Assembly Instructions

Part List

Hardware List

Assembly Tools Required (Not Included): Screwdriver (not specified type, but implied Phillips head from screw drawings).

Warning: Please be careful not to damage the hole position when using power tools. [!]

Assembly Instructions

Step 1:

Connect the HB/FB horizontal pieces (A) to the side panels (B) and legs (C, D). Use hardware 3 (Hex-Head bolts, 8pcs) and hardware 6 (Horizontal-Hole bolts, 8pcs). A diagram shows two horizontal pieces (A) being attached to a side panel (B) and a leg (C/D). The note indicates that part 6 should be oriented with the 'x' mark facing up for proper tightening.

Diagram Description: Two horizontal frame pieces (A) are shown being attached to a vertical leg piece (C or D) and a side panel (B). Bolts (3) and horizontal-hole bolts (6) are used. A close-up shows the orientation of part 6.

Step 2:

Attach drawer stoppers (8) to the front side rail (B) using screws (10). The diagram shows two stoppers (8) being affixed to the inner side of the front rail (B) with screws (10).

Diagram Description: Two drawer stoppers (8) are attached to the inner surface of the front side rail (B) using screws (10). The diagram indicates 6 pieces of screw (10) are used for this step, along with 3 pieces of part 8.

Step 3:

Attach trundle stoppers (8) to the back side rail (A) using screws (10). The diagram shows two stoppers (8) being affixed to the inner side of the back rail (A) with screws (10).

Diagram Description: Two drawer stoppers (8) are attached to the inner surface of the back side rail (A) using screws (10). The diagram indicates 4 pieces of screw (10) are used for this step, along with 2 pieces of part 8.

Step 4:

Attach legs (C, D) to the side rails (A, B). Use hardware 2 (Hex-Head bolts, 8pcs). The diagram shows legs being attached to the corners of the bed frame structure.

Diagram Description: Legs (C and D) are attached to the ends of the side rails (A and B) using bolts (2). The Allen key (5) is shown for tightening.

Step 5:

Assemble the main bed frame. Connect the side rails (A, B) and headboard/footboard (C, D) using hardware 2 (Hex-Head bolts, 8pcs) and hardware 6 (Horizontal-Hole bolts, 8pcs). The diagram shows the main bed frame structure coming together.

Diagram Description: The main bed frame is assembled by connecting the side rails (A, B) to the headboard/footboard components (C, D) using bolts (2) and horizontal-hole bolts (6). An exploded view shows the connection points.

Step 6:

Install the bed slats (F) onto the side rails. Use hardware 10 (Wood screws, 12pcs). The diagram shows slats being screwed into place along the length of the side rails.

Diagram Description: The bed slats (F) are attached to the inner ledges of the side rails (A, B) using screws (10). A note specifies to leave a small gap at the edges of the outermost slats to prevent breakage.

Step 7:

Begin assembling the drawers. Connect the drawer front (G) to the drawer sides (J). Use hardware 1 (Wood dowels, 8pcs) and hardware 4 (Hex-Head bolts, 4pcs) and hardware 6 (Horizontal-Hole bolts, 4pcs).

Diagram Description: The drawer front (G) is joined to the drawer side pieces (J). Dowels (1) are inserted into holes, and then bolts (4) and horizontal-hole bolts (6) are used to secure the connection. This step is repeated twice (x 2).

Step 8:

Attach the drawer back (H) to the drawer sides (J) and insert the drawer bottom (K). Use hardware 1 (Wood dowels, 16pcs) and hardware 4 (Hex-Head bolts, 4pcs) and hardware 6 (Horizontal-Hole bolts, 4pcs). The diagram shows the drawer box being completed.

Diagram Description: The drawer back (H) is attached to the drawer sides (J) using dowels (1) and bolts (4, 6). The drawer bottom (K) is slid into grooves and secured. This step is repeated twice (x 2).

Step 9:

Attach drawer runners (7) to the assembled drawers. Use hardware 9 (Wood dowels, 8pcs) and hardware 10 (Wood screws, 16pcs). The diagram shows the runners being attached to the bottom edges of the drawers.

Diagram Description: Drawer runners (7) are attached to the bottom outer edges of the assembled drawers. Screws (10) are used for attachment. This step is repeated twice (x 2).

Step 10:

Attach wheels (11) to the drawer bottoms (K). Use hardware 10 (Wood screws, 4pcs). The diagram shows wheels being attached to the underside of the drawer bottoms.

Diagram Description: Wheels (11) are attached to the underside of the drawer bottoms (K) using screws (10). This step is repeated twice (x 2).

Step 11:

Install the assembled drawers into the main bed frame. The diagram shows the drawers being slid into place.

Diagram Description: The completed drawers are slid into the designated compartments under the main bed frame.

Step 12:

Attach metal brackets (12) to the bed frame. Use hardware 14 (Wood screws, 8pcs). The diagram shows brackets being attached to the frame.

Diagram Description: Metal brackets (12) are attached to the bed frame using screws (14). This step is repeated twice (x 2).

Step 13:

Attach metal brackets (13) to the bed frame. Use hardware 14 (Wood screws, 2pcs). The diagram shows brackets being attached to the frame.

Diagram Description: Metal brackets (13) are attached to the bed frame using screws (14). This step is repeated twice (x 2).

Step 14:

Push the assembled drawers and trundle under the bottom of the full bed. The diagram shows the final placement of the drawers and trundle.

Diagram Description: The assembled drawers and the trundle unit are pushed into their final positions under the main bed frame.