Itel IKP-31 User Manual
Explosion Diagram Specification
| Part Number | Description | Part Number | Description |
|---|---|---|---|
| 1 | FL(G+G+LCM)8HD | 2 | Front cover |
| 3 | CAM FF / AF 5M | 4 | FPC KEY |
| 5 | PCBA MAIN | 6 | Screw M1.4*L4.5*D2.5*H0.5 |
| 7 | Motor | 8 | Side key F |
| 9 | Back cover | 10 | Rear Cam lens |
| 11 | Card holder | 12 | Screw M1.4*L4.5*D2.5*H0.5 |
| 13 | SPK | 14 | Coaxial cable |
| 15 | 4G small board | 16 | Battery |
| 17 | MIC |
A detailed exploded view diagram of the Itel IKP-31 is provided, illustrating the various components and their assembly. The diagram includes numbered parts corresponding to a list of components such as the front cover, camera modules, main circuit board, screws, motor, speaker, battery, and more.
Know Your Phone
This section provides a visual guide to the different parts of the Itel IKP-31 phone:
- 1. USB-C Charging Port
- 2. Earphone jack
- 3. Front camera
- 4. Volume + key
- 5. Volume - key
- 6. Power On/Off
- 7. Microphone
- 8. Speaker
- 9. Memory Card Slot
A diagram shows the phone with numbered indicators pointing to each of these external features.
SIM/SD Card Installation
- Power off the mobile device.
- Refer to the provided illustration for the correct SIM and SD card installation procedure.
An illustration depicts the internal layout of the phone, highlighting the slots for SIM and SD cards.
Charging the Phone
To charge your Itel IKP-31, you can use a compatible charger or connect it to a computer via a USB cable. It is important to use only the Itel charger and cables provided with the tablet, as using other chargers or cables may damage the device and void your warranty.
An illustration shows the USB-C charging port on the phone and a close-up view of the cable being inserted.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- (1) This device may not cause harmful interference.
- (2) This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Information to the user:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement: The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: IKP-31 (FCC ID: 2AJMN-IKP-31) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use when properly worn on the body is 1.180 W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
