Anslut Floor Fan

OPERATING INSTRUCTIONS

Important! Read the user instructions carefully before use. Save them for future reference.

(Translation of the original instructions)

BRUKSANVISNING (NO)

Viktig! Les bruksanvisningen nøye før bruk. Ta vare på den for fremtidig bruk.

(Oversettelse av original bruksanvisning)

BRUKSANVISNING (SE)

Viktigt! Läs bruksanvisningen före användning. Spara den för framtida bruk.

(Original bruksanvisning)

INSTRUKCJA OBSŁUGI (PL)

Ważne! Przed użyciem uważnie przeczytaj instrukcję obsługi! Zachowaj ją na przyszłość.

(Tłumaczenie oryginalnej instrukcji)

Care for the environment!

Must not be discarded with household waste! This product contains electrical or electronic components that should be recycled. Leave the product for recycling at the designated station e.g. the local authority's recycling station.

Jula reserves the right to make changes. In the event of problems, please contact our customer service.

www.jula.com

Assembly

FIG. 1 shows the components of the fan:

• 1. Motor
• 2. Lock knob
• 3. Pillar
• 4. Foot
• 5. Angled screw
• 6. Plastic nut
• 7. Fan hub casing
• 8. Rear grille
• 9. Fan blade
• 10. Front grille

FITTING THE FOOT

Fit the bottom end of the pillar in the foot and screw in place with the angled screw. (FIG. 2)

FITTING THE PILLAR

1. Pull out the telescopic top part of the pillar to the required height and lock by tightening the height adjusting ring.

2. Fit the motor housing and lock in the required position with the lock knob. (FIG. 3)

FITTING THE FAN BLADE AND GRILLE

1. Align the holes on the back of the grille with the pins on the motor housing.

2. Screw on the plastic nut clockwise and tighten to fasten the back grille.

3. Push the fan blade on the motor axle and then turn the fan by hand to check that it rotates freely.

4. Screw on the fan hub casing anticlockwise and tighten. Now fit the front grille. (FIG. 4)

FITTING THE FRONT GRILLE

1. Align the clips on the front grille on the top masks on the back grille from above. The correct alignment is shown in the figures, seen from the front from the back of the product. (FIG. 5, FIG. 6)

2. Press the grille halves together with both hands until they lock in place.

HOW TO USE ADJUSTMENTS

FIG. 7

Oscillation

Connect the oscillation function by pressing the knob (1) on the top of the motor housing. Disconnect the oscillation function by pulling out the knob.

Adjusting the angle

To angle the motor housing (2), and therefore the air flow up or down, carefully press the guard grille up or down.

Height adjustment

To raise or lower the motor housing, release the height adjusting ring (3), pull out or push together the telescopic pillar to the required height and lock by tightening the height adjusting ring.

CONTROL PANEL

FIG. 8

• 1. Indicator of natural ventilation
• 2. Indicator night mode
• 3. Indicator of fan speed
• 4. Indicator of timing
• 5. Timer setting
• 6. Run mode setting
• 7. Speed setting
• 8. Power switch

Timer setting

Press the time setting button repeatedly or hold in to stepwise increase the set run time. If for example you want 7 hours of run time, press the button repeatedly until the status lights for 1, 2 and 4 hours go on at the same time. The set run time is then 1 + 2 + 4 = 7 hours. The time status lights go on and off so that the remaining run time is shown in steps of 1 hour. Press the time setting button to run the fan continuously. In continuous run mode all the status lights are off. The timer can also be set from the remote control.

Run mode setting

Press the run mode button M (mode) repeatedly or hold in to step through the run modes normal, natural and night mode. The status lights show the set run mode. The run mode can also be set from the remote control.

Speed setting

Select natural ventilation by pressing the run mode button and then pressing the speed button repeatedly to select the 3 different speeds. The speed can also be set from the remote control.

Power switch

Press the power switch to start and switch off the product. The fan starts working at low speed. Press once again to switch off. The fan can also be started and switched off with the remote control.

USING THE REMOTE CONTROL

Point the remote control at the fan and press the required button. The remote control has a range of 5 metres within an angle of 30 degrees to the left and right of the receiver.

MAINTENANCE

REPLACING THE BATTERY

1. Open the battery compartment by pressing the lid and pulling it out. (FIG. 9)

2. Insert the batteries with the correct polarity in accordance with the markings inside the battery compartment.

3. Replace the cover. (FIG. 10)

CLEANING

NOTE: Pull out the plug from the power point before installation and/or cleaning.

• The fan should be cleaned once a month.
• Clean the fan with a soft cloth moistened with a mild detergent. Make sure that no water or other liquid gets into the fan.

NOTE: Do not use petrol, solvents or detergents that can damage the plastic parts.

TECHNICAL DATA

Service value standard: IEC 60879:1986 (corr. 1992)

Contact details: www.jula.com