AMP G2 EcoPro Low Voltage Landscape Lighting

Product Overview

This guide provides detailed instructions for the installation and maintenance of the AMP G2 EcoPro Low Voltage Landscape Lighting system. The luminaire is designed for outdoor use and requires a compatible low voltage power supply.

Product Illustrations

The luminaire is shown in three views: a side view detailing the adjustable knuckle and stake attachment, a front view of the housing and lens, and a base view showing the connection point for the stake.

Important Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS: READ BEFORE INSTALLATION

This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage, and void the warranty. These instructions do not cover all variations in installation, operation, maintenance, or mounting situations.

1. Ensure power is turned OFF before installing or servicing the luminaire.
2. WARNING: Risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pools, spas, or fountains.
3. This luminaire is intended for use only with a power supply (transformer) rated a maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors suitable for outdoor use.
5. Position the low voltage wire and wire connector within 6 inches (15.2 cm) from a building structure, luminaire, or fitting.
6. The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm).

IMPORTANT SAFETY INSTRUCTIONS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS: LIGHTED LAMP IS HOT!

WARNING: To reduce the risk of FIRE OR INJURY TO PERSONS:

1. Turn off/unplug and allow to cool before replacing the lamp.
2. Lamps get HOT quickly! Contact only the switch/plug when turning on.
3. Do not touch the hot lens, guard, or enclosure.
4. Keep the lamp away from materials that may burn.
5. Do not touch the lamp at any time. Use a soft cloth. Oil from skin may damage the lamp.
6. Do not operate the luminaire fitting with a missing or damaged shield.

SAVE THESE INSTRUCTIONS

Package Contents

A. (1) Fixture Body

B. Mounting Accessory

Product Dimensions

The luminaire has the following approximate dimensions:

• Height: 4.5 inches
• Width: 2 inches
• Lens Housing Diameter: 2.27 inches
• Stake Connection Height: 1 inch

Installation Steps

Step 1: Remove Glare Guard

Loosen the set screw and remove the glare guard from the fixture body.

Diagram Description: An illustration shows the glare guard being detached from the fixture body. Labels indicate "Glare Guard", "Fixture Body", and "Set Screw".

Step 2: Install MR16 Lamp

Insert the MR16 lamp with the correct wattage and type marked on the fixture label.

CAUTION: Do not exceed the maximum wattage marked on the luminaire label.

Diagram Description: An illustration shows the luminaire's socket and an MR16 lamp being inserted into it.

Step 3: Install Glare Guard

Install the glare guard back onto the fixture body and secure it with the previously loosened set screw. Hand-tighten until snug.

Diagram Description: An illustration shows the glare guard being reattached to the fixture body and secured with the set screw.

Step 4: Install Stake

Determine the desired location for mounting the fixture. Hammer the stake into the ground until the flange of the stake is flush to the grade. To avoid damage to the stake, place a board on top of the stake while hammering.

Diagram Description: An illustration shows a stake being driven into the ground. A board is placed on top of the stake to protect it during hammering. Labels: "Board", "Stake", "Ground".

NOTE: If the ground is hard and the stake is difficult to install, make a crosscut in the ground using a flat shovel.

Step 5: Install Fixture Body to Stake

Clear away an area in the ground at the wireway slot on top of the stake. Lay the luminaire pigtail into the wireway slot and screw the fixture body onto the stake. Tighten the lock ring against the stake and hand-tighten until snug.

Diagram Description: An illustration shows the luminaire's pigtail wire being routed through a wireway slot on the stake, and the fixture body being screwed onto the stake and secured by a lock ring. Labels: "Wireway Slot", "Pigtail", "Fixture Body", "Lock Ring", "Stake".

Step 5: Wire Connection

Strip both leads from the luminaire pigtail. Using two UL listed wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.

Diagram Description: An illustration shows the pigtail wires from the luminaire being connected to the main supply cable using wire connectors. Labels: "Pigtail", "Wire Connectors", "Main Supply Cable".

Step 6: Adjust Luminaire Directions

Loosen the knuckle screw at the joint. Rotate the luminaire to your desired direction. Tighten the knuckle screw once your desired direction is achieved.

Diagram Description: An illustration shows the luminaire's adjustable knuckle with a thumb screw, allowing the luminaire to be rotated to the desired direction. Labels: "Thumb Screw", "Luminaire".