GL-iNet Mudi Portable 4G LTE Router

Let's Get Started

Welcome to your new Mudi Portable 4G LTE Router. This guide will help you set it up quickly.

Setting Up Your Mudi Router

Step 1: Insert Cards & Power On

Before powering on, insert your MicroSD card (optional) and Nano SIM card (optional) into the designated slots. Note: Hot-plugging for MicroSD and Nano SIM cards is not supported.

To turn on the router, press and hold the power button for more than 3 seconds. Upon powering up, your Mudi router will broadcast two Wi-Fi signals: 2.4G and 5G, both using the same SSID: GL-E750-xxx.

Step 2: Connect via Wi-Fi

On your device (laptop, smartphone, tablet), search for the Wi-Fi network named GL-E750-xxx. Connect to this network. The default Wi-Fi password is printed on the bottom label of your router.

Step 3: Connect via LAN (Optional)

Alternatively, you can connect your computer directly to the router using an Ethernet cable. Plug one end of the cable into the LAN port of the USB-C port replicator and the other end into your computer.

Step 4: Set Up Router

Open a web browser on a connected device and navigate to http://192.168.8.1. This will take you to the router's setup page where you can choose your preferred language and configure settings.

Support and Warranty Information

Router Components

The Mudi router features the following ports and buttons:

• USB-C port replicator: For power and data connectivity.
• Power port: Connect the power adapter here.
• Ethernet port (LAN): For wired network connections.
• USB2.0 port: For connecting USB devices.
• Mode switch: To change operating modes.
• Power button: To turn the router on/off.
• 0.96-inch OLED display: Shows status information.
• MicroSD card slot: For optional MicroSD card storage.
• Nano SIM card slot: For optional Nano SIM card connectivity.
• Reset button: Used for network repair or factory reset.

Repair / Reset

If you encounter issues accessing the setup page or connecting to the router, you can use the reset button with a pin:

• Press and hold the reset button for 3 seconds, then release to repair your network connection.
• Press and hold the reset button for 10 seconds, then release to reset the router to its factory default settings. All user data will be erased.

Technical Support

For detailed and updated instructions, please visit the official GL-iNet documentation website:

https://docs.gl-inet.com/en/3/

For further assistance, you can reach out through the following channels:

• Email: support@gl-inet.com
• Facebook: facebook.com/gl.inet.wifi/
• Forum: forum.gl-inet.com
• You can also seek help from communities like OpenWrt or LEDE.

Warranty Information

GL Technologies provides a one-year limited warranty for routers and a three-month limited warranty for accessories. Additional warranty periods may apply based on local laws.

It is highly recommended to use the included 5V/2A power adapter. The warranty will be voided if damage occurs due to failure to follow instructions, modification of internal components (PCBA, case), use of third-party firmware, or improper use (e.g., incorrect voltage, extreme temperatures, water damage, dropping).

Please note that images in documentation are for reference only. GL Technologies reserves the right to modify materials without prior notice.

Compliance Information

FCC ID: 2AFIW-E750V2C4 | 2AFIW-E750V2C6

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If interference occurs, users are encouraged to try measures such as reorienting the antenna, increasing separation between equipment and receiver, or consulting a dealer or technician.

Specific Absorption Rate (SAR) Information: This Portable 4G LTE Router meets government requirements for radio wave exposure. The guidelines are based on standards developed by independent scientific organizations. The FCC SAR limit for the USA is 1.6 W/kg averaged over one gram of tissue. This device was tested for typical body-worn operations with the back of the device kept 0mm from the body. To maintain compliance, use accessories that maintain this 0mm separation distance and do not contain metallic components.

EU Declaration of Conformity: GL TECHNOLOGIES (HONG KONG) LIMITED declares that this radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: https://www.gl-inet.com/products/certificate.

Functions within the 5150-5350 MHz band for Wireless Access Systems are restricted to indoor use only within all European Union countries.

Operating Frequencies: 2412MHz~2472MHz; 2422MHz~2462MHz; 5150MHz~5250 MHz; 5725MHz~5850MHz.

RF Exposure: The highest measured 10g (simultaneous transmission) Body SAR value is 1.612W/Kg.

Contact Information

Hong Kong Office

GL Technologies (Hong Kong) Limited
Unit 601, Building 5W, Hong Kong Science Park,
Shatin, N.T., Hong Kong

Shenzhen Office

Shenzhen Guanglianzhitong Tech Co., Ltd.
Room 305-306, Skyworth Digital Building, Shiyan Street,
Baoan District, Shenzhen, China, 518000
(+86-0755-86606126)