Shelly Dimmer 0/1-10V PM Gen3

Safety Information

⚠ WARNING! Risk of electric shock.

Installation of the Device to the power grid must be performed carefully by a qualified electrician.

⚠ CAUTION! Before installing the Device, turn the circuit breakers off.

Use a suitable test device to make sure there is no voltage on the wires you want to connect. When you are sure that there is no voltage, proceed to the installation.

⚠ WARNING! Before making any changes to the connections, ensure there is no voltage present at the Device terminals.

⚠ CAUTION! Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.

⚠ CAUTION! Connect the Device only to a power grid and appliances that comply with all applicable regulations. A short circuit in the power grid or any appliance connected to the Device can cause fire, property damage, and electric shock.

⚠ CAUTION! The Device must be secured by a cable protection switch in accordance with EN60898-1 (tripping characteristic B or C, max. 16A rated current, min. 6 kA interrupting rating, energy limiting class 3).

⚠ CAUTION! Do not use the Device if it shows any sign of damage or defect.

⚠ CAUTION! The Device may be connected to and control only electric circuits and appliances that comply with the applicable standards and safety norms.

⚠ CAUTION! The Device is intended only for indoor use.

⚠ CAUTION! Keep the Device away from dirt and moisture.

Product Description

The Shelly Dimmer 0/1-10V PM Gen3 is a smart dimming controller that allows remote control of dimming drivers from a mobile phone, tablet, PC, or home automation system. It can work standalone in a local Wi-Fi network or be operated through cloud home automation services. The device supports 0-10V and 1-10V types of drivers.

The Device features an embedded web interface for monitoring, control, and adjustment. The web interface is accessible at http://192.168.33.1 when connected directly to the Device access point, or at its IP address when connected to the same network.

The Device can interact with other smart devices or automation systems within the same network infrastructure. Shelly Europe Ltd. provides APIs for device integration and cloud control. More information is available at https://shelly-api-docs.shelly.cloud.

ⓘ The Device comes with factory-installed firmware. Shelly Europe Ltd. provides free firmware updates to keep it updated and secure. Installation of firmware updates is the user’s responsibility. Shelly Europe Ltd. is not liable for any lack of conformity caused by failure to install updates promptly.

Installation Instructions

ⓘ For connecting the Device, solid single-core wires or stranded wires with ferrules are recommended. Wires should have insulation with increased heat resistance, not less than PVC T105°C (221°F).

ⓘ When connecting wires, consider the specified conductor cross-section and stripped length. Do not connect multiple wires into a single terminal.

ⓘ For security reasons, after successfully connecting to the local Wi-Fi network, it is recommended to disable or password-protect the Device AP (Access Point).

ⓘ To perform a factory reset, press and hold the Control button for 10 seconds.

ⓘ To enable the access point and Bluetooth connection, press and hold the Control button for 5 seconds.

Wiring Diagram Description

The wiring diagram illustrates the connections for the Shelly Dimmer 0/1-10V PM Gen3. The device terminals are connected as follows:

• Device positive output (+) connects to LED driver positive input (Dim+).
• Device negative output (-) connects to LED driver negative input (Dim-).
• Live wire connects to Device L terminal.
• Neutral wire connects to Device N terminal and to the LED driver N terminal.
• Device relay output O connects to the LED driver L terminal.
• Switches or buttons connect to Device S1 and S2 terminals and the Live wire.

The Device supports single-button, dual-button, or single-switch modes. In single input mode, S2 is always detached.

Connect the LED driver to the LED lights according to the LED driver manufacturer's instructions.

Specifications

Wi-Fi

• Protocol: 802.11 b/g/n
• RF band: 2401-2495 MHz
• Max. RF power: < 20 dBm
• Range: Up to 30 m / 100 ft indoors and up to 50 m / 160 ft outdoors (depending on local conditions)

Bluetooth

• Protocol: 4.2
• RF band: 2400-2483.5 MHz
• Max. RF power: < 4 dBm
• Range: Up to 30 m / 100 ft outdoors, up to 10 m / 33 ft indoors (depending on local conditions)

CPU & Memory

• CPU: ESP-Shelly-C38F
• Clock frequency: 40 Mhz
• Flash: 8MB

Features

• Schedules: 20
• Webhooks (URL actions): 20 with 5 URLs per hook
• Scripting: Yes
• MQTT: Yes
• Advanced schedules: Yes
• KVS (Key-Value Store): Yes

Shelly Cloud Inclusion

The Device can be monitored, controlled, and set up through the Shelly Cloud home automation service via Android, iOS, or Harmony OS mobile applications, or any internet browser at https://control.shelly.cloud/. For detailed instructions on connecting and controlling the Device with the Shelly app, refer to the application guide: https://shelly.link/app-guide.

The Shelly mobile application and Shelly Cloud service are not required for the Device to function properly. The Device can be used standalone or with other home automation platforms.

Troubleshooting

For installation or operation problems, consult the knowledge base page: https://shelly.link/dimmer_0/1-10V_PM_Gen3

Declaration of Conformity

Shelly Europe Ltd. declares that the radio equipment type Shelly Dimmer 0/1-10V PM Gen3 complies with Directive 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The full text of the EU declaration of conformity is available at: https://shelly.link/dimmer_0/1-10V_PM_Gen3_DoC

Manufacturer Information

Manufacturer: Shelly Europe Ltd.

Address: 103 Cherni vrah Blvd., 1407 Sofia, Bulgaria

Tel: +359 2 988 7435

E-mail: support@shelly.cloud

Official website: https://www.shelly.com

Changes in contact information are published by the Manufacturer on the official website.

All rights to the trademark Shelly® and other intellectual rights associated with this Device belong to Shelly Europe Ltd.