted. Items received without an RA may not be accepted or may increase your return processing time. Once an item has been received by Best Choice Products, refunds or replacements will be processed within 5 business days.
All returns must be shipped back to the Best Choice Products Return Center at the customer's expense. If the reason for return is a result of an error by Best Choice Products then Best Choice Products will provide a pre-paid shipping label via email. Boxes for return shipping will not be provided by Best Choice Products, and is the customer's responsibility to either use the original shipping boxes or purchase new boxes.
Pictures may be required for some returns to ensure an item is not damaged prior to its return. Items returned are not considered undamaged until they are received by Best Choice Products and verified as such. All damages to items are the customer's responsibility until the item has been received by and acknowledge by Best Choice Products as undamaged.
© 2023 Best Choice Products, Inc. All rights reserved. Distributed by Best Choice Products, Inc. Tustin, CA 92780
WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, unapproved modification, or neglect of this product.
Best Choice Products | Quality & Value, Always
