AMP Lighting Installation & Maintenance Guide

Important Safety Instructions: Read Before Installation

This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty.

These instructions do not intend to cover all variations in installation, operation, maintenance or mounting situations.

1. Make sure that the power is turned OFF before installing or servicing this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
6. The main low voltage cable is intended for shallow burial - less than 6 inches (152 mm).

Important Safety Instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS

Lighted lamp is HOT!

WARNING - TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.

1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
6. Do not operate the luminaire fitting with a missing or damage shield.

SAVE THESE INSTRUCTIONS

Product Dimensions

15W Floodlight

Diagram Description: A diagram showing the dimensions of the 15W floodlight. Key dimensions include 3 inches, 8 inches, 9 inches, 8.25 inches, R0.25 inches, 7.25 inches, and 00.75 inches.

30 Floodlight

Diagram Description: A diagram showing the dimensions of the 30 floodlight. Key dimensions include 5 inches, 6.75 inches, 5.75 inches, 10 inches, 11.25 inches, R0.25 inches, 9.25 inches, and 00.75 inches.

Package Contents

• A. (1) Fixture Body
• B. IR Remote

Installation

1. Marking for Expansion Bolt Anchors

Mark two points on the mounting surface using the holes on the yoke mount as a guide. These marks will be used for the expansion bolt anchors (not included).

Diagram Description: Shows a fixture body, yoke mount, mounting surface, and a hole, indicating where to mark for expansion bolt anchors.

2. Install Expansion Bolt Anchors

Drill the proper holes using the marks on the mounting surface for the expansion bolt anchors. Insert the expansion bolt anchors into the drilled holes. Tighten the hex nuts on the expansion bolt anchors until they are fastened to the surface.

Diagram Description: Illustrates expansion bolt anchors, a mounting surface, and a mark, showing the process of installing expansion bolt anchors.

3. Install Fixture Body

Remove the hex nuts and washers from the expansion bolts. Attach the yoke mount with fixture body to the bolts and secure with the previously removed washers and hex nuts. Tighten until snug.

Diagram Description: Depicts a fixture body, hex nut, washer, yoke mount, bolt, and mounting surface, demonstrating how to attach the fixture body.

4. Wire Connection

Strip both leads from the fixture pigtail. Using two wire connectors (sold separately), connect the leads from the fixture bodies to the main supply cable leads.

Diagram Description: Shows supply cables from fixture body, a pigtail, wire connectors, and a main supply cable, illustrating the wire connection process.

5. Adjust Fixture Body

Using the wrench, loosen the screws on the side of the fixture to adjust the fixture to your desired orientation. Always tighten the screws after any adjustments.

Diagram Description: Illustrates a fixture body, wrench, and screw, showing how to adjust the fixture body orientation.

Stake Mount

1. Install Stake

Determine the desired location for mounting the stake. Hammer the stake into the ground until the flange of the stake is flush to grade. To avoid damage to the stake, place a board on top of the stake while hammering.

Note: If the ground is hard and the stake is difficult to install, make a crosscut in the ground using a flat shovel.

Diagram Description: Shows a board, stake, ground, and soil, illustrating the process of installing a stake into the ground.

2. Install Fixture to Stake

Attach the coupler onto the stake. Place the yoke mount with the fixture body onto the coupler and secure with the hex nut. Hand tighten until snug.

Diagram Description: Depicts a fixture, hex nut, coupler, yoke mount, ground, stake, and soil, showing how to attach the fixture to the stake.

3. Install Fixture to Stake (Wiring)

Strip both leads from the fixture pigtail. Using two wire connectors (sold separately), connect the leads from the fixture bodies to the main supply cable leads.

Diagram Description: Shows supply cables from fixture body, a pigtail, wire connectors, and a main supply cable, illustrating the wire connection process for stake mounting.

4. Adjust Fixture Body

Using the wrench, loosen the screws on the side of the fixture to adjust the fixture to your desired orientation. Always tighten the screws after any adjustments.

Diagram Description: Illustrates a fixture body, wrench, and screw, showing how to adjust the fixture body orientation when mounted on a stake.

IR Remote

1. Remove Plastic Film

Remove the plastic film from the IR remote before use.

Diagram Description: Shows the IR remote with a backing, a plastic film, and an arrow indicating removal. Also shows a battery and battery bracket with instructions to push and release.

2. IR Remote Functions

NOTE: When using the remote, make sure it is pointed at the sensor in the faceplate so it operates properly.

Diagram Description: A diagram of the IR remote with numbered buttons and their corresponding functions:

• 1. On/Off
• 2. Brightness Control
• 3. 16 color selections
• 4. Flash
• 5. Strobe
• 6. Fade
• 7. Smooth

4. Flash Modes

• Mode 1: Repeats Red, Green, Blue + color cycle for 1 second duration of each of the seven colors within this mode.
• Mode 2: Hit flash a second time and this mode slowly blends the same seven colors from mode one, mixing them together.

5. Strobe Modes

• Mode 1: Pick any color on the remote, then press strobe and that color will strobe every second alternating between on and off.
• Mode 2: Hit strobe a second time and this mode will strobe a blended white color at the same speed as before.

6. Fade Modes

• Mode 1: Pick any color on the remote, then press fade and that color will slowly fade in and out every second.
• Mode 2: Hit fade a second time and it will fade a blended white color in and out at the same speed as before.

7. Smooth Modes

• Mode 1: Repeats a flash cycle of Red, Green, and Blue only.
• Mode 2: Hit smooth a second time and this mode slowly blends Red, Green, and Blue only; in and out of each other at the same speed.

Battery Replacement

1. Replace Battery

Push the side of the battery bracket and carefully remove it from the IR remote. Replace the battery and then insert the battery bracket back into the IR remote.

Replacement Battery Style: CR2025 Button Battery

Diagram Description: Shows the IR remote backing, a battery, and a battery bracket with arrows indicating removal and insertion, and a CR2025 battery label.