OKIN REFINED System Instruction

Instruction of RF54

The document outlines the functions of the RF54 remote control for bedding systems.

Figure 1: Button layout of the remote.

The remote features buttons for massage control (HEAD, FOOT, TIMER/ALL OFF, ON/OFF, MASSAGE TYPE), memory positions (M1, M2), and bed movement (FLAT, HEAD UP, HEAD DOWN, FOOT UP, FOOT DOWN, ZG).

1.1 ZG button (button 10 in figure 1)

Clicking the ZG button moves the actuator to the ZG position and stops when any button is pressed during movement.

Pressing and holding the ZG button for 5 seconds records the current position as the ZG position, indicated by the timer LED flashing.

When moving to memory positions, the head and foot actuators move first, followed by the tilt and lumbar actuators.

1.2 M1 button (button 4 in figure 1)

Clicking the M1 button moves the actuator to the M1 position and stops when any button is pressed during movement.

1.3 M2 button (button 6 in figure 1)

Clicking the M2 button moves the actuator to the M2 position and stops when any button is pressed during movement.

1.4 Head up (button 7 in figure 1)

Pressing and holding the HEAD UP button moves the head actuator outwards. Movement stops when the button is released.

1.5 Head down (button 8 in figure 1)

Pressing and holding the HEAD DOWN button moves the head actuator inwards. Movement stops when the button is released.

1.6 Foot up (button 11 in figure 1)

Pressing and holding the FOOT UP button moves the foot actuator outwards. Movement stops when the button is released.

1.7 Foot down (button 12 in figure 1)

Pressing and holding the FOOT DOWN button moves the foot actuator inwards. Movement stops when the button is released.

When moving to the flat position, the lumbar and tilt actuators move first. After a 500ms delay, the head and foot actuators begin to move.

1.8 Flat (button 9 in figure 1)

Clicking the FLAT button flattens the bed. Movement stops when any button is pressed during the process.

1.9 Massage head (button 1 in figure 1)

Clicking the MASSAGE HEAD button cycles through massage intensity levels 0, 1, 2, and 3 for the head massage motor.

1.10 Massage FOOT (button 3 in figure 1)

Clicking the MASSAGE FOOT button cycles through massage intensity levels 0, 1, 2, and 3 for the foot massage motor.

1.11 Massage ON/OFF (button 2 in figure 1)

Clicking the Massage ON/OFF button toggles the massage motors between on and off states.

1.12 Massage Type (button 5 in figure 1)

Clicking the massage type button cycles through massage modes (type0, type1, type2, type3). This button only switches the massage mode and does not activate the motors.

FCC Warning

This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:

• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by:

• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and receiver.
• Connecting the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consulting the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC exposure compliance requirement, please follow operation instruction as documented in this manual.

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with ISED exposure compliance requirement, please follow operation instruction as documented in this manual.

Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé. Les utilisateurs finaux doivent suivre les instructions d'utilisation spécifiques pour satisfaire la conformité d'exposition RF. Pour maintenir la conformité aux exigences de conformité d'exposition ISED, veuillez suivre les instructions d'utilisation comme documenté dans ce manuel.

ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

• (1) this device may not cause interference, and
• (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes:

• (1) l'appareil ne doit pas produire de brouillage, et
• (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.