MyBat Pro Serene

WELCOME

Thank you for using the MyBat Pro Serene True Wireless Earbuds. Using the purest wireless sound, you can enjoy a high-definition audio experience that is clear, natural, and unrivaled.

Please read this user manual carefully and keep it for future reference.

PACKAGE INCLUDES

The package contains:

• True Wireless Earbuds x 1 pair
• Charging Case x 1
• USB-C Cable x 1
• Ear Caps (The M earcap is installed on the earphones)
• User Manual x 1

[Diagram: Illustration showing the contents of the package: earbuds, charging case, USB-C cable, and ear caps in various sizes.]

PRODUCT OVERVIEW

Earbuds

• [Part 1]: LED Indicator
• [Part 2]: Touch Button
• [Part 3]: Microphone
• [Part 4]: Charging Contacts

[Diagram: Illustration of the earbuds with numbered callouts pointing to the LED Indicator, Touch Button, Microphone, and Charging Contacts.]

Charging Case

• [Part 1]: Charging Pins
• [Part 2]: Charging Case Indicator
• [Part 3]: USB-C Charging Port

[Diagram: Illustration of the charging case highlighting the Charging Pins, Charging Case Indicator light, and USB-C Charging Port.]

HOW TO CHARGE

Fully charge your earbuds and case before first use. A full charge of the earbuds takes approximately 1 hour, while a full charge of the charging case takes approximately 2 hours.

Charging the Case

Connect the included USB-C charging cable to a power supply and plug it into the case to charge.

[Diagram: Charging case connected via USB-C cable to a power source.]

Charging the Earbuds

The earbuds will charge when placed inside the case.

[Diagram: Earbuds placed inside the charging case for charging.]

CHARGING CASE INDICATOR STATUS

• Charging: White light flashing
• Fully Charged: White light always on

POWER ON/OFF

Power On:

Open the charging case and remove the earbuds.

Power Off:

Place the earbuds back into the charging case and close the case. The earbuds will automatically power off.

NOTE: The earbuds will automatically shut down after no connection within 3 minutes.

[Diagram: Visual representation of earbuds being removed from the charging case (Power On) and placed back into the case (Power Off).]

HOW TO PAIR

True Wireless Stereo Connection

Open the charging case and remove the earbuds. The earbuds will automatically power on. The right earbud will automatically connect with the left earbud.

Pairing To Your Devices

1. Open the charging case and remove the earbuds. The earbuds will automatically power on and enter pairing mode.
2. Turn on the Bluetooth of your phone.
3. Select "MyBat Pro Serene" from the list of found Bluetooth devices and pair.

[Diagram: Smartphone screen displaying Bluetooth settings with "MyBat Pro Serene" selected for pairing.]

AUDIO CONTROLS

CALL CONTROLS

VOICE CONTROLS

SPECIFICATIONS

Model:

MyBat Pro Serene

Input:

DC 5V/500mA

Rated Output Power:

5mW

Battery Capacity:

30mAh x 2 (Earbuds), 300mAh (Charging Case)

Charging Time:

1 Hour (Earbuds), 2 Hours (Charging Case Via USB)

Playtime:

4 Hours (Varies by volume level and content)

Driver size:

13mm diamond coated driver x 2

Bluetooth Version:

V5.3

Bluetooth Range:

10m/33ft

Frequency Response:

20Hz ~ 20kHz

Impedance:

32Ω

Bluetooth Frequency:

2402mHZ - 2480MHz

Bluetooth Profile:

AVRCP, A2DP, HFP, HSP

Audio Codec Format:

SBC, AAC, aptX

IMPORTANT SAFETY INSTRUCTIONS

To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.

Be sure to observe the following guidelines when using your earpieces:

• Listen at reasonable volumes for reasonable periods of time.
• Be careful not to adjust the volume continuously upwards as your hearing adapts.
• Do not turn up the volume so high that you can't hear what's around you.
• You should use caution or temporarily discontinue use in potentially hazardous situations.
• Excessive sound pressure from earphones and headphones can cause hearing loss.
• Using headphones with both ears covered while driving is not recommended and may be illegal in some areas while driving.
• For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must not accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov