itel T1 Neo User Manual
Product: TWS Earphone
Model: T1 Neo
Brand: itel
Please read this user manual carefully before using the product.
*For safety issue, the product remains low capacity during shipping. Please fully charge the product before initial use!
Product Overview
Right Earbud: ①
Left Earbud: ②
Case Status Indicator: ③
Type-C Charging Port: ④
Earbud Status Indicator: ⑥
Microphone: ⑦
Multi-Function Force Sensor: ⑤
Using Your Earbuds
1. Turn On & Pairing
Earbuds will turn on and enter pairing mode automatically when taken out of the charging case.
Status Indicators:
- Power on: Steady green for 1 second.
- TWS Pairing: Flashing green and red simultaneously on both earbuds.
- BT Pairing: Flashing green and red simultaneously on both earbuds.
- Connected to a device: Flashing blue and red once and then lights off.
Pairing Instructions:
- For itel P36 & P36 Pro LTE, a pairing window will pop up at the first time of connection.
- For other mobile devices, ensure Bluetooth is ON.
Important Notes:
- Make sure the distance of the earbuds and your device is less than 10 meters / 3.3 feet at the first time of connection.
- Earbuds will automatically connect to the last connected device when turned on. The pop-up window will show the earbuds power status.
- Under any abnormal condition, return the earbuds to the charging case and then take out again.
2. Turn Off
The earbuds turn off automatically when placed back into the charging case.
The earbuds will automatically turn off after 3 minutes if no device is connected.
Controls
- Play/Pause: Press the "MFB" button X1.
- Previous track: Tap and hold on the left earbud for 1.5 seconds.
- Next track: Tap and hold on the right earbud for 1.5 seconds.
- Volume down: Tap on the left earbud three times (X3).
- Volume up: Tap on the right earbud three times (X3).
- Activate Voice Assistant: With the earbuds standby mode, long press the "MFB" button for about 3 seconds and release.
- Clear pairing list: With the earbuds power on, and without any devices connected, thrice press the MFB button to clear the pairing information; earbuds will be power off automatically.
- Manually turn on: Long press MFB for about 2 seconds.
- Manually turn off: Long press MFB for about 5 seconds.
Charging Your Earbuds & Case
Earbuds will be charged automatically once they are returned to the charging case.
1. Charging The Earbuds
Earbud Status Indicator:
- Being charged: Steady red.
- Fully charged: Lights off.
2. Charging The Case
Use the included Type-C USB charging cable to charge the case.
Case Status Indicator:
- Being charged: Running lamp first, then the lights will turn on based on the case power level.
- Fully charged: The green light flashes.
- Low battery: The red light is always on.
Important Note: To preserve battery lifespan, fully charge at least once every 45 days.
Basic Product Specifications
Earbuds
- BT version: V5.1
- Weight: 3g (each earbud)
- Talk time: Up to 4 hours
- Music play time: Up to 4 hours
- Battery capacity: 25mAh (each earbud)
- Talk range: 10m/33ft
Charging Case
- Weight: 29g
- Battery capacity: 300mAh
- Charging time: Approx. 3 hours
Package Contents
- True Wireless Half In-Ear Earbud x 2
- Charging Case x 1
- Type-C Charging Cable x 1
Attention
• Use original or certified cables.
• Do not expose to liquids.
• Do not disassemble.
• Avoid dropping.
• Avoid extreme temperatures.
• Do not use the product outdoors during a thunderstorm.
• Do not use any corrosive cleaner/oil to clean.
Considerate Hints
- Do not turn up the volume to a fair high level constantly as this could shorten the service life of this product or impair your hearing.
- When encountering any fault during operation, please cut off the power supply and disconnect the USB cable to prevent further damage to the product or other components.
- The wireless transmission range or connectivity could be affected by low battery power. In that case, please recharge immediately.
Caution
- Use careful with the earphone; excessive sound pressure from earphones and headphones can cause hearing loss.
- Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
- Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
- A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
- The product shall only be connected to a USB interface of version USB 2.0.
- EUT Temperature: 0°C~+45°C (Standalone). 0°C~+40°C (with adapter).
- To prevent possible hearing damage, do not listen at high volume levels for long periods.
- USB cable is shielded.
FCC Compliance Information
Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Information and Statement
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: T1 (FCC ID: 2ADYY-T1) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification properly worn the body is 0.098 W/kg. This device was tested for typical body-worn operations with the back of the handset kept 0 mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 0 mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that does not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 0mm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
EU Declaration of Conformity
Hereby, ITEL MOBILE LIMITED declares that this True Wireless Half In-Ear Earbuds is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
1. Radio equipment: Model: T1 Neo, Product: TWS Earphone, Trade name or Brand: itel, Software/Hardware number: 5.1/V1.0
2. Manufacturer: ITEL MOBILE LIMITED, Address: FLAT 39 8/F BLOCK D WAH LOK INDUSTRIAL CENTRE 31-35 SHAN ME STREET FOTAN NT
3. Declaration of conformity is issued under the sole responsibility of the Manufacturer.
4. Object of the declaration: Model: T1 Neo
5. Conformity: The object of the declaration is in conformity with the relevant Union harmonization legislation: Directive 2014/53/EU (RED).
6. Relevant harmonised standards used:
- Article 3.1a Health: EN 62479:2010
- Article 3.1a Electrical Safety: EN62368-1:2014+A11:2017
- Article 3.1b: ETSI EN 301 489-1 V2.2.3 (2019-11), ETSI EN 301 489-17 V3.2.4(2020-09)
- Article 3.2: ETSI EN 300 328 V2.2.2 (2019-07)
7. Notified Body: Eurofins Electrical and Electronic Testing NA, Inc., Notified Body Number: 0980
8. Accessories and components: User instructions are provided in the User Manual. Software and Hardware versions are specified above.
9. Additional information:
- Equipment can be operated in all Member States without infringing applicable requirements on the use of radio spectrum.
- No restrictions on putting this equipment into service or requirements for authorization of use. Please refer to the User Manual for details.
On behalf of:
Manufacturer: ITEL MOBILE LIMITED
Address: FLAT 39 8/F BLOCK D WAH LOK INDUSTRIAL CENTRE 31-35 SHAN ME STREET FOTAN NT
Place and date of issue: Shenzhen, 2021-12-16
Name, function: Yiting, Luo/Manager
Signature: Yiting. Luo
Home - 传音
