Eureka Forbes Aquaguard Select Water Filtration Systems

Environmental Responsibility and Self-Cleaning Technology

? Environment Protection: Eureka Forbes is committed to environmental protection. We urge customers to recycle packaging materials or take them to a recycling facility. Your product is designed for longevity, but when upgrading or replacing, please dispose of it responsibly at an e-waste disposal center. Eureka Forbes can guide you on this process, helping to make the world a cleaner place.

⚙️ Self-clean: To maintain optimal efficacy, water treatment plants require periodic cleaning. Aquaguard Select water treatment systems feature an automatic back-flushing arrangement that cleans the unit automatically, allowing you more time for other activities.

Pre-Installation Checklist

1. Choose an easily accessible location for servicing, away from direct sunlight and rain. The site should minimize potential damage from leaks.
2. Ensure a stable power supply with 100-240V/50-60Hz output.
3. A drain facility must be available for the automatic backflush process.
4. Verify that all items, including accessories and media, are present before installation.
5. Installation must be performed exclusively by a Eureka Forbes representative or authorized agent.

Installation Procedure

1. Position the FRP vessel in a safe, spacious location suitable for servicing.
2. Attach the bottom strainer to the UPVC pipe using glue.
3. Insert the pipe with the bottom strainer into the FRP vessel. Trim excess pipe so its height, plus the bottom strainer, matches the vessel's top height when placed inside. Refer to Figure 1 for guidance.
4. Fill the vessel with media according to the "Order of media filling" table.
5. Fit the top strainer onto the multiport valve.
6. Attach the 2.5-inch O-ring.
7. Connect the multiport valve, with the top strainer attached, onto the UPVC pipe.
8. Gently press the multiport valve down and tighten it. ⚠️ DO NOT OVERTIGHTEN.
9. Install the Flow Sensor into the multiport valve's outlet using the 1-inch Male-Male adaptor and O-rings at both ends.
10. Connect the multiport valve cable to the flow sensor.
11. Connect the pipelines as illustrated in Figure 2.
12. If multiple filter systems are connected in series, link the interconnect cable between the multiport valves.
13. A company representative or authorized agent must program the multiport valve.
14. Run water through the system and check for any leaks.
15. Do not connect the output line until the flushing process is complete.
16. Flush the filter system until the output water runs clear.
17. Connect the output line to the storage tank.

Diagrams and Media Filling

Figure 1 - Cross Section

This diagram illustrates the internal components of a typical Aquaguard Select filter vessel. It shows the arrangement of a riser pipe, base O-ring, resin tank, top strainer, and the multiport valve, indicating how they fit together within the vessel.

Figure 2 - Pipe Layout

This diagram depicts the external plumbing connections for the water filtration system. It shows the placement of valves (Valve A, Valve B, Valve C), an optional pressure gauge, and how these components are interconnected in the overall pipe layout.

Order of Media Filling

Aquaguard Select Sediment Filter

The Aquaguard Select Sediment Filter protects your family from suspended particles that may be present in tap water. Impurities can enter water lines due to reasons such as unclean overhead tanks, sumps, or pipeline leakages. This filter effectively removes sediments, which often harbor other impurities like metals and microorganisms, ensuring cleaner water for the user.

Technical Specifications

Aquaguard Select Activated Carbon Filter

Unclean overhead tanks and sumps can promote microorganism growth, leading to foul-smelling water. The Aquaguard Select Activated Carbon filter uses NSF-certified carbon granules to treat water, removing unpleasant odors, organic chemicals, and chlorine byproducts. Its self-cleaning system regularly flushes out contaminants, maintaining peak performance.

Technical Specifications

Aquaguard Select Iron Remover

The Aquaguard Select Iron Remover utilizes imported iron-adsorbing media to treat water with excessive iron content. High iron levels can cause itchy skin, clogged pores, rough hair, hair loss, and stains on bathrooms and taps. This system features a self-cleaning mechanism that regularly flushes out contaminants to ensure continuous effective operation.

Technical Specifications

Terms and Conditions

The goods are warranted against defects arising from faulty designs, workmanship, and materials for 12 months from the date of installation or 15 months from the date of sale, whichever is earlier, subject to the following conditions:

1. Customers must promptly notify the company in writing of any defects and provide adequate opportunity for inspection, testing, and remedy. The goods may need to be deposited with the company's office/service center along with the original invoice.
2. The inspection and test report from the company's office/service center will be final and binding for determining defects, repairs, or alterations.
3. The company or its authorized agent may retain any defective part replaced under warranty.
4. Notwithstanding anything to the contrary, the company's liability under this warranty is limited to the first sale of the goods to the customer and does not extend to secondary sales.
5. Liability is limited to defects occurring under normal operation, proper use, and prescribed maintenance. The warranty excludes defects due to negligence, abuse, misuse, faulty care, unauthorized repairs, or use with incorrect electrical supply or disturbances.
6. Warranty is valid only if the goods are installed by the company or its authorized agency at the specified location.
7. Consumable media like sand or activated carbon, subject to normal wear and tear, are not covered by this warranty.
8. The customer waives claims against the company, its employees, and agents for death, injury, or property damage resulting from equipment failure, accident, fire, or improper use, or causes beyond the company's control.
9. The company's liability shall not exceed the price paid by the customer for the goods as stated in the invoice.

General Definitions

1. "The Goods": Refers to the products described in the order form.
2. "The Customer": Refers to the original purchaser of the goods from the company.
3. "The Company": Refers to Eureka Forbes Ltd.
4. "General terms and conditions": Refers to the terms agreed upon and printed on the order form.
5. "Invoice": Refers to the invoice issued by the company detailing the goods, purchase price, and customer information.
6. "User manual": Refers to the instructions for installation, use, and maintenance provided by the company.

Post-Warranty Services

Customers may opt for a yearly service contract at prevailing company rates and terms. Alternatively, equipment can be serviced on an actual basis by contacting the company's service center, where the customer pays for labor and necessary spares at current rates. Such services are available in towns/places where Eureka Forbes has service centers.

If component replacement or repair is necessary during servicing, the customer will be charged according to the company's prevailing price list.

Eureka Forbes Ltd. reserves the right to offer annual maintenance contracts and ensure spare parts availability for up to 5 years from the invoice date.

Annual Maintenance Contract (AMC)

Purchasing a Comprehensive AMC provides protection against expensive repairs throughout the machine's working life. Comprehensive AMCs cover spare parts and periodic/complaint calls. However, consumables/media are chargeable extra at prevailing rates. For absolute peace of mind, consider a Comprehensive AMC. Call 1860 266 1177 for details.