COOSPO BC107 User Manual
All About Passion
Button Functions
Left Button
Short Press: Mark a new lap
Hold for 2 seconds: Power off
(Power on: short press the button)
(Short press in setting mode: exit / return and save the setting)
Mid Button
Short Press: Pause / Continue (Short press to start recording after power on)
Hold for 2 seconds: Save the exercise record and exit the exercise
(Short press in setting mode: enter the current setting / switch the number of digits)
Right Button
Short Press: Page turning
Hold for 2 seconds: Setting mode
(Short press in setting mode: switch setting options / switch the numerical)
Charging
- Please charge the device before first time use.
- Please use DC 5V power adaptor for charging.
- During the charging, the battery icon will flash until fully charged.
Open the rubber cover, connect the device with USB cable to charge.
(Connect to USB DC 5V power adaptor / Computer)
Acquiring Satellite Signals, Time Setting and Auto Backlight
Auto Backlight
This device will automatically calculate the sunrise and sunset times. From half an hour before sunset to half an hour after sunrise, the backlight will be automatically illuminated. During the rest of the time, the backlight will be turned off if no operation is detected for 15 seconds.
Acquiring Satellite Signals
Please ensure the device is outdoors with a clear view of the sky. It typically takes 15-90 seconds to locate satellite signals. Remain stationary while acquiring signals. This device can use a speed sensor or GPS for speed tracking. If the speed sensor is not connected, the device uses GPS for speed tracking. When the sensor is connected, it uses the speed sensor.
Time Setting
The time and date will be calibrated automatically after locating satellite signals when the device is powered on (please set the time zone correctly, refer to the time zone setting chapter) or by connecting the device to the CoospoRide App to sync the time.
Status Icons
- TIME: Sport time
- ALT: Altitude
- DST: Distance
- AST: Ascend Distance
- CAL: Calories
- LAP: LAP
- PWR: Power
- HRM: Heart Rate
- CAD: Cadence
- GRA: Gradient
- ODO: Odometer (Total distance)
- UTC Time zone: UTC Time zone
- MPH: Miles per hour
- KMH: Kilometers per hour
- Temperature: Temperature
- Battery level: Battery level
- No satellite signal: Icon indicating no satellite signal
- Satellite signal level: Icon indicating satellite signal strength (No signal, Weak, Normal, Strong)
- Accessory connecting status: Icon indicating accessory connection status
- Manual pause: Icon indicating manual pause
- Connected with App by BLE: Icon indicating connection with App via Bluetooth Low Energy
- Under exercising: Icon indicating the device is under exercise
- Increased & Decreased: Icons indicating increase or decrease
- Average: Average value indicator
- Maximum: Maximum value indicator
Connecting with ANT+ Sensors
- Please ensure the sensors are in wake-up mode (e.g., the heart rate monitor should be worn properly, and the speed cadence and power meter should be awakened by turning the pedals or wheels).
- Wear it correctly, wake up the heart rate belt.
- The speed cadence and power meter are awakened by turning the pedals or wheels.
- Hold the button to get into setting mode.
- There are 5 settings pages available (P1 ~ P5), press the button to switch to P1.
- Press the button to select to enter.
- The computer automatically searches for ANT+ peripherals and connects after searching.
- Press the button to save the found accessories and return. If no ANT+ accessory is found, the device will return to the previous pages automatically. (When a power device is connected during riding, the computer will display power data first. If no power device is connected, it will display GRA slope data).
(Press button: Switch between P1~P5)
(Save and get back to the last pages; device automatically exits if no device is found in 20 seconds)
Standard Accessories
- Main Device x 1
- Charging Cable x 1
- User Manual x 1
- Standard bike mount x 1
- Rubber pad for standard bike mount x 1
- Big size rubber ring x 2
- Small size rubber ring x 2
How to Install: Standard Mount Installation
- Install the rubber pad onto the mount.
- Tie the mount onto the handlebar with the rubber rings.
- Secure the mount.
- Install the main device onto the mount.
- Rotate the main device by 90 degrees.
- Installation completed.
Setting the Wheel Size
- Hold the button to get into setting mode.
- There are 5 settings pages available (P1 ~ P5), press the button to switch to P2.
- Press the button to select to enter.
- Press the button to select the setting digit, and press the button to set the numbers.
- Press the button to save and exit (Automatically exits in 6 seconds if no operation is detected).
(Select the digit; the selected digit will flash)
(Save and get back; automatically exits if no operation is detected in 6 seconds)
Common Wheel Size and Circumference
| Wheel Size | Circumference (L mm) |
|---|---|
| 12 × 1.75 | 935mm |
| 14 × 1.5 | 1020mm |
| 14 × 1.75 | 1055mm |
| 16 × 1.5 | 1185mm |
| 16 × 1.75 | 1195mm |
| 18 × 1.5 | 1340mm |
| 18 × 1.75 | 1350mm |
| 20 × 1.75 | 1515mm |
| 20 × 1-3/8 | 1615mm |
| 22 × 1-3/8 | 1770mm |
| 22 × 1-1/2 | 1785mm |
| 24 × 1 | 1753mm |
| 24 × 3/4 Tubular | 1785mm |
| 24 × 1-1/8 | 1795mm |
| 24 × 1-1/4 | 1905mm |
| 24 × 1.75 | 1890mm |
| 24 × 2.00 | 1925mm |
| 24 × 2.125 | 1965mm |
| 26 × 1.75 | 2023mm |
| 26 × 1.95 | 2050mm |
| 26 × 2.00 | 2055mm |
| 26 × 2.10 | 2068mm |
| 26 × 2.125 | 2070mm |
| 26 × 2.35 | 2083mm |
| 26 × 3.00 | 2170mm |
| 26 × 7/8 | 1920mm |
| 26 × 1(59) | 1913mm |
| 26 × 1(65) | 1952mm |
| 26 × 1.25 | 1953mm |
| 26 × 1-1/8 | 1970mm |
| 26 × 1-3/8 | 2068mm |
| 26 × 1-1/2 | 2100mm |
| 26 × 1.40 | 2005mm |
| 26 × 1.50 | 2010mm |
| 27 × 1 | 2145mm |
| 27 × 1-1/8 | 2155mm |
| 27 × 1-1/4 | 2161mm |
| 27 × 1-3/8 | 2169mm |
| 27.5 × 1.75 | 2114mm |
| 27.5 × 2.125 | 2174mm |
| 27.5 × 1.5 | 2074mm |
| 27.5 × 1.95 | 2146mm |
| 29 × 2.1 | 2288mm |
| 29 × 2.2 | 2298mm |
| 29 × 2.3 | 2326mm |
| 650 × 35A | 2090mm |
| 650 × 38A | 2125mm |
| 650 × 38B | 2105mm |
| 700 × 18C | 2070mm |
| 700 × 19C | 2080mm |
| 700 × 20C | 2086mm |
| 700 × 23C | 2096mm |
| 700 × 25C | 2105mm |
| 700 × 28C | 2136mm |
| 700 × 30C | 2170mm |
| 700 × 32C | 2155mm |
| 700C Tubular | 2130mm |
| 700 × 35C | 2168mm |
| 700 × 38C | 2180mm |
| 700 × 40C | 2200mm |
Time Zone Setting
- Hold the button to get into setting mode.
- There are 5 settings pages available (P1 ~ P5), press the button to switch to P3.
- Press the button to select to enter (Default time zone: UTC/GMT + 08:00).
- Press the button to select the setting digit, and press the button to set the numbers.
- Press the button to save and exit (Automatically exits in 6 seconds if no operation is detected).
(Select the digit; the selected digit will flash)
(Save and get back; automatically exits if no operation is detected in 6 seconds)
Cycling
Turn on the device, press the button to start an exercise and recording. During cycling, if the speed is 0, the device will pause automatically. If no data is received for speed, cadence, and heart rate for 15 minutes, the device will enter sleep mode. Press the button to resume.
(Press button: Mark a new lap)
(Press button: Switch the display)
(Press button: Pause/continue; Hold button: Stop exercise and save the riding data)
Bluetooth Connection
Compatible with:
- iOS 9.0 version and above, iPhone 4s and above
- Any Bluetooth 4.0 enabled Android device with Android 4.3 and above
- Download CoospoRide from Google Play or the App Store.
- Power on the bike computer.
- Open the CoospoRide App, enter the binding computer step, select the BC107 computer from the device list to bind the device. (The phone needs to have Bluetooth turned on and Bluetooth permissions enabled).
- In the activity page of the App, click on the connected device to enter the record synchronization operation page. (Through authorization to Strava in the App's more settings, computer data can be synchronized to the Strava platform simultaneously).
- Select the record to be synchronized and click Sync. The record on the computer will be deleted automatically after synchronization.
(Bind BC107)
Setting Metric and Imperial Units
- Hold the button to get into setting mode.
- There are 5 settings pages available (P1 ~ P5), press the button to switch to P4.
- Press the button to enter (Default: KMH).
- Press the button to switch.
- Press the button to save and exit (Automatically exits in 6 seconds if no operation is detected).
(Set the KMH/MPH)
(Save and get back; automatically exits if no operation is detected in 6 seconds)
Power Calibration
- Hold the button to get into setting mode.
- There are 5 settings pages available (P1 ~ P5), press the button to switch to P5; it will automatically calibrate.
- Short press the button to recalibrate. The value flashes during calibration and stops flashing after successful calibration.
- After successful calibration, press the button to save and exit (Automatically exits in 20 seconds if no operation is detected).
(Recalibrate)
(Save and get back; automatically exits if no operation is detected in 20 seconds)
GPS Positioning
- GPS searching is automatic after power on. Please start cycling after GPS positioning is successful.
- If you start riding when GPS is not successfully positioned (and a speed sensor is not connected), the speed data (real-time, average, maximum) will be displayed as " ". The rest of the data remains the same.
- Tips: You can stand still for 3-5 minutes to get more connections with satellites for better GPS signal.
(Status indicators: No signal, Weak, Normal, Strong)
(Display for no speed data: " ")
Note: Please ensure you are outdoors when positioning. Bad weather and dense forests may affect GPS signal.
Basic Parameters
| Wireless | ANT+ & Bluetooth |
| Display | FSTN Screen, 2.3 inch |
| Backlight | Yes |
| Locate mode | GPS & BDS |
| Lap Count | Yes |
| Storage Format | .fit |
| Water Resistance | IPX7 |
| Weight | 64g |
| Language | English |
| Battery Capacity | 1000mAh |
| Battery Life | 28 hours for a single use after fully charged |
| Material | PC+ABS+TPU |
| Dimension | 81x54x20.6 mm |
| Accessories Supported | ANT+ peripherals (Heart Rate Monitor, Speed Sensor, Cadence Sensor, Speed and Cadence 2 in 1 Sensor, Power Meter) |
| File Transfer | Bluetooth (Specified App Compatible) |
Attentions
The water resistance level of the bicycle computer is IPX7. It can be used in the rain if you close the protective cover on the back tightly. It is recommended to take down the bicycle computer and put it into a waterproof bag if it rains heavily.
Responsibility Disclaimer
The information contained in this manual is for reference only. The product described above may be subject to alteration due to the manufacturer's continuing research and development plans, without prior announcement.
The manufacturer shall not bear any legal responsibility for any direct or indirect, accidental, or special damages, losses, and expenses arising from or in connection with this manual or the contained product.
