Beldray 1200 W Halogen Heater

Introduction

This document provides instructions for the Beldray 1200 W Halogen Heater, a portable, practical, and convenient heating solution.

Safety Instructions

General Safety Precautions

• This is not a toy; children should be supervised to ensure they do not play with the product.
• Always unplug the product and allow it to cool fully after use and before any cleaning or maintenance.
• Normal voltage is still present in this product as long as it is connected to the electrical source.
• If the power supply cord, plug, or any part of the appliance is malfunctioning or has been dropped or damaged, cease using the product immediately to avoid potential injury.
• This appliance contains no user-serviceable parts; only a qualified electrician should carry out repairs. Improper repairs may place the user at risk of harm.
• Keep the product and its power supply cord out of the reach of children and away from heat or sharp edges that could cause damage. This includes parts that may become hot during use.
• Keep furniture, curtains, and other flammable material at least 1 metre away from the product.
• Do not run the supply cord under carpets, rugs, etc., or anywhere it may present a trip hazard.
• Do not immerse the product or plug in water or any other liquid.
• Do not operate the product with wet hands.
• Do not use this product in the immediate surroundings of a bath, a shower, or swimming pool.
• Do not leave the product unattended whilst connected to the mains power supply or when in use.
• Do not remove from the mains power supply by pulling the cord; switch off and remove the plug by hand.
• Do not use this product for extended periods of time.
• Do not leave the product plugged in or operating overnight.
• Do not use the product for anything other than its intended use.
• Do not block the air intake of the product; place in an open, well-ventilated space.
• Do not use this product outdoors.
• Do not attempt to move the product whilst it is in use.
• Do not put objects into any of the openings.
• Do not use the product with a programmer, timer, separate remote-control system, or any other device that will switch the product on automatically, as there is a risk of fire if the heater is covered or positioned incorrectly.
• Do not clean the product with abrasive chemicals or materials such as scourers, as they may damage the product and impair future function. This includes insecticide and chemical solvents.
• Only lift the product with the carry handles provided.
• The product should be used on a stable, heat-resistant surface.
• The product must not be located immediately below or next to a mains power supply.
• Never use accessories that are not recommended or supplied by the manufacturer, as it could cause danger to the user and damage to the product.
• Use of an extension cord with the product is not recommended.
• This product is intended for domestic use only and should not be used for commercial purposes.
• [Caution]: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
• [Warning]: Hot surface - do not touch the hot section or heating components of the product.
• [Warning]: In order to avoid overheating, do not cover the product.
• This product is not equipped with a device to control the room's temperature.
• Do not use this product in small rooms whilst occupied by persons incapable of leaving the room on their own, unless constant supervision is provided.

Specific Safety Features

Stability Safety Cut-out

This halogen heater is fitted with a stability safety cut-out. This will automatically switch off the halogen heater if it is not in the upright position. Once the halogen heater has been correctly placed in an upright position, it will resume normal operation.

Thermal Cut-out Device

The halogen heater is fitted with a thermal safety cut-out device, built in to prevent it from overheating. Should the halogen heater start to overheat, the thermal safety cut-out system will automatically operate and the heat settings will switch off. If this happens:

1. Switch off the halogen heater using the activated heat setting switch.
2. Check that the halogen heater is unplugged from the mains power supply and allow it to cool for approx. 15 minutes.
3. Clear any blockages present on the vent, being careful not to damage the halogen heater.
4. Plug in and switch on the halogen heater at the mains power supply.

[Caution]: In order to avoid a hazard, due to inadvertent resetting of the thermal cut-out, this halogen heater must not be supplied through an external switching device such as a timer or connected to a circuit that is regularly switched on and off by the utility.

Instructions for Use

Before First Use

1. Check that there is no damage to the halogen heater.
2. Remove the white-capped screws from the bottom of the halogen heater main body using a flat head screwdriver and put them to one side.
3. Feed the power supply cord through the cord clips on the bottom of the base stand; this will keep the power supply cord fixed into position.
4. Fix the base stand onto the halogen heater using the white-capped screws.
5. Position the halogen heater on a flat, stable, heat-resistant surface in an open space, at least 1 metre away from furniture, curtains, or any other flammable materials.

NOTE: When using the halogen heater for the first time, a slight odour may be emitted. This is normal and will soon subside. Allow for sufficient ventilation around the halogen heater.

[Caution]: The halogen heater will only fit one way onto the base stand; do not attempt to force it.

Replacing the Halogen Tubes

Switch off and unplug the halogen heater from the mains power supply before attempting to replace the halogen tubes. It is recommended to have replacement bulbs fitted by a qualified electrician, to avoid damage or injury.

1. Remove each side panel by unfastening the top and bottom screws.
2. Slide back the plastic cover on the clip of the halogen tube that needs to be replaced. Detach the clip from the halogen tube by gently pressing the locking mechanism and pulling the clip away. Repeat for each side of the halogen tube.
3. Gently bend the metal tabs and remove the mica panel from each side of the halogen tube that needs to be replaced.
4. Taking hold of one side of the halogen tube by the plastic end, carefully remove it from the halogen heater. Check that the halogen heater has cooled down sufficiently before attempting to replace halogen tubes. Take care not to drop the halogen tube inside the halogen heater whilst removing.
5. Holding the plastic ends of the replacement halogen tube, carefully insert it into the halogen heater. Do not touch the glass casing as this can reduce the lifespan of the halogen tube. Replace the mica panels over each end of the halogen tube and then secure the metal tabs back into position. Reattach the clip and then slide the plastic cover over the clip for protection. Check that the clip has locked properly by gently pulling on the connection.
6. Fasten each side panel back onto the halogen heater.

NOTE: To purchase replacement halogen tubes, visit www.no1brands4you.com.

Using the 1200 W Halogen Heater

1. Plug in and switch on the halogen heater at the mains power supply.
2. To turn on the halogen heater, select the desired heat output by pressing power switch 1, 2, or 3 to the 'I' position. To operate on a low heat setting (400 W), press one switch. To operate on a medium heat setting (800 W), press any two switches. Press all three switches for the highest heat setting (1200 W).
3. Activate the oscillation function by pressing the oscillation switch to the 'I' position; the halogen heater will begin to turn left and right. To stop oscillation, press the switch to the '0' position.
4. Should the position of the halogen heater need to be changed, switch off and unplug it from the mains power supply. Once cooled, move the halogen heater using the carry handle at the rear, checking that there is sufficient cable length available before moving.
5. Turn off the halogen heater by pressing any active power switches to the '0' position.

[Caution]: Check the halogen heater for damage before each use. Do not use if damaged. Do not use the product for extended periods of time.

Care and Maintenance

Always unplug the halogen heater from the mains power supply and allow to cool sufficiently before performing any cleaning or maintenance. Wipe the halogen heater with a soft, damp cloth and allow to dry thoroughly. Do not use harsh or abrasive cleaning solvents, as these may damage the finish of the halogen heater. Do not immerse the halogen heater in water or any other liquid.

Description of Parts

The heater has a front view and a side view illustrated.

Front View: 1. Main body, 2. Carry handle (located on rear), 3. Oscillation switch, 4. Power switch 1 (for bottom tube), 5. Power switch 2 (for middle tube), 6. Power switch 3 (for top tube), 7. Halogen heating tubes, 8. Reflector (behind halogen heating tubes), 9. Lattice mesh guard, 10. Base stand.

Side View: 11. Cord clips (on base), 12. Removable side panels (each side).

Troubleshooting

Storage

Check that the halogen heater is completely cool before storing in a cool, dry place. Never wrap the cord tightly around the halogen heater; wrap it loosely to avoid causing damage.

Specifications

• Product code: EH0197SWK
• Voltage: 220-240 V ~ 50-60 Hz
• Power: 1200 W

ERP Table

Connection to the Mains

Important

Please check that the voltage indicated on the product corresponds with your supply voltage.

As the colours in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, please proceed as follows:

The wires in the mains lead are coloured in accordance with the following code:

• Blue: Neutral (N)
• Brown: Live (L)
• Green/Yellow: Earth [Earth Symbol]

FOR UK USE ONLY - Plug fitting details (where applicable).

Diagram shows a plug with terminals labeled Live, Neutral, Fuse, and Earth. Wires are shown connected: Brown to Live, Blue to Neutral, Green/Yellow to Earth. Cable grip and outer insulation are indicated.

The wire coloured BLUE is the NEUTRAL and must be connected to the terminal marked N or coloured BLACK.

The wire coloured BROWN is the LIVE wire and must be connected to the terminal marked L or coloured RED.

The wire coloured GREEN/YELLOW must be connected to the terminal marked with the letter E or marked [Earth Symbol].

On no account must either the BROWN or the BLUE wire be connected to the EARTH terminal [Earth Symbol].

Always ensure that the cord grip is fastened correctly.

The plug must be fitted with a fuse of the same rating already fitted and conforming to BS 1362 and be ASTA approved.

If in doubt, consult a qualified electrician who will be pleased to do this for you.

Non-rewireable mains plug

If your appliance is supplied with a non-rewireable plug fitted to the mains lead and should the fuse need replacing, you must use an ASTA approved one (conforming to BS 1362 of the same rating).

If in doubt, consult a qualified electrician who will be pleased to do this for you.

If you need to remove the plug - DISCONNECT IT FROM THE MAINS and then cut it off the mains lead and immediately dispose of it safely. Never attempt to reuse the plug or insert it into a socket outlet as there is a danger of an electric shock.

Guarantee

All products purchased as new carry a manufacturer's guarantee; the time period of the guarantee will vary dependent upon the product. Where reasonable proof of purchase can be provided, Beldray will provide a standard 12 month guarantee with the retailer from the date of purchase. This is only applicable when products have been used as instructed for their intended, domestic use. Any misuse or dismantling of products will invalidate any guarantee.

Under the guarantee, Beldray undertakes to repair or replace free of any charge any parts found to be defective. In the event that an exact replacement cannot be provided, a similar product will be offered or the cost refunded. Any damages from daily wear and tear are not covered by this guarantee, nor are consumables such as plugs, fuses etc.

Please note that the above terms and conditions may be updated from time to time and Beldray recommends that you check these each time you revisit the website.

Nothing in this guarantee or in the instructions relating to this product excludes, restricts, or otherwise affects your statutory rights.

For extended guarantee eligibility, go to guarantee.upgs.com/beldray and register your product within 30 days of purchase.

Find Beldray on Facebook: www.facebook.com/Beldray

Disposal of Waste Batteries and Electrical and Electronic Equipment

This symbol on the product, its batteries, or its packaging means that this product and any batteries it contains must not be disposed of with household waste. Instead, it is the user's responsibility to hand this over to an applicable collection point for the recycling of batteries and electrical and electronic equipment. This separate collection and recycling will help to conserve natural resources and prevent potential negative consequences for human health and the environment due to the possible presence of hazardous substances in batteries and electrical and electronic equipment, which could be caused by inappropriate disposal. Some retailers provide take-back services which allow the user to return exhausted equipment for appropriate disposal.

It is the user's responsibility to delete any data on electrical and electronic equipment prior to disposal. For more information about where to drop batteries, electrical and electronic waste off, please contact the local city/municipality office, household waste disposal service, or the retailer.