AMP® Mini PinnaclePro Black Path & Area Light

IMPORTANT SAFETY INSTRUCTIONS: READ BEFORE INSTALLATION

This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage, and void the warranty.

These instructions do not cover all variations in installation, operation, maintenance, or mounting situations.

• Ensure power is OFF before installing or servicing.
• WARNING: Risk of electrical shock. Install luminaires 10 feet (3.05 M) or more from pools, spas, or fountains.
• Use only with a power supply (transformer) rated a maximum of 300 watts (25 AMPS) at 15 volts.
• Wiring connections must be made with wire connectors suitable for outdoor use.
• Position the low voltage wire and wire connector within 6 inches (15.2 cm) of a building structure, luminaire, or fitting.
• The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm).
• For additional lengths of low voltage cable, contact www.amplighting.com or call 1-813-978-3900.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS: LIGHTED LAMP IS HOT!

WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:

• Turn off/unplug and allow to cool before replacing the lamp.
• Lamps get HOT quickly! Handle only by the switch/plug when turning on.
• Do not touch the hot lens, guard, or enclosure.
• Keep the lamp away from materials that may burn.
• Do not touch the lamp at any time. Use a soft cloth. Oil from skin may damage the lamp.
• Do not operate the luminaire fitting with a missing or damaged shield.

SAVE THESE INSTRUCTIONS

PACKAGE CONTENTS

• A. (1) Stem
• B. (1) Fixture Body
• C. (1) Stake
• A. (1) MR11 Bulb

PRODUCT DIMENSIONS

The fixture has a total height of 26.2 inches. The head of the fixture extends 7.5 inches horizontally. The dimensions of the light-emitting part of the fixture are approximately 4.5 inches in height, 3.2 inches in width, and 2.7 inches in depth.

INSTALLATION STEPS

1. REMOVE LENS AND GLARE GUARD
   Loosen the set screw and remove the glare guard from the lens. Remove the lens from the fixture body.
2. INSTALL BULB
   Insert the MR11 bulb with the correct wattage and type marked on the fixture label. CAUTION: Do not exceed the maximum wattage marked on the luminaire label. NOTE: DO NOT touch the bulb with bare hands. Use a soft cloth to handle the bulb.
3. INSTALL LENS AND GLARE GUARD
   Place the shield over the bulb and thread it onto the fixture. Attach the glare guard back onto the shield and secure it with the set screw.
4. INSTALL STAKE
   Determine the desired location for mounting the fixture. Hammer the stake into the ground until the flange of the stake is flush with the grade. To avoid damage to the stake, place a board on top of the stake while hammering. NOTE: If the ground is hard and the stake is difficult to install, make a crosscut in the ground using a flat shovel.
5. INSTALL FIXTURE
   Clear away an area in the ground at the wireway slot on top of the stake. Lay the luminaire pigtail into the wireway slot and attach the fixture onto the stake.
6. WIRE CONNECTION
   Strip both leads from the luminaire pigtail. Using two wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.
7. ADJUST ANGLE OF FIXTURE
   Using an Allen Wrench, loosen the adjustment screws and modify the fixture body to the desired angle. Then tighten the adjustment screws.

INSTALL/REPLACE LAMP

Remove the glare guard and the lens to expose the MR11 lamp. Replace it with the correct wattage and type marked on the fixture label. Then, reinstall the lens and the glare guard.

IMPORTANT: The MR11 lamp must be protected from moisture and dust at all times. Always reinstall the lens and the glare guard when removed.