OKIN Refined Electric Technology Co., Ltd
Operating Manual of Remote Control System
Interface of the remote control
Model: RF.31.24.01 User Manual
2. Button Description
- A. HEAD UP button [⬆️]
- Press and hold the button, the Head actuator will move up, stop when released.
- B. HEAD DOWN button [⬇️]
- Press and hold the button, the Head actuator will move down, stop when released.
- C. FOOT UP button [⬆️]
- Press and hold the button, the Foot actuator will move up, stop when released.
- D. FOOT DOWN button [⬇️]
- Press and hold the button, the Foot actuator will move down, stop when released.
- E. HEAD&FOOT UP button [⬆️⬆️]
- Press and hold the button, the Head and Foot actuators will move up simultaneously, stop when released.
- F. HEAD&FOOT DOWN button [⬇️⬇️]
- Press and hold the button, the Head and Foot actuators will move down simultaneously, stop when released.
- G. TILT UP button [⬆️]
- Press and hold the button, the Tilt actuator will move up, stop when released. (Note: the Tilt actuator is a reversed actuator)
- H. TILT DOWN button [⬇️]
- Press and hold the button, the Tilt actuator will move down, stop when released. (Note: the Tilt actuator is a reversed actuator)
- I. NECK TILT UP button [⬆️]
- Press and hold the button, the Neck Tilt actuator will move up, stop when released.
- J. NECK TILT DOWN button [⬇️]
- Press and hold the button, the Neck Tilt actuator will move down, stop when released.
- K. ZERO GRAVITY button [⚖️]
- Click the button, Head and Foot actuators move to the preset Zero G position simultaneously, then Tilt and Neck Tilt actuators simultaneously move to the preset position and stop. (Note: the Tilt actuator is a reversed actuator), during movement, stopped by clicking any button (except flashlight button).
- L. ANTI SNORE button [?]
- Click the button, Head and Foot actuators move to preset ANTI SNORE position simultaneously, then Tilt and Neck Tilt actuators simultaneously move to the preset position and stop. (Note: the Tilt actuator is a reversed actuator), during movement, stopped by clicking any button (except flashlight button).
- M. FLAT button [↔️]
- Click the button, Tilt and Neck Tilt actuators move 500ms earlier than Head and Foot actuators. (Note: the Tilt actuator is a reversed actuator), actuators stop until move to flat position, during movement, stopped by clicking any button (except flashlight button).
- N. MEMORY A button [?️]
- Click the button, Head and Foot actuators move to preset MEMORY A position, then Tilt and Neck Tilt actuators move to preset position. (Note: the Tilt actuator is a reversed actuator), during movement, stopped by clicking any button (except flashlight button).
- O. MEMORY B button [?️]
- Click the button, Head and Foot actuators move to preset MEMORY B position, then Tilt and Neck Tilt actuators move to preset position. (Note: the Tilt actuator is a reversed actuator), during movement, stopped by clicking any button (except flashlight button).
- P. PRESET A button [?]
- Click the button, Head and Foot actuators move to PRESET A position, then Tilt and Neck Tilt actuators move to preset position. (Note: the Tilt actuator is a reversed actuator), during movement, stopped by clicking any button (except flashlight button).
- Q. PRE-SET NECK TILT button [?]
- Click the button, the Neck Tilt actuator will move and keep running until it arrives at the Memory position preset by user, during movement, stopped by clicking any button (except flashlight button).
The blue LEDs for backlight are on as long as any button is pressed. The backlight LED will turn off automatically after 5s when all buttons are released.
The following positions can be changed or set by the user: The Zero gravity position; The Memory A position; The Memory B position; The ANTI SNORE position; The PRESET position; The PRE-SET NECK TILT position.
Procedure to Set Special Positions
- Click the [↔️] button to flat the bed;
- Adjust the actuators to a desired position by pressing the button HEAD_UP, HEAD_DOWN, FOOT_UP, FOOT_DOWN, TILT_UP, TILT_DOWN, NECK TILT_UP, or NECK TILT_DOWN;
- Press and hold any one button of ZG [⚖️], MEMORY A [?️], MEMORY B [?️], ANTI SNORE [?], PRESET A [?], or PRE-SET NECK TILT [?] for 5s. The backlight LED starts flashing, which indicates that memory position setting has been finished.
Zero G position, MEMORY A, MEMORY B, ANTI SNORE, PRESET A, and PRE-SET NECK TILT positions can all be reset to default settings: press and hold FLAT [↔️] + ZG [⚖️] for about 5s, until the backlight LED starts flashing.
More Button Descriptions
- R. FLASHLIGHT button [?]
- Click the button, the Flashlight on the remote control will turn on (if it is being off) or turn off (if it is being on). If the Flashlight is turning on as the button is pressed, it will keep on as long as the button is pressed. When the button is released, the Flashlight will still keep on for several seconds then turn off simultaneously with the backlight LED.
- S. UNDERLIGHT button [?]
- Click the button, the under bed light will turn on (if it is being off) or turn off (if it is being on). If the under bed light is turning on as the button is pressed, it will keep on for 5 minutes then turn off automatically if the button isn't pressed again.
- T. Massage INTENSITY HIGHER button [➕]
- Click the button, the vibrating intensity will raise up by one level, total 3 levels; when it reaches the third level, click the button again, turn off the massage motors.
- U. Massage INTENSITY LOWER button [➖]
- Click the button, the vibrating intensity will lower down by one level, total 3 levels; when it reaches the third level, click the button again, turn off the massage motors.
- V. Massage MODE INCREASEMENT button [▶️]
- If the vibrating has started up, click the button, the vibrating mode will raise up by one level, total 4 levels.
- W. Massage SPEED DECREASEMENT button [◀️]
- If the vibrating has started up, click the button, the vibrating speed will lower down by one level, total 4 levels.
Note: If the vibration motors are stopped, press any one button of [➕] or [▶️] to turn on the vibration motor. The vibrator intensity is the first level, the vibration mode remains the one before stop.
- X. Massage time button [⏱️]
- Click the button to stop all movements of actuators. When the actuators are in idle state and the massage motors are working, press this button to cycle change the vibration time. Vibration time is the time duration that keeps vibrating. If no button is pressed (relating to vibration), it will stop automatically when it reaches the time. The time and the LED indication are as below:
- 10MIN: This LED flashes once [?], the vibrating time is 10 minutes;
- 20MIN: This LED flashes once [?], the vibrating time is 20 minutes;
- 30MIN: This LED flashes once [?], the vibrating time is 30 minutes;
Note: 10min, 20min, 30min LED flashes once, the corresponding vibration time respectively is 10 minutes, 20 minutes, 30 minutes. As the vibration time changes, the LED will adjust accordingly.
System Diagram and Components
The system diagram illustrates the connectivity of the OKIN remote control system. It shows the 22-key remote control (RF.31.24.01) connected to a control box (CB.13.42.01). The control box is linked to various components including a Head Motor (B.15055), Foot Motor (B.11964), Lumbar Motor (JLDQ.16.263.84), Tilt Motor (JLDQ.16.228.31), and Massage Motors (JLDQ.9.001.130C). Power is supplied via a Power Supply (JLDP.10.023.000) and connected through a Power Cord AC (R5.504.01.250) and a cord of Power (R5.217.01.016). Other connections include a Y-Cable (R5.216.01.015C), patch cords for LED strips/LED (R5.413.01.005), underbed lighting/LED (R5.113.00.011), and USB charging components like USB Charger/USB (JLDP.05.032.000) and Double USB socket (JLDP.14.027.000).
| NO. | Product Name | Product Code | Quantity |
|---|---|---|---|
| 1 | Head Motor | B.15055 | 1 |
| 2 | Foot Motor | B.11964 | 1 |
| 3 | Lumbar Motor | JLDQ.16.263.84 | 1 |
| 4 | Tilt Motor | JLDQ.16.228.31 | 1 |
| 5 | Massage Motor | JLDQ.9.001.130C | 2 |
| 6 | Massage Motor Cable | R5.410.01.009 | 1 |
| 7 | Control Box | CB.13.42.01 | 1 |
| 8 | Power Supply | JLDP.10.023.000 | 1 |
| 9 | Cord of Power | R5.217.01.016 | 1 |
| 10 | Power Cord AC | R5.504.01.250 | 1 |
| 11 | Y-Cable | R5.216.01.015C | 1 |
| 12 | Patch cord of LED strip/LED | R5.413.01.005 | 1 |
| 13 | Underbed lighting /LED | R5.113.00.011 | 1 |
| 14 | USB Charger/USB | JLDP.05.032.000 | 1 |
| 15 | Double USB socket | JLDP.14.027.000 | 2 |
| 16 | 22keys Remote Model/22 | RF.31.24.01 | 1 |
Regulatory Information
FCC Compliance
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ISED RSS Warning
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
