boAt Airdopes Ultra Plus - User Manual
Get ready to immerse yourself in music with your very own pair of boAt Airdopes Ultra Plus. This manual serves as your guide to unparalleled musical bliss. Knowledge of Bluetooth and device connectivity is essential.
Package Contains
- 1x Pair of TWS Earbuds
- 1x Charging Case
- 1x Type-C Charging Cable
- 2x Pairs of Extra Earmuffs (Small & Large)
- 1x User Manual
- 1x Warranty Card
- 1x Catalogue
- 1x FAQ Card
Power On
Smart Power On: Open the charging case lid with earbuds inside. They power on automatically via Insta Wake N' Pair™ technology, indicated by a blue LED flashing for 1 second and a voice prompt.
Manual Power On: Long touch the Capacitive Touch Control (CTC) on both earbuds for 3 seconds.
Upon powering on, earbuds enter connection mode, indicated by alternate red and blue LED flashes on the master earbud and blue LED flashes on the slave earbud.
Connection Mode
- Turn on Bluetooth on your phone/media device and scan.
- Select 'Airdopes Ultra Plus' from the list of available devices to pair.
Congratulations! Your earbuds are now connected successfully via Bluetooth, indicated by a solid blue LED light for 3 seconds.
Note: Pairing mode lasts for 5 minutes. Earbuds automatically reconnect to previously connected devices.
Single Earbud Usage (Mono Mode)
- Use Smart/Manual Power On for the desired earbud.
- The selected earbud enters pairing mode (red and blue LEDs flashing alternately).
- Turn on Bluetooth on your phone/media device and scan.
- Select 'Airdopes Ultra Plus' from the list of devices.
Note: To switch to Stereo mode, take out the other earbud. It will automatically power on and pair.
Controls in Mono Mode: Track skipping or returning to previous tracks is not possible.
Earbud Controls
- Answer/Hang Up Calls: Single tap CTC on either earbud.
- Reject Call: Double tap CTC on either earbud.
- Play/Pause Music: Single tap CTC on either earbud.
- Next Track: Double tap right earbud's CTC.
- Previous Track: Double tap left earbud's CTC.
- Activate Voice Assistant: Long touch left earbud's CTC for 3 seconds.
- Manual Power Off: Long touch both CTCs for 5 seconds.
Note: Volume can only be controlled via the media device.
BEAST™ Mode
Tap the left earbud CTC 3 times to switch to Low Latency gaming mode (BEAST™ Mode). This is notified via a sound prompt. Tap again 3 times to return to standard Music Mode.
BEAST™ Mode significantly reduces latency for an improved gaming experience.
ENx™ Tech
boAt's ENx™ (Environmental Noise Cancellation) technology cancels background noise for crystal clear voice calls. The 4x mics are equipped with this feature and activated by default, ensuring your voice is delivered without interruptions in noisy environments.
Charging
Charging the Earbuds
Place earbuds in the charging case in the correct orientation and close the lid. The case's white LED stays on for 5 seconds while charging and turns off when fully charged.
| Earbud State | Earbud LED Status |
|---|---|
| Low battery level (less than 20%) | 'Battery Low' prompt every 5 minutes. Red LED flashes 3 times every 30 seconds when case lid is opened. |
| 30%-100% battery level | Blue LED blinks 3 times when case lid is opened. |
| Earbuds are charging | Red LED stays ON for 2 seconds when case lid is opened and turns off when closed. |
| Earbuds are fully charged | Red LED turns OFF. |
Note: Fully charge earbuds before first use. Keep the case lid closed while charging. Earbuds cannot be switched on while charging.
Charging the Case
Plug one end of the provided USB Type-C cable into the case and connect the other end to a power source (computer, wall adapter, power bank).
| Charging Case Battery | LED Indication |
|---|---|
| Case is on charging | White LED blinks continuously. |
| Case gets fully charged | Solid white LED. |
Charging Norms & Precautionary Guidelines:
- Charger/Brick/Adapter: 5V 2A
- Cable/Wire: Standard Cable (35 strands @0.10mm diameter/strand)
Factory Reset
Perform a factory reset if you encounter operational difficulties. Clear 'Airdopes Ultra Plus' from your device's pairing history first.
- Open the charging case lid with earbuds inside.
- Long touch the reset button on the charging case for 10 seconds. Red LEDs on earbuds flash 5 times, and the white LED on the case blinks quickly 5 times.
- Close the case lid and wait 5 seconds.
- Take out earbuds and perform a fresh connection.
Your Airdopes Ultra Plus has now been reset.
Troubleshooting
| Potential Problem | Solution |
|---|---|
| If one earbud is not working | Perform the Factory Reset. |
| If earbuds are not in connection/scan mode | Perform the Factory Reset. |
| If earbuds disconnect during phone call | Charge the earbuds or perform the Factory Reset. |
| If there are other exceptions in usage | Place earbuds back into the charging case, try again, or perform Factory Reset. |
| If Touch Controls don't respond | Wipe the touch control area gently with a clean cloth to remove residual stains and perspiration. |
Safety Cautions
- Follow instructions for smooth operation.
- Avoid using earbuds in extreme temperatures.
- Do not use the product in water.
- Keep the product away from heat sources.
- Do not jam ports (charger port, LED port, etc.).
- It is recommended to use the product below maximum volume to protect hearing and extend service life.
Recommendation: Earbuds may start at 100% volume. Adjust to your preferred level using your phone/media device volume controls.
Specifications
| Headphone Type | TWS |
| Bluetooth Version | 5.3 |
| Music Playtime | Up to 50 hours (at 60% volume) |
| Number of ENx™ Equipped Mics | 4 |
| IWP™ Tech | Yes |
| BEAST™ Mode | Yes; 50 ms Low Latency |
| Transmission Range | 10 m |
| Driver Size | 10 mm*2 |
| Supported Codec | MP2, MP3, WMA, APE, FLAC, AAC, MP4, M4A, WAV, AIF, AIFC audio |
| Frequency | 20 Hz-20 kHz |
| Battery | 650 mAh (Case); 40 mAh*2 (Earbuds) |
| ASAP™ Charge | Yes; 5 mins charge = 60 mins playtime |
| Charging Time | 30 mins (Earbuds); Up to 15 hours (Case) |
| Charging Interface | USB Type-C |
| Water Resistance | IPX5 |
