WINDHAM CORNER MEDIA STAND

Hardware Included

30 - large bolts

2 - small bolts

12 - medium screws

34 - wood dowels

2 - plates

2 - pulls

4 - shelf pins

2 - plastic anchors

2 - wall straps

2 - wall brackets

2 - wall brackets

2 - large screws

4 - small screws

Tools Required: Phillips head screwdriver

Missing hardware? Please call 800.606.6387 for replacements.

Components

2 - side panels (1 left, 1 right)

1 - center back panel

2 - back panels (1 left, 1 right)

1 - front frame

1 - top panel

1 - adjustable shelf

1 - bottom panel

Thank you for purchasing the Windham Corner Media Stand. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage. Note: 2 people are required to safely assemble this product.

Assembly Instructions

Step 1

A) Insert 6 wood dowels into the front frame as shown.

B) Fit dowels of the front frame into corresponding holes of the left and right side panels as shown. Attach side panels with 6 large bolts as shown. Secure bolts with a Phillips head screwdriver.

Step 2

A) Insert 2 wood dowels into the bottom panel as shown.

B) Fit dowels of the bottom panel into corresponding holes of the left back panel, and secure the left back panel with 2 large bolts as shown.

Step 3

A) Insert 2 wood dowels into the bottom panel as shown.

B) Fit dowels of the bottom panel into corresponding holes of the center back panel, and secure with 2 large bolts as shown.

Step 4

A) Insert 2 wood dowels into the bottom panel as shown.

B) Fit dowels of the bottom panel into corresponding holes of the right back panel, and secure with 2 large bolts as shown.

Step 5

A) Insert 8 wood dowels into the bottom panel as shown.

B) With the assistance of another adult, fit dowels of the bottom panel into corresponding holes of the front frame assembly. Secure the front frame assembly with 6 large bolts as shown.

Step 6

Insert 12 medium screws into the left and right back panels of the assembled unit as shown. Secure screws with a screwdriver.

Step 7

A) Insert 14 wood dowels into the top of the assembly as shown.

B) Fit the top panel onto corresponding dowels of the assembly. Secure from the inside with 12 large bolts as shown.

Step 8

A) Insert 4 shelf pins at desired shelf heights as shown.

B) Place the adjustable shelf into the assembled unit. Make sure each shelf pin is securely supported by each shelf pin.

Step 9

Attach 2 pulls and 2 plates to the doors of the assembled unit with 1 small bolt per pull as shown. Secure bolts with a screwdriver. Assembly is now complete.

Safety Mounting Instructions

For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is essential to use wall anchors appropriate to your wall type (i.e., plaster, drywall, concrete, etc.). Mount to wood studs whenever possible.

A) Attach anti-tip bracket to the top of the media stand using 2 small screws as shown.

B) Determine the final location of the media stand. Mark the position on the wall, approximately 2" below the anti-tip bracket mounted to the back of the media stand.

C) Drill a hole in the wall stud. If the wall stud is not available, drill a hole in the wall that is slightly smaller in diameter than the anchor. Gently tap the plastic anchor until the flange of the anchor is flush with the wall.

D) Attach the wall bracket to the wall by inserting 1 large screw through the wall bracket and into the wall anchor in the wall.

E) Place the unit so the anti-tip bracket on the back edge is aligned with the wall bracket.

F) Lace one end of the wall strap through both brackets, and into the other end of the strap.

G) Pull the strap tightly until secure.

Repeat steps A-G for the remaining anti-tip and wall bracket.

NOTE: If you are unsure about your wall type or what mounting method you should use, consult a qualified professional or your local hardware store.

Cleaning and Care

Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the wood is finished with a protective clear lacquer.