Philips TAV2000DB Portable Radio

1 Important Safety Information

Please read and follow these instructions carefully:

• ⚠️ Read these instructions.
• ⚠️ Pay attention to warnings.
• ⚠️ Follow all instructions.
• ⚠️ Do not block ventilation openings.
• ⚠️ Do not install near heat sources like radiators, heaters, ovens, or other heat-producing equipment.
• ⚠️ Keep the device away from sunlight, open flames, or heat.
• ⚠️ The device must not be exposed to dripping or splashing water.
• ⚠️ Place the product on a flat, firm, and stable surface.
• ⚠️ Do not place any danger sources on the device (e.g., containers filled with liquid, lit candles).
• ⚠️ Never place this device on other electrical equipment.
• ⚠️ Use only accessories specified by the manufacturer.
• ⚠️ Never remove the device casing. Refer servicing to qualified personnel. Servicing is required if the product is damaged, the power cord or plug is damaged, liquid has spilled, objects have fallen into the device, it has been exposed to rain or moisture, it does not operate normally, or it has been dropped.
• ⚠️ Batteries (battery pack or installed battery) must not be exposed to excessive heat such as direct sunlight, fire, or similar.
• ⚠️ Risk of explosion if batteries are replaced incorrectly. Replace only with the same battery type.
• ⚠️ Batteries may pose a safety risk during operation, storage, or transport at extremely high or low temperatures, or at low air pressure and high altitudes.
• ⚠️ Risk of explosion if the battery is replaced with an incorrect type.
• ⚠️ Do not replace the battery with an incorrect type that bypasses safety (e.g., certain types of lithium batteries).
• ⚠️ Install all batteries correctly.
• ⚠️ Leaving batteries in an environment with extreme temperatures or low air pressure may result in explosion or leakage of flammable liquid or gas.
• ⚠️ Batteries contain chemicals and must be disposed of properly.
• ⚠️ If you suspect a battery has been swallowed or is lodged anywhere in the body, seek immediate medical attention.
• ⚠️ When replacing batteries, keep both new and old batteries out of reach of children. Ensure the battery compartment is fully closed after replacement.
• ⚠️ If the battery compartment cannot be fully closed, stop using the product and keep it out of reach of children. Contact the manufacturer.
• ⚠️ The device must not be exposed to dripping or splashing water.
• ⚠️ Do not place any danger sources on the device (e.g., containers filled with liquid, lit candles).
• ⚠️ Use the product safely in an environment where the temperature is between 0°C and 45°C.
• ⚠️ To avoid fire risk, the equipment is powered only by an external power source with an output power compliant with PS1 (less than 15W).
• ⚠️ The charger's power output must be between a minimum of 5W (required for the radio equipment) and a maximum of 15W (for maximum charging speed).

2 Portable Radio

Congratulations on your purchase and welcome to Philips! To fully enjoy the support Philips offers, register your product at www.philips.com/support.

Introduction

With this portable radio, you can:

• Listen to DAB (Digital Audio Broadcasting), FM radio, and Bluetooth® music.
• Set two alarms to ring at different times.

What's in the box

Check and identify the contents of the package:

• Main unit
• Type-C charging cable
• Quick start guide
• Safety sheet
• Warranty card

Image description: The package contents include the main radio unit, a USB-C cable, and documentation.

Note: Images, illustrations, and drawings in this user manual are for reference only. The actual product may look different.

3 Getting Started

Always follow the instructions in this section in order.

Charging the Built-in Battery

The portable radio is powered by a built-in rechargeable battery.

Note: The ? icon appears when the battery is low. Please charge the battery as soon as possible.

Connect the Type-C port on the portable radio to the input (5V 2A) using the provided Type-C cable.

Image description: A Type-C cable is shown connecting to the portable radio's charging port.

Note: Please note that your device contains built-in lithium batteries. The charging capacity of lithium batteries will decrease over time due to their discharge characteristics. To ensure the longevity of your device's battery, it is recommended to charge the built-in lithium battery to about 50% every six months when the device is not in use.

Powering On/Off or Switching to Standby Mode

• Press the [power-button] to turn on the device. The radio will turn on to the last selected source.
• Press the [standby-button] to switch the device to standby mode. The time will appear on the screen (if set).

Note: If a Bluetooth device is not connected for more than 15 minutes, or if it is connected but not playing, the radio will automatically switch to standby mode. Press and hold the [power-button] for three seconds in any mode to turn off the device directly. The device screen will turn off.

Adjusting Volume

While listening, turn the knob to adjust the volume.

Adjusting Screen Brightness

You can select different brightness levels or turn off the screen.

1. Press the [menu-button] to access the menu.
2. Turn the rotary knob or press ◀️/▶️ to select [Display], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to select [Backlight level], then press [SELECT] to confirm.
4. Turn the rotary knob or press ◀️/▶️ to adjust the brightness level (High, Medium, Low) on the screen, then press [SELECT] to confirm.
5. Press the [back-button] to exit the menu.

Standby Menu Navigation

When the device is in standby mode, you can access the menu for control options.

1. In standby mode, press the [menu-button] to access the menu.
2. Turn the rotary knob or press ◀️/▶️ to select a menu option, then press [SELECT] to confirm the option or enter a lower menu level.
   • [Display]: Adjust backlight, dimming, and timeout settings.
   • [Alarm]: Set alarms 1 or 2 and alarm settings.
   • [Clock]: Synchronize time, date, and time format.
   • [System]: Adjust system settings.
3. Repeat step 2 if a sub-option is available.
4. Press the [back-button] to return to the previous menu.

4 Setting the Clock

Note: The device will exit the menu if no button is pressed for 30 seconds.

Automatic Clock Setting

1. Press the [menu-button] to access the menu.
2. Turn the rotary knob or press ◀️/▶️ to select [Clock], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to select [Set auto/manual], then press [SELECT] to confirm.
4. Turn the rotary knob or press ◀️/▶️ to select [Auto (DAB/RDS)], then press [SELECT] to confirm.
5. Press the [back-button] to return to the previous menu.

When tuned to a DAB/FM RDS station, the device can automatically synchronize the time broadcast by the DAB/FM RDS station (with CT information).

Manual Clock Setting

1. Press the [menu-button] to access the menu.
2. Turn the rotary knob or press ◀️/▶️ to select [Clock], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to select [Set date&time], then press [SELECT] to confirm.
4. Turn the rotary knob or press ◀️/▶️ to select the hour, then press [SELECT] to confirm. The minutes will flash.
5. Turn the rotary knob or press ◀️/▶️ to select the minutes, then press [SELECT] to confirm.
6. Turn the rotary knob or press ◀️/▶️ to select the month, then press [SELECT] to confirm.
7. Turn the rotary knob or press ◀️/▶️ to select the day, then press [SELECT] to confirm.
8. Turn the rotary knob or press ◀️/▶️ to select the year, then press [SELECT] to confirm. The time is now set.
9. Press the [back-button] to return to the previous menu.

Setting Time Format

1. Press the [menu-button] to access the menu.
2. Turn the rotary knob or press ◀️/▶️ to select [Clock], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to select [Set 12H/24H], then press [SELECT] to confirm.
4. Turn the rotary knob or press ◀️/▶️ to select [12H] or [24H], then press [SELECT] to confirm.
5. Press the [back-button] to return to the previous menu.

Setting Date Format

1. Press the [menu-button] to access the menu.
2. Turn the rotary knob or press ◀️/▶️ to select [Clock], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to select [Set date format], then press [SELECT] to confirm.
4. Turn the rotary knob or press ◀️/▶️ to select [MM-DD-YYYY], [DD-MM-YYYY], or [YYYY-MM-DD], then press [SELECT] to confirm.
5. Press the [back-button] to return to the previous menu.

Clock Style

1. Press the [menu-button] to access the menu.
2. Turn the rotary knob or press ◀️/▶️ to select [Clock], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to select [Clock style], then press [SELECT] to confirm.
4. Turn the rotary knob or press ◀️/▶️ to select [Classic analog] or [Normal digital], then press [SELECT] to confirm.
5. Press the [back-button] to return to the previous menu.

5 Setting Alarms

Setting Alarm Time

Note: Ensure the clock is set correctly.

1. Press the [menu-button] to access the menu.
2. Turn the rotary knob or press ◀️/▶️ to select [Alarm], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to select [Alarm 1 Setup] or [Alarm 2 Setup], then press [SELECT] to confirm.
4. Turn the rotary knob or press ◀️/▶️ to select [Wake up time], then press [SELECT] to confirm. The hour will flash.
5. Turn the rotary knob or press ◀️/▶️ to select the hour, then press [SELECT] to confirm. The minute will flash.
6. Turn the rotary knob or press ◀️/▶️ to select the minute, then press [SELECT] to confirm.
7. If [Once] is selected as the alarm period, use ◀️/▶️ and [SELECT] to set the alarm date.
8. Turn the rotary knob or press ◀️/▶️ to select [Frequency], then press [SELECT] to confirm; the alarm repetition cycle will flash.
9. Turn the rotary knob or press ◀️/▶️ to select the cycle (Once, Daily, Weekly, or Weekend mode), then press [SELECT] to confirm.
10. Turn the rotary knob or press ◀️/▶️ to select [Source], then press [SELECT] to confirm. The alarm source will flash.
11. Turn the rotary knob or press ◀️/▶️ to select (BUZZER, DAB, or FM radio), then press [SELECT] to confirm.

If [DAB] or [FM] is selected as the alarm source (default is BUZZER), the alarm menu will have additional [Source] options. Use ◀️/▶️ and [SELECT] to select the DAB or FM preset radio station number.

11. Press the [back-button] to return to the previous menu.

The corresponding alarm icon ? will appear.

Tip: The device will exit the setting mode after 30 seconds of inactivity. If DAB/FM is selected as the alarm source but no preset station is selected, BUZZER will activate automatically. The alarm will expire after 60 minutes if there is no user interaction.

Activating/Deactivating Alarm Timer

1. Press the [menu-button] to access the menu.
2. Turn the rotary knob or press ◀️/▶️ to select [Alarm], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to select [Alarm 1] or [Alarm 2], then press [SELECT] to confirm.
4. Turn the rotary knob or press ◀️/▶️ to select [On] or [Off], then press [SELECT] to confirm.
5. Press the [back-button] to return to the previous menu.

If the alarm timer is activated, the ? icon will appear. If the alarm timer is deactivated, the icon will appear.

Snooze

1. When the alarm sounds, press the [snooze-button]. The alarm will enter snooze mode and ring again after 10 minutes (default setting).
2. During the snooze period, press ◀️/▶️ to select a different period (in minutes) for the alarm to ring again. (Options: 10, 20, 30, 40, 50, 60 minutes).
3. During the snooze period, press and hold the [snooze-button] or [stop-button] for three seconds to cancel the alarm. The alarm will stop.

Stopping Alarms

When the alarm sounds, press the [snooze-button] to pause the alarm sound and enter snooze mode, or press the [stop-button] to stop the alarm sound.

The alarm will stop, but the alarm settings will remain.

Setting Sleep Timer

This portable radio can automatically switch to standby mode once the sleep time is set.

1. Turn on the device.
2. Press the [sleep-button] to select the sleep time. Press repeatedly to select a different sleep time (15, 30, 45, 60, 90, 120 minutes, or Off).

To deactivate the sleep timer: Repeat the previous steps and set the sleep timer to Off.

6 Listening to DAB Radio

Note: Keep the portable radio away from other electronic devices to avoid radio interference. For optimal reception, pull out the DAB/FM antenna completely and adjust its position.

Selecting DAB Radio Stations

When you select DAB radio mode for the first time, or if the station list is empty, the radio will perform a full scan.

1. Turn on the device.
2. Press the [DAB/FM-button] to select DAB mode. [Scanning...] will be displayed. The radio will automatically scan all DAB stations and play the first available one. The list of stations will appear. The next time you turn on the radio, a new scan will not be performed.
3. Once all stations are found, press ◀️/▶️ to browse the found stations, then press [SELECT] to confirm.
4. To rescan, press [SCAN] for three seconds.
5. Press the [menu-button] to access the DAB menu, then press [SELECT] to enter [Full scan]. Turn the rotary knob or press ◀️/▶️ to select [Yes] (to activate full scan) or [No], then press [SELECT] to confirm.

Manual Tuning

In addition to automatic scanning, you can manually tune the receiver. This can help when adjusting the antenna or adding stations missed during automatic tuning.

1. Press the [menu-button] to enter the DAB menu.
2. Turn the rotary knob or press ◀️/▶️ to select [Manual tune], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to cycle through DAB channels (labeled 5A to 13F), then press [SELECT] to confirm. The device will display the frequency and begin scanning.
4. Press the [back-button] to exit the menu.

Storing DAB Radio Stations

Note: You can manually store up to 20 DAB radio stations.

1. In DAB mode, tune to the desired DAB radio station.
2. Press and hold the number button (1 or 2) for three seconds to directly save the current station to the corresponding preset position. [Preset 1 or 2 stored] will be displayed. The station is now stored in the desired position.
3. In DAB mode, press 1 or 2 to directly select the preset radio station (1 or 2).

Storing and Selecting Favorite Stations

Note: You can store favorite stations on the direct buttons 1 or 2.

1. In DAB mode, tune to the desired DAB radio station.
2. Press and hold buttons 1 or 2 for three seconds to directly save the current station to the corresponding position. [Preset 1 or 2 stored] will be displayed. The station is stored in the desired position.
3. In DAB mode, press 1 or 2 to directly select the preset radio station (1 or 2).

Selecting Preset Radio Station

1. In DAB mode, press the [preset-button].
2. Turn the rotary knob or press ◀️/▶️ to select the preset radio station.

Note: After three seconds, the preset radio station will be confirmed automatically.

Removing Faulty Stations

1. Press the [menu-button] to enter the DAB menu.
2. Turn the rotary knob or press ◀️/▶️ to select [Prune], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to select [Yes] (to remove all faulty stations from the list) or [No], then press [SELECT] to confirm.
4. Press the [back-button] to exit the menu.

DRC (Dynamic Range Control)

DRC compresses the dynamic range of the radio signal, increasing the volume of quiet sounds and decreasing the volume of loud sounds.

1. Press the [menu-button] to enter the DAB menu.
2. Turn the rotary knob or press ◀️/▶️ to select [DRC level], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to select [High], [Low], or [Off], then press [SELECT] to confirm.
4. Press the [back-button] to exit the menu.

Displaying DAB Information

While listening to DAB radio, press and hold for three seconds to display the following information (if available):

• DAB or DAB+
• Station name
• Scrolling text
• Program type (e.g., [NEWS], [SPORT], [POP M])
• Multiplex name
• Channel
• Frequency
• Mode: Transfer rate
• Mode: Channel type
• Signal quality

DAB Menu Navigation

When listening to DAB, you can access the menu for control options.

1. Press the [menu-button] to enter the DAB menu.
2. Turn the rotary knob or press ◀️/▶️ to select a menu option, then press [SELECT] to confirm the option or enter a lower menu level.
   • [Full scan]: Scan and store all available DAB radio stations.
   • [Manual tune]: Manually tune to a specific channel/frequency and add it to the station list.
   • [Prune]: Remove faulty stations from the list.
   • [DRC level]: Adjusts dynamic range compression.
   • [Kitchen timer]: Set the kitchen timer.
   • [Sleep timer]: Set the sleep timer.
   • [Display]: Adjust backlight, dimming, and timeout settings.
   • [Alarm]: Activate/deactivate alarms and set alarm parameters.
   • [Clock]: Synchronize time, date, and set time/date formats.
   • [System]: Adjust system settings.
3. Repeat step 2 if a sub-option is available.
4. Press the [back-button] to return to the previous menu.

Note: The device will exit the menu if no button is pressed for 30 seconds.

7 Listening to FM Radio

Note: Keep the portable radio away from other electronic devices to avoid radio interference. For optimal reception, pull out the DAB/FM antenna completely and adjust its position.

Auto Tuning

1. Press the [power-button] to turn on the device.
2. Press the [DAB/FM-button] to select FM mode.
3. Press and hold ◀️/▶️ for 3 seconds. The portable radio will automatically tune to stations with a strong signal.

Manual Tuning

Press ◀️/▶️ to select the frequency to manually tune the station.

Note: The portable radio's tuning step is 50 KHz. The radio frequency on the screen will increase by 0.05 MHz with each press of ◀️/▶️.

Automatic Scan and Store FM Stations

Note: You can store a maximum of 20 FM radio stations.

In FM mode, press and hold [SCAN] for three seconds. [Auto Scanning...] will be displayed. The radio will automatically scan and store all FM stations, then play the first available station.

Manual Store FM Radio Stations

1. Select an FM radio station in FM mode.
2. Press and hold the number button (1 or 2) for three seconds to activate programming mode. The preset list will appear.
3. Turn the rotary knob or press ◀️/▶️ to select the preset number.
4. Press [SELECT] to store the preset station.
5. Repeat steps 1 to 4 to store more FM radio stations.

Tip: To remove pre-stored stations, store a new station in its place if the preset number exceeds 20.

Store and Select Favorite Stations

Note: You can store favorite stations on the direct buttons 1 or 2.

1. Select an FM radio station in FM mode.
2. Press and hold buttons 1 or 2 (preset number) for three seconds to directly save the current station to the corresponding position. [Preset 1 or 2 stored] will be displayed. The preset number and station frequency will be shown on the screen.
3. In FM mode, press 1 or 2 to directly select the preset radio station (1 or 2).

Select Preset Radio Station

1. In FM mode, press the [preset-button].
2. Turn the rotary knob or press ◀️/▶️ to select the preset radio station.

Note: After three seconds, the preset radio station will be confirmed automatically.

Scan Sensitivity Setting

1. Press the [menu-button] to enter FM mode.
2. Press [SELECT] to enter [Scan setting].
3. Turn the rotary knob or press ◀️/▶️ to select [Strong] (for strong signal stations only) or [All] (all stations), then press [SELECT] to confirm.
4. Press the [back-button] to exit the menu.

Displaying RDS Information

RDS (Radio Data System) is a service that allows FM radio stations to display additional information.

1. Listen to an FM RDS station.
2. Press and hold for three seconds to display the following information (if available):
   • Station name
   • Program type (e.g., [NEWS], [SPORT], [POP M])
   • Time
   • Text
   • Frequency

FM Menu Navigation

When listening to FM, you can access the menu for control options.

1. Press the [menu-button] to enter FM mode.
2. Turn the rotary knob or press ◀️/▶️ to select a menu option, then press [SELECT] to confirm the option or enter a lower menu level.
   • [Scan setting]: Select scan sensitivity (strong signal stations only or all stations).
   • [Kitchen timer]: Set the kitchen timer.
   • [Sleep timer]: Set the sleep timer.
   • [Display]: Adjust backlight, dimming, and timeout settings.
   • [Alarm]: Activate/deactivate alarms and set alarm parameters.
   • [Clock]: Synchronize time, date, and set time/date formats.
   • [System]: Adjust system settings.
3. Repeat step 2 if a sub-option is available.
4. Press the [back-button] to return to the previous menu.

Note: The device will exit the menu if no button is pressed for 30 seconds.

8 Listening to Bluetooth® Music

Note: The operational range between devices is approximately 25 meters (in open space). Compatibility with all Bluetooth® devices is not guaranteed. Obstacles between devices may reduce the range. Keep away from other electronic devices to avoid interference. The device will also turn off if your device goes out of the operational range.

Connecting Bluetooth®

1. Press the [Bluetooth-button] to select Bluetooth mode. [Not Connected] will appear.
2. On your Bluetooth device, turn on Bluetooth, search for, and select [Philips TAV2000DB] to start pairing.

If successfully connected:

• You will hear a signal sound.
• [Connected] will appear.

Disconnecting Bluetooth®

• Switching to another source on the device.
• Disabling the function on your Bluetooth® device.

Alternatively, press and hold the [Bluetooth-button] for three seconds to disconnect the Bluetooth connection. If the connection is successfully disconnected, you will hear a signal sound and [Pairing] will appear.

Pairing Bluetooth® Devices

1. Press the [menu-button] to access the Bluetooth menu.
2. Press [SELECT] to select [Bluetooth pair].
3. Turn the rotary knob or press ◀️/▶️ to select [Yes] (to disconnect the Bluetooth connection and enter pairing mode), then press [SELECT] to confirm.

Clearing Bluetooth® Pairing Memory

1. Press the [menu-button] to access the Bluetooth menu.
2. Turn the rotary knob or press ◀️/▶️ to select [Bluetooth clean], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to select [Yes] to disconnect the current connection or [No] to keep the connection, then press [SELECT] to confirm.
4. Press the [back-button] to exit the menu. [Pairing] will appear.

Playing Music

When playing music on your Bluetooth® device, you can use this device to control music playback.

• Press [SELECT] to pause/resume playback.
• Press ◀️/▶️ to skip to the next or previous track.
• Turn the knob to adjust the volume.

Bluetooth Menu Navigation

When listening via Bluetooth®, you can access the menu for control options.

1. Press the [menu-button] to access the Bluetooth menu.
2. Turn the rotary knob or press ◀️/▶️ to select a menu option, then press [SELECT] to confirm the option or enter a lower menu level.
   • [Bluetooth pair]: Select to disconnect the Bluetooth connection and enter pairing mode.
   • [Bluetooth clean]: Clear Bluetooth pairing records.
   • [Kitchen timer]: Set the kitchen timer.
   • [Sleep timer]: Set the sleep timer.
   • [Display]: Adjust backlight, dimming, and timeout settings.
   • [Alarm]: Activate/deactivate alarms and set alarm parameters.
   • [Clock]: Synchronize time, date, and set time/date formats.
   • [System]: Adjust system settings.
3. Repeat step 2 if a sub-option is available.
4. Press the [back-button] to return to the previous menu.

Note: The device will exit the menu if no button is pressed for 30 seconds.

9 Setting Kitchen Timer

Note: The device will exit the menu if it is in standby mode for more than 30 seconds.

Setting Kitchen Timer

1. Press the [power-button] to turn on the device.
2. Press the [menu-button] to access the menu.
3. Turn the rotary knob or press ◀️/▶️ to select [Kitchen timer], then press [SELECT] to confirm.
4. Turn the rotary knob or press ◀️/▶️ to select [Kitchen timer setup], then press [SELECT] to confirm.

Alternatively, you can enter the kitchen timer by pressing and holding the button.

The hour digits will start flashing.

5. Turn the rotary knob or press ◀️/▶️ to select the hour, then press [SELECT] to confirm. The minute digits will start flashing.
6. Turn the rotary knob or press ◀️/▶️ to select the minute, then press [SELECT] to confirm. The second digits will start flashing.
7. Turn the rotary knob or press ◀️/▶️ to select the second, then press [SELECT] to confirm.
8. Turn the rotary knob or press ◀️/▶️ to select [On/Off], then press [SELECT] to confirm.
9. Turn the rotary knob or press ◀️/▶️ to select [On] (activate) or [Off] (deactivate), then press [SELECT] to confirm.
10. Press the [back-button] to return to the previous menu.

The kitchen timer icon ⏰ will appear.

Note: The kitchen timer will turn off after 60 minutes if there is no user interaction.

Stopping Kitchen Timer Sound

When the kitchen timer sounds, press any button to stop the buzzer.

Resetting Kitchen Timer

1. To reset the kitchen timer, press the [menu-button] to access the menu.
2. Turn the rotary knob or press ◀️/▶️ to select [Kitchen timer], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to select [On/Off], then press [SELECT] to confirm.
4. Turn the rotary knob or press ◀️/▶️ to select [Off], then press [SELECT] to confirm.
5. Press the [back-button] to exit the menu.

Note: The kitchen timer can only be reset when the device is on.

10 Other Features

Selecting Menu Language

1. Press the [menu-button] to access the menu.
2. Turn the rotary knob or press ◀️/▶️ to select [System], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to select [Language], then press [SELECT] to confirm.
4. Turn the rotary knob or press ◀️/▶️ to select the menu language, then press [SELECT] to confirm. Available languages include English, Deutsch, Italiano, Français, Norsk, Dansk, Nederlands, Svenska, Español, Suomi, Polski.
5. Press the [back-button] to return to the previous menu.

Listening via Headphones

Plug headphones into the jack on the back of the device.

Factory Reset

1. Press the [menu-button] to access the menu.
2. Turn the rotary knob or press ◀️/▶️ to select [System], then press [SELECT] to confirm.
3. Turn the rotary knob or press ◀️/▶️ to select [Factory reset], then press [SELECT] to confirm.
4. Turn the rotary knob or press ◀️/▶️ to select [Yes] (to restore all radio settings to factory defaults), then press [SELECT] to confirm. [Restarting...] will be shown on the screen.

11 Product Specifications

Note: Product information is subject to change without prior notice.

Amplifier

• Rated output power: 5 W RMS (THD 10%)

Tuner

• Tuner range (FM): 87.5 ~ 108 MHz
• Tuner range (DAB): 174 ~ 240 MHz (Band III)
• Tuner grid: 50 kHz
• Sensitivity
  • Mono, 26 dB S/N Ratio: < 22 dBf
• Total harmonic distortion: < 10%
• Signal-to-noise ratio: > 50 dBA

Bluetooth

• Bluetooth version: V5.4
• Bluetooth frequency range: 2.4 ~ 2.48 GHz
• Max. e.i.r.p.: 5.37 dBm
• Bluetooth range: 25 m (open space)

General Information

• USB port: 5V 2A
• Lithium battery: 3.65 V / 2600 mAh
• Dimensions (W x H x D): 190 x 111.6 x 91.5 mm
• Weight (main unit): 555 g

12 Troubleshooting

⚠️Warning: Never remove the product casing.

To maintain your warranty, never attempt to repair the device yourself. If you encounter problems while using this device, please review the following notes before seeking service. If the problem persists, visit the Philips website (www.philips.com/support). When contacting Philips, ensure your device is nearby and you can easily read the model and serial number.

No Power

• Ensure the portable radio is fully charged.
• Ensure the USB socket on the portable radio is properly connected.

No Sound

• Adjust the volume on the portable radio.
• Adjust the volume on the connected device.
• Check if your Bluetooth device is within the operational range.

Device Unresponsive

• Restart the portable radio.

Poor Radio Reception

• Keep the portable radio away from other electronic devices to avoid radio interference.
• Fully extend and position the antenna.

Alarm Not Working

• Set the clock/alarm correctly.

Clock/Alarm Settings Erased

• Reset the clock/alarm.
• Replace the backup batteries.

Poor Sound Quality After Connecting via Bluetooth

• Bluetooth signal reception is poor. Move the device closer to the speaker or remove obstacles between them.

[Philips TAV2000DB] Not Found on Your Bluetooth Device for Pairing

• Press and hold the [Bluetooth-button] for three seconds to enter Bluetooth pairing mode, then try again.

Cannot Establish Connection with Bluetooth Device

• Bluetooth function is not enabled on the device. Refer to the user manual of that device to learn how to activate this function.
• The portable radio is not in pairing mode.
• The portable radio is already connected to another Bluetooth device.
• Turn off and try again.

Battery Not Charging Properly or Draining Too Quickly

• Replace the batteries.

1. Open the battery compartment cover on the back of the device and remove the original battery.
2. Insert a battery of the same type (not included in the package).
3. Replace the battery compartment cover.

Rechargeable Li-ion Battery Specifications: Model: TACR5001BA Nominal Capacity: 3.65 V, 2600 mAh, 9.49 Wh Maximum Voltage: 4.2 V Manufacturer: TP Vision Europe B.V., Prins Bernhardplein 200, 1097 JB Amsterdam, The Netherlands.

If you wish to purchase an additional battery, visit: https://www.philips.com/support for more information.

13 Notes & Compliance

Compliance

Any changes or modifications to this device not expressly approved by MMD Hong Kong Holding Limited may void the user's right to operate the product. TP Vision Europe B.V. hereby declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU and UK Radio Equipment Regulations SI 2017 No 1206. The Declaration of Conformity can be found at www.philips.com/support.

This product complies with the European Commission's requirements regarding radio interference.

This product is designed and manufactured with high-quality materials and components that can be recycled and reused. The symbol on the product indicates it should not be disposed of with regular household waste. It should be taken to an appropriate recycling facility. Please follow local regulations and never dispose of the product or rechargeable batteries with household waste. Proper disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

The symbol on the product indicates that the product contains batteries compliant with European Regulation (EU) 2023/1542, which cannot be disposed of with regular household waste. Please inform yourself about the local system for separate collection of electrical and electronic products and batteries. Follow local rules and never dispose of this product or batteries with household waste. Proper disposal of old products and batteries helps prevent negative consequences for the environment and human health.

The Bluetooth® name and logo are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by MMD Hong Kong Holding Limited is under license. Other registered trademarks and trade names belong to their respective owners.