itel A50 User Manual
Exploded Diagram Specification
The following table details the components of the itel A50:
| Component Number | Component Name | Component Number | Component Name |
|---|---|---|---|
| 1 | DISPLAY COMPONENTS | 2 | RECEIVER DECORATION |
| 3 | SHELL COMPONENT | 4 | RECEIVER |
| 5 | FRONT CAMERA SILICONE COVER | 6 | FRONT CAMERA |
| 7 | REAR CAMERA | 8 | SIM CARD HOLDER CONDUCTIVE SPONGE |
| 9 | MAIN BOARD | 10 | FRONT CAMERA SUPPORT FOAM MYRA |
| 11 | MAIN BOARD SCREWS | 12 | CAMERA GROUNDING CONDUCTIVE SPONGE |
| 13 | FRONT CAMERA SUPPORT FOAM | 14 | SIM CARD HOLDER |
| 15 | MIDDLE FRAME COMPONENT | 16 | FLASH COVER LENS |
| 17 | MAIN CAMERA LENS | 18 | SHELL SCREWS |
| 19 | COMPOSITE BOARD BATTERY COVER | 20 | FINGERPRINT |
| 21 | REAR AUXILIARY CAMERA | 22 | SPEAKER |
| 23 | BATTERY | 24 | MOTOR |
| 25 | SUB PCBA | 26 | USB SILICONE SLEEVE |
| 27 | COAXIAL LINE | 28 | EARPHONE SILICONE CASE |
| 29 | SIDE KEY FPC | 30 | REAR MAIN CAMERA CONDUCTIVE SPONGE |
| 31 | REAR AUXILIARY CAMERA CONDUCTIVE CLOTH | 32 | REAR SECONDARY CAMERA LENS |
Know Your Phone
Your itel A50 features the following external components:
- 1. Front camera
- 2. Volume + button
- 3. Volume - button
- 4. Power button & side fingerprint sensor
SIM/SD Card Installation
- Ensure your phone is powered off before proceeding.
- Refer to the following visual guide for correct SIM/SD card installation.
[Visual guide for SIM/SD card installation]
Charging the Phone
You can charge your phone using a compatible charger or by connecting it to a computer via a USB cable. Use only itel-approved chargers and cables to prevent potential damage to the phone and to maintain warranty validity.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the device.
Information to the User
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and may radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for assistance.
Specific Absorption Rate (SAR) Information
This mobile phone meets government requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. These standards include a substantial safety margin designed to assure the safety of all persons, regardless of age or health.
The SAR limit for the USA (FCC) is 1.6 W/kg averaged over one gram of tissue. The itel A50 (Model: A667LP, FCC ID: 2AJMN-A667LP) has been tested against this SAR limit. The highest SAR value reported during product certification for use at the ear is 1.491 W/kg, and when properly worn on the body is 0.980 W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used with this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
Operating System: Android™ 14 (Go edition)
Android is a trademark of Google LLC.
