LG Innotek User Manual
Product Name: Blue Adapter
Model Name: ETGBBTBP01
Secret Level 2
The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or in part without prior written permission of LG Innotek.
Designed: K.H. CHOI | Checked: I.H. PARK | Approved: S.D. CHOI
Date: 2020.12.09
Document No.: [Document Number Not Specified]
Page: 9
Table of Contents
1. Features
ETGBBTBP01 is the Bluetooth Low Energy 4.2 USB Dongle with PCB Printed Antenna. ETGBBTBP01 is based on TI CC2640R2FRHB solution.
- ARM® Cortex®-M3, 32bit, 48MHz clock Speed
- 275KB of Nonvolatile Memory Including 128KB of In-system Programmable Flash
- Up to 28KB of System SRAM, of Which 20KB is Ultra-Low Leakage SRAM
- 8KB of SRAM for Cache or System RAM Use.
- Integrated 2.4GHz Antenna
- Supported data rates 1Mbps, 2Mbps Bluetooth® low energy mode
- Support USB Interface with USB to UART Converter IC
- Size: 70.0 x 21.7 x 10.0 mm³ (USB Dongle)
- Application: Health care and Medical, Connected Appliances
2. Block Diagram
The block diagram illustrates the internal components and connections of the ETGBBTBP01 module. It shows the ANT, BLE4.2 MAC/BB, MCU (Cortex M3), Flash 128KB, SRAM 20KB, PMU, UART, Interface Block, and Clock sources (24MHz and 32.768KHz), all connected to a 3.3V and 5V power supply via an LDO.
3. Absolute Maximum Ratings
| Parameter | Min | Max | Unit |
|---|---|---|---|
| Storage Temperature | -40 | +100 | °C |
| Storage Humidity (@ 40°C) | - | 90 | % |
Caution: The specifications above define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extended periods can adversely affect the long-term reliability of the device.
Other conditions:
- Do not use or store modules in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture.
- Store the modules where the temperature and relative humidity do not exceed 5 to 40°C and 20 to 60%.
- Assemble the modules within 6 months. Check the soldering ability in case of 6 months over.
4. Operating Test Conditions
| Parameter | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Operating Temperature | 5 | - | +50 | °C |
| Operating Humidity (40°C) | - | - | 85 | % |
| Supply Voltage | 4.75 | 5.0 | 5.25 | Vdc |
5. Electrical Characteristics
5-1. RF Characteristics (Conducted Test)
| PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT |
|---|---|---|---|---|---|
| Receiver sensitivity | 1 Mbps Packet length<=37 bytes, BER=0.1% | -93 | - | -80 | dBm |
| 2 Mbps Packet length<=37 bytes, BER=0.1% | -91 | - | -80 | dBm | |
| Maximum received signal strength | Maximum received signal strength at < 0.1% BER | -10 | -2 | - | dBm |
| Maximum output power | Conducted Test | -3.0 | -1.5 | 0 | dBm |
| Modulation Characteristics | 1 Mbps delta F1 average | 225 | - | 275 | kHz |
| ratio(delta F2/delta F1) | 80 | - | - | % | |
| 1 Mbps delta F1 average | 450 | - | 550 | kHz | |
| ratio(delta F2/delta F1) | 80 | - | - | % | |
| Carrier frequency offset and drift | 1 Mbps |f[n]| | - | - | 150 | kHz |
| |f0 - fn| | - | - | 50 | kHz | |
| Carrier frequency offset and drift | 2 Mbps |f[n]| | - | - | 150 | kHz |
| |f0 - fn| | - | - | 50 | kHz |
* Normal Condition : 25°C, VDD=5V.
* RF characteristics is board limit. It can differ according to standards.
6. Pin Description
| Pin No. | Pin Name | I/O | Pin Description |
|---|---|---|---|
| 1 | VDD | I | VDD 5.0V |
| 2 | UART Rx | I | UART Communication signal line |
| 3 | UART Tx | O | UART Communication signal line |
| 4 | GND | - | GND |
The top view shows the components on the PCB, including the antenna, the main chip (CC2640R2FRHB), and the USB connector.
< Bottom View >
The bottom view shows the other side of the PCB and the casing of the USB dongle. It includes regulatory markings such as FCC ID, IC, KC, ANATEL, and CE.
Label Information:
- Model: ETGBBTBP01
- CMIIT ID: XXXXXXXXXX
- IC: 7414C-ETGBBTBP01
- KC: R-C-LGW-ETGBBTBP01
- ANATEL: HHHHH-FF-FFFFF
- FCC ID: YZP-ETGBBTBP01
- Made in Indonesia
- S/N: 00000
7. Outline Drawing
1) Module
The module outline drawing provides detailed dimensions and tolerances for the PCB and its components. Key dimensions include overall length, width, and height, as well as specific measurements for the USB plug, shield can, and cutting areas. Notes specify dimensional tolerances, lot number requirements, and potential changes to the outer appearance.
2) Case
The case outline drawing shows the external dimensions of the USB dongle casing. It includes the overall length, width, and height, with specific details on the shape and features of the casing. Notes detail dimensional tolerances, material, and finish.
3) Gift Box
The gift box outline drawing provides the dimensions and construction details for the product's packaging. It includes measurements for the box itself, internal partitions, and adhesive areas. Notes specify general tolerances, material (IVORY, 300gr), and printing requirements.
FCC/ISED Statement
FCC Part 15.19
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Part 15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Part 15.21
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device must not be co-located or operating in conjunction with any other antenna or transmitter.
RF Exposure
The device has been evaluated to meet general RF Exposure requirement. The device can be used in portable exposure conditions without restriction.
Responsible Party
LG Innotek USA Inc.
Street Address: 2540 N 1st ST STE 400 SAN JOSE, CA 95131-1016
PHONE: +1-408-350-7661 / FAX: +1-408-955-0329
Canada Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
RF Exposure (Canada)
The device has been evaluated to meet general RF Exposure requirement. The device can be used in portable exposure conditions without restriction.
Exposition RF (Canada)
L'appareil a été évalué pour répondre aux exigences générales en matière d'exposition aux RF. L'appareil peut être utilisé dans des conditions d'exposition portatives sans restriction.
