AirFly SE - User Manual

Pairing AirFly with AirPods

Step 1: Prepare AirPods

To enter Pairing Mode on AirPods, first place AirPods inside the Charging Case. With the lid open, press and hold the button on the back of the Charging Case until the light flashes white.

[Diagram: Shows a wireless charging case and a standard charging case, with AirPods inside. A timer indicates 0:00:05.]

Step 2: Activate AirFly Pairing Mode

Turn AirFly on by sliding the ON/OFF switch up. The AirFly will automatically go into Pairing Mode the first time it is turned on, indicated by the flashing white and amber light.

[Diagram: Shows the AirFly device with '+' and '-' volume buttons and an ON/OFF switch. A close-up highlights the Reset Button and the ON/OFF Switch.]

Note: To re-pair or reset AirFly in the future, press and hold the Reset Button for four seconds to enter Pairing Mode. For easiest pairing, first turn off Bluetooth on any nearby devices - including your phone.

Step 3: Confirmation

Once successfully paired*, the light on the AirPods Charging Case will turn green and the light on AirFly will be solid white and turn off after 10 seconds.

[Diagram: Shows paired AirPods in their case and the AirFly device with a checkmark ✔️.]

* It can take up to 90 seconds for initial pairing, but AirFly will remember your AirPods when re-connecting in the future.

Step 4: Connect to Audio Source

Plug AirFly into any device with a standard headphone jack to listen to audio wirelessly.

[Diagram: Shows the AirFly device plugged into a headphone jack on an airplane seat entertainment screen.]

Pairing AirFly with Wireless Headphones

Step 1: Prepare Headphones

Put your headphones into Bluetooth Pairing Mode (refer to your headphones' owner's manual for more details).

[Diagram: Shows a pair of wireless headphones with a Bluetooth symbol ?.]

Step 2: Activate AirFly Pairing Mode

Turn AirFly on by sliding the ON/OFF switch up. The AirFly will automatically go into Pairing Mode the first time it is turned on, indicated by the flashing white and amber light.

[Diagram: Shows the AirFly device with '+' and '-' volume buttons and an ON/OFF switch. A close-up highlights the Reset Button and the ON/OFF Switch.]

Note: To re-pair or reset AirFly in the future, press and hold the Reset Button for four seconds to enter Pairing Mode. For easiest pairing, first turn off Bluetooth on any nearby devices - including your phone.

Step 3: Confirmation

Once successfully paired*, the light on AirFly will be solid white and turn off after 10 seconds.

[Diagram: Shows the AirFly device connected to headphones, with a checkmark ✔️.]

* It can take up to 90 seconds for initial pairing, but AirFly will remember your headphones when re-connecting in the future.

AirFly Volume Controls & Mute

To adjust the volume of AirFly, press Volume Buttons ('+' or '-'). You can also press and hold a Volume Button ('+' or '-') to gradually increase (or decrease) volume until its upper or lower limit is reached.

To MUTE AirFly audio temporarily, double-click the Volume Down Button. The light will blink amber continuously to let you know Volume is MUTED.

Double-click the Volume Down Button again to unmute audio and return to the previous volume setting.

[Diagram: Shows the AirFly device with '+' and '-' buttons, indicating volume adjustment and mute function. Arrows show up/down volume control.]

Battery Indicator

To check AirFly battery status, double-click the Volume Up button (+):

• 4 amber blinks = approx 100%
• 3 amber blinks = approx 75%
• 2 amber blinks = approx 50%
• 1 amber blink = approx 25%

[Diagram: Shows a hand pressing the '+' button on the AirFly device.]

Turning AirFly On & Off

Use the switch on the side of AirFly to turn it on or off.

Slide up to turn on. Slide down to turn off.

AirFly will reconnect to your headphones when turned back on.

[Diagram: Close-up of the ON/OFF switch on the AirFly device.]

Reconnecting Your AirPods or Headphones Back to Your Smartphone/Tablet

Once paired, AirFly will remember your AirPods / Headphones and switch to them when the unit is turned on. To switch back to using your AirPods / Headphones with your Smartphone or Tablet, first turn AirFly off.

On your device, open Bluetooth Settings, and select your headphones from the list. Status will change from 'Not Connected' to 'Connected' once headphones are successfully paired with your device.

[Diagram: Shows a smartphone displaying Bluetooth settings, with an arrow pointing to selecting 'AirPods / Headphones'.]

Charging AirFly

To charge, simply plug the included USB-C to USB-A Charging Cable into AirFly, and then into any powered USB port. AirFly is fully charged within 2 hours.

The internal battery of AirFly lasts about 20 hours. We recommend fully charging AirFly before using it for the first time. If your AirFly is low on power, it will flash amber 3 times every 10 seconds to alert you that it will need to be charged soon.

While charging, the AirFly will illuminate in amber and stay on. Once fully charged, the amber light will turn off. If desired, AirFly can remain plugged in and charging while in use.

[Diagram: Shows the AirFly device connected to a USB-C to USB-A cable, which is then plugged into a USB port.]

Tips & Tricks

1. If only one AirPod seems to be playing audio, turn AirFly off and back on. This will re-sync AirFly and should reconnect both AirPods.
2. If you want to pair a new set of headphones to AirFly, or are having trouble connecting to your headphones, reset AirFly by pressing and holding the Reset button on the side of AirFly for 4 seconds. Once reset, AirFly will blink amber 4 times, and then will go into Pairing Mode.

[Diagram: Shows a close-up of the Reset button on AirFly, with a timer indicating 0:00:04.]

Status Light Guide

Compliance and Safety Information

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

(French text also present in original document)

ISED Statement

This device complies contains license-exempt transmitter that comply with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

(French text also present in original document)

Safety Statement

Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;

Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;

A battery subjected to extremely low air pressure that may result in an explosion or the leakage.

(French text also present in original document)

NBTC Statement

This telecommunication equipment conforms to the requirements of the National Telecommunications Commission.

RED (Radio Equipment Directive)

Hereby, Twelve South, LLC, declare that the radio equipment type, Model number TS-2259, is in compliance with Directive 2014/53/EU. The full text of EU declaration of conformity is available at our website: http://www.twelvesouth.com

Frequency range: 2402 - 2480 MHz

Transmission power: <10 dBm(conducted)

Support and Recycling

Have questions? Visit twelvesouth.com or contact support@twelvesouth.com.

© 2024 Twelve South, LLC. All rights reserved. 1503 King St. Charleston, SC 29405 - USA

Recycle your electronics: twelvesouth.com/recycle

[Icons: French and English text with recycling symbols ♻️.]

Certifications: Bluetooth®, UK CA, CE, Energy Verified.

Model Number: CCA024LP0010T8