Emmer Desk with Power (60" / 153cm)

This document provides instructions for unpacking, assembling, and caring for your Emmer Desk with Power. Please take time to identify all hardware and components. For protection during assembly, place contents on a carpeted or padded area. Follow assembly instructions carefully to prevent personal or property damage.

Parts and Hardware Included

Main Components:

Desk Frame Component (Labeled A) (x1)
Desk Top Component (Labeled B) (x1)

Hardware:

Screws (x12)
Bolts (x4)
Washers (x16)
Allen Wrench (x1)
Power Strip Brackets (x2)
Power Strip Screws (x4)
Cable Clips (x2)
Wall Anchors (x2)
Wall Mounting Screws (x2)
Anti-Tip Straps (x1)
Plastic Ties (x2)

Tools Not Included:

Phillips Head Screwdriver
Drill
Level

Assembly Instructions

Step 1:

Attach the Desk Frame Component (A) to the Desk Top Component (B) using the provided screws and washers. Ensure all connections are snug.

Step 2:

Repeat Step 1 for the other side of the desk, connecting the second Desk Frame Component (A) to the Desk Top Component (B).

Step 3:

Install any necessary support beams or crossbars between the frame components as shown in the diagrams, using the provided bolts and washers.

Step 4:

Attach the power strip mounting brackets to the underside of the desk using the power strip screws.

Step 5: Repositioning the Power Strip

To change the position of the power strip, carefully detach it from its current location. Re-attach the power strip to the desired position using the appropriate mounting hardware and following the visual guide.

Important Note on Leveling [alert]

If the unit is not level, please follow the adjustment instructions provided in the diagrams to ensure stability.

Safety Warnings

WARNING: Furniture Tip-Over Hazard

Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over, install tip restraints per instructions. To further reduce the risk of serious injury and death from tip-overs:

Place heaviest items in the lowest compartments or drawers.
Unless specifically designed to accommodate, do not set TVs or other heavy objects on the top of this product.
Never allow children to climb or hang on drawers, doors or shelves.
Never open more than one drawer at a time.

Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over. For safe mounting, it is essential to use wall anchors appropriate to your wall type (e.g., plaster, drywall, concrete, etc). Mount to wood studs whenever possible. If you are unsure about your wall type or what mounting method you should use, consult a qualified professional or your local hardware store.

Wall Mounting Instructions

To securely attach the desk to the wall:

Step 1: Mark and Drill

Note the location of the product's mounting plates. Mark and drill holes on the wall for the mounting plates. Drill pilot holes into marked positions, preferably into a wall stud. If wall studs are not available, drill holes slightly smaller than the drywall anchors and insert each anchor until its flange is flush with the wall.

Step 2: Secure Brackets

Using a screwdriver, secure the mounting brackets to the wall stud or drywall anchors with the provided screws.

Step 3: Secure Desk

Position the desk in its final location. Secure it to the wall by lacing one end of a plastic tie through both the wall and product mounting plates, and then through the other end, pulling tightly to remove slack. Do not overtighten.

Cleaning and Care

To maintain your desk:

Clean surfaces with a dry or damp soft cloth.
Do not use abrasive cleaners.
Do not use furniture wax or polish.
It is recommended to use coasters to protect the surface from heat and water.
Do not leave spills unattended; clean them immediately.
Periodically check and tighten hardware as necessary.

	Rayna Headboard Assembly Instructions - Crate & Barrel Detailed assembly instructions and parts list for the Crate & Barrel Rayna Headboard, including cleaning and care guidelines. Learn how to assemble your Queen or King size headboard.
	Butterfly Wall Shelf Assembly Instructions and Care Guide Detailed instructions for assembling the Crate & Barrel Butterfly Wall Shelf, including safety precautions, parts list, mounting guidance, and cleaning recommendations. Available in English, French, and Spanish.
	Arden Headboard Assembly and Care Instructions - Queen/King Size Detailed assembly instructions and care guide for the Crate & Barrel Arden Headboard (Queen/King size). Includes parts list, assembly steps, and cleaning tips.
	Bardi Entryway Cabinet Assembly Instructions \| Crate & Barrel Detailed assembly instructions, safety warnings, and care guide for the Bardi Entryway Cabinet by Crate & Barrel. Learn how to assemble, mount, and maintain your furniture.
	Leisure Sectional Sofa Assembly and Safety Guide Assembly instructions and safety guidelines for the Leisure Sectional Sofa, including details on parts, assembly options, and power supply usage. Features information from Crate & Barrel.
	Arvada Headboard Assembly and Care Instructions - Crate & Barrel Detailed assembly instructions and care guide for the Crate & Barrel Arvada Headboard. Includes hardware list, component identification, and cleaning advice for optimal product care.
	Alfresco Dining Table Assembly Instructions Step-by-step assembly instructions for the Alfresco Dining Table from Crate & Barrel, including hardware, components, and care tips.
	JB Parchemin 80" Media Console Assembly and Safety Guide \| Crate & Barrel Detailed assembly instructions, safety warnings, and care guide for the JB Parchemin 80" Media Console from Crate & Barrel. Includes multilingual support and hardware identification.