Aminalife Wall Bed Assembly Instructions

General Information

Assembly Requirement: Four people are required to assemble and move this model. ?‍?‍?‍?

Mattress Note: This bed must be equipped with a mattress equivalent to 44 lb.

Part Lists

Box 1 - N708P299596

• A5: Panel - 1pc
• A6: Panel - 1pc
• A9: Panel - 2pcs
• C5: Panel - 7pcs
• C7: WoodBar - 2pcs
• D2: Slats - 3pcs
• D3: Slats - 2pcs
• D7: Panel - 2pcs
• D8: Metal corner link - 1pc
• D9: Metal corner link - 1pc
• E1: Metal corner link - 2pcs
• E3: Panel - 1pc

Box 2 - N708P299597

• B1: WoodBar - 2pcs
• B2: Panel - 1pc
• B3: WoodBar - 1pc
• B4: Panel - 1pc
• C4: WoodBar - 4pcs
• C8: WoodBar - 2pcs
• D4: WoodBar - 2pcs
• D5: WoodBar - 2pcs
• D6: WoodBar - 1pc

Box 3 - N708P299598

• A1, A2, A3, A4: Leg - 1pc each
• A7, A8: WoodBar - 2pcs each
• B9: WoodBar - 2pcs
• C1, C2: WoodBar - 2pcs each
• C3: WoodBar - 1pc
• C6: WoodBar - 3pcs
• C9: WoodBar - 1pc
• D1: WoodBar - 1pc
• E2: Piston Steam - 2pcs

Hardware List (Box 1)

• 1: Screws 1/4" x40mm - 16pcs
• 2: Bolts Ø1/3" x 40 mm - 2pcs
• 3: Canopy head though - 2pcs
• 4: Bolts Ø1/4" x 40 mm - 2pcs
• 5: Bolts Ø1/4" x 60 mm - 4pcs
• 6: Bolts Ø1/4" x 80 mm - 14pcs
• 7: Bolts Ø1/4" x 100 mm - 16pcs
• 8: Allen Key - 2pcs ?️
• 9: Wood dowel Ø8 x 30 mm - 66pcs ?️
• 10: Ø1/4" x 13 mm Horizontal-Hole bolts - 34pcs
• 11: Angle Metal - 18pcs
• 12: Angle Metal - 3pcs
• 13: Ø20 / Ø6 x 2 mm Washer - 2pcs ⚪
• 14: Nut - 4pcs ?
• 15: Bearings - 2pcs ?️
• 16: M8 x 80 mm Plastic anchor - 6pcs ⚓
• 17: Wood Screws M4 x 20mm - 39pcs ?
• 18: Lock - 1set ?
• 19: Wood Screws M4 x 30mm - 55pcs ?
• 20: Wood Screws M4 x15mm - 72pcs ?
• 21: Cam bolt - 30pcs ⚙️
• 22: Cam lock Ø15 x 12 mm - 30pcs ⚙️
• 23: Screws M5 x75mm - 6pcs ?

Assembly Tools Required (Not Included): Screwdriver, Wrench.

Assembly Steps

Step 1

Attach parts A8, A9, A3, A1, A7, A5 using hardware 9 (6pcs) and 7 (8pcs), and 10 (8pcs). The diagram shows the initial frame assembly.

Step 2

Continue assembling the frame by attaching parts A8, A4, A9, A1, A2, A6 using hardware 9 (6pcs) and 7 (8pcs), and 10 (8pcs). This step builds upon the previous frame structure.

Step 3

Assemble the main bed frame structure using parts B1, B2, B3, B4. Secure them with hardware 10 (14pcs), 9 (10pcs), and 6 (14pcs). The diagram shows the base frame taking shape.

Step 4

Attach parts D4 to the frame using hardware 21 (6pcs). This step involves securing long support beams.

Step 5

Assemble a sub-frame or support structure using parts D4, D5, D6, D7. Secure these components with hardware 22 (6pcs) and 9 (12pcs). The diagram shows a section of the bed base being constructed.

Step 6

Attach part 9 (wood dowels) to the main frame using hardware 1 (4pcs) and 9 (10pcs). This step likely prepares for connecting larger panels.

Step 7

Install the metal corner links D8 and D9 using hardware 17 (20pcs). These are crucial for structural integrity and potentially for the bed's mechanism.

Step 8

Attach parts C1 to the frame using hardware 21 (10pcs). This step involves connecting more structural elements.

Step 9

Connect parts C1 and C2 using hardware 22 (1pc) and 9 (2pcs). The diagram shows a mechanism being assembled.

Step 10

Assemble a section of the bed base using parts C2, C3, C4, C5. Secure these with hardware 22 (2pcs) and 9 (4pcs). This step continues building the bed platform.

Step 11

Attach the slats C6 to the bed frame using hardware 1 (6pcs). This forms the main sleeping surface support.

Step 12

Assemble another section of the bed base using parts C5, C4, B9. Secure these with hardware 22 (2pcs) and 9 (4pcs). This step adds more components to the bed platform.

Step 13

Connect parts C5, C1, and E3 using hardware 22 (5pcs) and 9 (10pcs). This step involves attaching more structural and possibly functional components.

Step 14

Attach parts C8 and D1 to the frame using hardware 10 (4pcs), 9 (8pcs), and 5 (4pcs). This step adds further structural support.

Step 15

Install components using hardware 21 (14pcs). The diagram shows screws being inserted into pre-drilled holes.

Step 16

Install components using hardware 22 (14pcs). This step likely involves securing more parts of the bed mechanism or frame.

Step 17

Attach angle metal pieces (11) and secure them with screws (20). Use 18pcs of angle metal and 72pcs of screws (20). This step reinforces the structure.

Step 18

Attach slats D3 to the bed frame using hardware 19 (55pcs). This step completes the bed platform.

Step 19

Install metal corner links E1 using hardware 17 (16pcs). These are likely part of the folding mechanism.

Step 20

Attach the pistons E2 using hardware 15 (2pcs) and 14 (2pcs). These are likely gas springs for smooth operation.

Step 21

Install wheels using hardware 2 (2pcs). The diagram shows wheels being attached to the bed frame for mobility.

Step 22

Secure components using hardware 14 (2pcs). This step involves attaching nuts.

Step 23

Attach parts C7 using hardware 13 (2pcs), 4 (2pcs), and 3 (2pcs). This step appears to be attaching handles or support arms.

Step 24

Install the lock mechanism (18) (1 set). This step secures the bed in its closed position.

Wall Mounting Guide

Warning: Wall fixing screws are not included. Different wall materials require different types of screws/fixings. Ensure you use the correct ones for your walls and seek professional advice if unsure. Failure due to incorrect fixings is the installer's responsibility.

Important: When drilling into walls, always check for hidden wires or pipes.

Types of Walls and Fixings

You can use one of the following types of wall plugs if your walls are made of brick, breezeblock, concrete, stone, or wood:

• 1. General Purpose wall plug: Suitable for light loads. Use specialist fittings for heavy loads or aerated blocks.
• 2. Plasterboard wall plug: For light loads on plasterboard partitions.
• 3. Cavity Fixing wall plug: For use with plasterboard partitions or hollow wooden doors.
• 4. Cavity Fixing - Heavy Duty wall plug: For heavy loads like shelving, wall cabinets, and coat racks.
• 5. Hammer Fixing wall plug: For walls with plasterboard. Fixes to the wall behind the plasterboard.
• 6. Shield Anchor wall plug - Heavy loads: For heavier loads such as TVs, speakers, and satellite dishes.

Care and Maintenance: Periodically check all fittings and wall fixings to ensure they have not come loose and retighten as necessary.

Wall Mounting Options

Option 1: Mounting to a standard wall

Step 1: Determine the position of the bed in the room. The diagram shows the bed in its closed position against a wall, with arrows indicating measurement from side walls.

Step 2: Place the bed back in its position, ensuring it is vertical and horizontal. Arrows indicate sliding the bed into place.

Step 3: Mark the drill holes according to the actual product placement. The diagram shows measurements and dashed lines for hole placement on the wall.

Step 4: Drill the positions marked in Step 3 and secure the plug using hardware 16 (6pcs). The diagram shows drilling into the wall and inserting a wall plug.

Step 5: Raise the bed from its previously fixed position, press it against the wall, and lower it as shown. This step requires 4 people: 2 to hold the cabinet in place and 2 to tilt the bed until accessories are in place. The diagram shows close-ups of mounting brackets being attached to the wall and the bed frame.

Step 6: Attach mounting brackets (12) using screws (23) (3pcs). The diagram shows the bracket being screwed into the wall, with dimensions like 1380mm and 30mm indicated.

Step 7: Secure the bed to the wall using hardware 17 (3pcs). The diagram shows screws being inserted through the mounting brackets into the bed frame.

Option 2: Mounting to a concrete wall

This option is recommended if your house wall is concrete.

Step 1: Determine the position of the bed in the room. The diagram shows the bed in its closed position against a wall, with arrows indicating measurement from side walls.

Step 2: Place the bed back in its position, ensuring it is vertical and horizontal. Arrows indicate sliding the bed into place.

Step 3: Mark the drill holes according to the actual product placement. The diagram shows measurements and dashed lines for hole placement on the wall.

Step 4: Drill the positions marked in Step 3 and secure the plug using hardware 16 (6pcs). The diagram shows drilling into the wall and inserting a wall plug.

Step 5: Raise the bed from its previously fixed position, press it against the wall, and lower it as shown. This step requires 4 people: 2 to hold the cabinet in place and 2 to tilt the bed until accessories are in place. The diagram shows close-ups of mounting brackets being attached to the wall and the bed frame.

Step 6: Attach mounting brackets (12) using screws (23) (3pcs). The diagram shows the bracket being screwed into the wall, with dimensions like 30mm indicated.

Step 7: Secure the bed to the wall using hardware 17 (3pcs). The diagram shows screws being inserted through the mounting brackets into the bed frame.

Final Product Views

The final pages show the bed in its open and closed states, illustrating its functionality.