LG Innotek 4PPoE WLAN Bridge Manual

1. Appearance Description for PoE WLAN Bridge

1. Front/Right side Panel

The right side panel features two buttons, while the front panel displays status LEDs. The following figure illustrates these components.

Diagram Description (Fig 1. Front/Right side View): A white PoE WLAN Bridge device is shown. On the front, there are three indicator lights labeled CAMERA, POWER, and WLAN. On the right side, there are two buttons labeled WPS and RESET.

2. Left side/Back/bottom Panel & Label Information

The back panel contains the product label and power plug. The left panel features the wireless antenna, the bottom plug, and one RJ45 port. The label on the bottom displays the MAC address and serial number.

Diagram Description (Fig 2. Back/Left Side View): The device is shown from the back and left. The left side has a wireless antenna. The back shows an AC blade for power and a PoE RJ45 port labeled "PoE RJ45".

Diagram Description (Fig 3. Label Information): A product label is depicted with the following details:

• Brand: LG INNOTEK
• FCC ID: YZP-ETPFFRPP01
• IC ID: 7414C-ETPFFRPP01
• Input: 100-130V~, 1.5A, 60Hz
• Output: DC 52V ===, 870mA
• Model Name: ETPFFRPP01
• SN: 0011425000001
• MAC: 944444000001
• Compliance: RoHS
• Warning: A WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
• Made In Indonesia
• Certifications: TÜV Rheinland, US

2. Installation Guide

1. PoE Connection with AP

You can connect to an Access Point (AP) using a cellular phone.

1. Insert the PoE WLAN Bridge into AC Power. The PoE WLAN Bridge is in AP mode initially.
2. Turn on the WLAN on your cellular phone and search for the AP List.
3. Select the SSID "ADC_Bridge_xxx". The "xxx" represents the final three numbers of the MAC Address (e.g., "e2b" in the example picture). You can check the MAC address on the product label.
4. Open an internet explorer and input any URL address. Accessing any URL will connect you to the PoE WLAN Bridge web page.
5. Please select the language. The PoE WLAN Bridge supports three languages.
6. Please click "Scan for WLAN Networks". If you are using a hidden SSID, input the SSID manually.

Screenshot Descriptions for Steps 1-6:

• Screenshots 1 & 2: Show a mobile phone's Wi-Fi settings screen displaying a list of available Wi-Fi networks, including "ADC_Bridge_e2b" and other networks like "네이버" (Naver) and "유진성형외과" (Yujin Plastic Surgery). The connection status is indicated.
• Screenshot 3: Displays a mobile keyboard interface, typically used for entering text such as an SSID or password.
• Screenshot 4: Shows a web browser displaying a page with a URL (e.g., www.naver.com) and various content, including advertisements and news headlines. This represents the page accessed after connecting to the bridge.
• Screenshot 5: Presents a language selection screen with options for "English", "Spanish", and "Portuguese".
• Screenshot 6: Shows the "WLAN Settings" screen, allowing the user to scan for Wi-Fi networks or input a hidden SSID.

Steps 7-11:

7. You can see the AP List and signal strength (RSSI). Click the AP SSID that you used in your test.
8. Click the connect message.
9. You will see a "Please wait..." message.
10. If you finish the process, your cellular phone will disconnect from the PoE WLAN Bridge.
11. The PoE WLAN Bridge will reboot. After a few seconds, the WLAN LED will turn red. A red WLAN LED indicates that the PoE WLAN Bridge is connecting with the AP. If the WLAN LED is blinking blue, the AP connection is complete.

Screenshot Descriptions for Steps 7-11:

• Screenshot 7: Shows the AP list with signal strength (RSSI) values. The user is prompted to click the connected AP's SSID.
• Screenshot 8: Displays a "Connect" button, likely within the mobile phone's Wi-Fi interface.
• Screenshot 9: Shows a "Please wait..." message on the mobile screen, indicating a process is underway.
• Screenshot 10: Displays a message stating "Cannot display the webpage" with suggestions to check signal strength, try again later, or verify the web address. This might occur after the bridge has established its own connection or during a transition.
• Screenshot 11: Shows the PoE WLAN Bridge device again, with the WLAN LED highlighted, indicating its status.

2. PoE Connection with Power Device(Camera)

1. After AP connection, you can connect the PoE WLAN Bridge and the Power Device (Camera) using an Ethernet Cable.
2. Make sure that your camera is connected to the WLAN Bridge CAMERA port with an Ethernet cable (wired).

Diagram Description: The PoE WLAN Bridge is shown connected via a "LAN Cable (CAMERA)" to a surveillance camera. The cable is plugged into the port labeled "CAMERA" on the bridge.

FCC/ISED Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. This device must not transmit simultaneously with any other antenna or transmitter.

RF Exposure Information (French): L'antenne (ou les antennes) doit être installée de façon à maintenir à tout instant une distance minimum de au moins 20 cm entre la source de radiation (l'antenne) et toute personne physique.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

• (1) this device may not cause interference, and
• (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Canadian Compliance (French): Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

Responsible Party: LG Innotek USA Inc.

Street Address: 2540 N 1st ST STE 400 SAN JOSE, CA 95131-1016

PHONE: +1-408-350-7661 / FAX: +1-408-955-0329