COOSPO BC107 User Manual

Button Function

The COOSPO BC107 features three primary buttons:

• Left Button:
  • Short Press: Mark a new lap.
  • Hold for 2 seconds: Power off the device.
  • When powering on: Short press to turn on the device.
  • In setting mode (short press): Exit/return and save the current setting.
• Mid Button:
  • Short Press: Pause or continue an exercise. If pressing after power on, it starts recording.
  • Hold for 2 seconds: Save the exercise record and exit the exercise.
  • In setting mode (short press): Enter the current setting or switch the number of digits.
• Right Button:
  • Short Press: Page turning.
  • Hold for 2 seconds: Enter setting mode.
  • In setting mode (short press): Switch setting options or switch the numerical value.

Status Icons and Device Display

The device displays various status icons and data points:

Status Icons

Device Display Breakdown

The main display shows:

• TIME: Sport time
• ALT: Altitude
• ODO: Odometer (Total distance)
• DST: Distance
• AST: Ascend Distance
• CAL: Calories
• LAP: Lap number
• PWR: Power
• UTC: Time zone

Standard Accessories

The package includes the following accessories:

• Main Device x 1
• Charging Cable x 1
• User Manual x 1
• Standard bike mount x 1
• Rubber pad for standard bike mount x 1
• Big size rubber ring x 2
• Small size rubber ring x 2

How to Install (Standard Mount)

1. Install the rubber pad onto the mount.
2. Tie the mount onto the bike bar using the rubber rings.
3. Securely tie up the mount.
4. Install the main device onto the mount.
5. Rotate the main device for 90 degrees to lock it in place.
6. Installation is now completed.

Charging

1. Please charge the device before its first use.
2. Use a DC 5V power adapter or computer for charging.
3. During charging, the battery icon will flash until the device is fully charged.

To charge, open the rubber cover on the device and connect it with a USB cable. The device uses a built-in battery. Do not dispose of the product in fire. Ensure you use an adapter that meets the device's rated voltage to prevent damage.

Acquiring Satellite Signals, Time Setting, and Auto Backlight

Auto Backlight

The device automatically calculates sunrise and sunset times. The backlight will brighten half an hour before sunset until half an hour after sunrise. During other times, the backlight turns off if there is no operation detected for 15 seconds.

Acquiring Satellite Signals

Ensure the device is outdoors with a clear view of the sky. Acquiring satellite signals typically takes 15-90 seconds. Remain stationary during this process. The device can use speed sensors or GPS for speed tracking. If a speed sensor is not connected, it defaults to GPS. If a speed sensor is connected, it uses the sensor.

Time Setting

The time and date are calibrated automatically after locating satellite signals when the device is powered on. You can also set the time zone correctly (refer to the time zone setting chapter) or connect the device to the CoospoRide App to sync the time.

Connecting with ANT+ Sensors

Ensure all connected sensors are in wake-up mode. For example, the heart rate monitor should be worn correctly, and speed, cadence, and power meters should be activated by turning the pedals or wheels.

To connect sensors:

1. Hold the [Right Button] to enter setting mode.
2. There are 5 settings pages (P1-P5). Press the [Right Button] to switch to P1.
3. Press the [Mid Button] to select and enter.
4. The computer will automatically search for ANT+ peripherals and connect after the search is complete.
5. Press the [Mid Button] to save found accessories and return. If no ANT+ accessory is found, the device returns to the previous pages automatically. If a power device is connected, power data is displayed first; otherwise, GRA slope data is displayed.

Setting the Wheel Size

1. Hold the [Right Button] to enter setting mode.
2. There are 5 settings pages (P1-P5). Press the [Right Button] to switch to P2.
3. Press the [Mid Button] to select and enter.
4. Press the [Mid Button] to select the digit to be set, then press the [Right Button] to set the numbers.
5. Press the [Mid Button] to save and exit. The device will automatically exit in 6 seconds if no operation is detected.

Common Wheel Size and Circumference

The following table lists common wheel sizes and their corresponding circumferences in millimeters (L mm):

Time Zone Setting

1. Hold the [Right Button] to enter setting mode.
2. There are 5 settings pages (P1-P5). Press the [Right Button] to switch to P3.
3. Press the [Mid Button] to select and enter. The default time zone is UTC/GMT + 08:00.
4. Press the [Mid Button] to select the digit to be set, then press the [Right Button] to set the numbers.
5. Press the [Mid Button] to save and exit. The device will automatically exit in 6 seconds if no operation is detected.

Setting Metric and Imperial Units

1. Hold the [Right Button] to enter setting mode.
2. There are 5 settings pages (P1-P5). Press the [Right Button] to switch to P4.
3. Press the [Mid Button] to enter. The default unit is KMH.
4. Press the [Right Button] to switch between units.
5. Press the [Mid Button] to save and exit. The device will automatically exit in 6 seconds if no operation is detected.

Power Calibration

1. Hold the [Right Button] to enter setting mode.
2. There are 5 settings pages (P1-P5). Press the [Right Button] to switch to P5; the device will automatically calibrate.
3. Short press the [Mid Button] to recalibrate. The value will flash during calibration and stop flashing upon successful calibration.
4. After successful calibration, press the [Mid Button] to save and exit. The device will automatically exit in 20 seconds if no operation is detected.

GPS Positioning

GPS searching is automatic after powering on. Please start cycling only after successful GPS positioning.

If you begin riding before GPS positioning is successful (e.g., speed sensor not connected), speed data (real-time, average, maximum) will be displayed as "--.--". Other data remains unchanged.

Tips: Stand still for 3-5 minutes to establish more connections with satellites for a better GPS signal.

Signal strength indicators:

• [No Signal]: No signal
• [Weak Signal]: Weak signal
• [Normal Signal]: Normal signal
• [Strong Signal]: Strong signal

Note: Ensure you are outdoors for positioning. Adverse weather conditions and dense forests can affect GPS signal reception.

Cycling

Turn on the device and press the [Mid Button] to start an exercise and recording. During cycling, if the speed is 0, the device will pause automatically. If no data for speed, cadence, or heart rate is received for 15 minutes, the device will enter sleep mode. Press the [Mid Button] to resume.

Controls during cycling:

• Press [Mid Button]: Pause/continue exercise.
• Hold [Mid Button]: Stop exercise and save the riding data.
• Press [Right Button]: Switch the display.
• Press [Left Button]: Mark a new lap.

Bluetooth Connection

App Download and Compatibility

1. Download the CoospoRide app from the Google Play Store or Apple App Store.

Compatible with:

• iOS 9.0 version and above, iPhone 4s and above.
• Any Bluetooth 4.0 enabled Android device with Android 4.3 and above.

Binding the Device

1. Power on the bike computer.
2. Open the CoospoRide App and navigate to the binding computer step.
3. Select the BC107 from the device list to bind it. Ensure Bluetooth is enabled on your phone and that the app has Bluetooth permissions.

Data Synchronization

1. In the App's activity page, click on the connected device to access the record synchronization page.
2. Through authorization to Strava in the App's more settings, computer data can be synchronized to the Strava platform simultaneously.
3. Select the record to be synchronized and click 'Sync'. The record on the computer will be automatically deleted after synchronization.

Basic Parameters

Attentions

The bicycle computer has a water resistance level of IPX7. It can be used in the rain if the protective cover on the back is tightly closed. For heavy rain, it is recommended to remove the bicycle computer and place it in a waterproof bag.

Responsibility Disclaimer

• The information in this manual is for reference only. The product described may be subject to alteration due to the manufacturer's ongoing research and development plans, without prior announcement.
• COOSPO shall not bear any legal responsibility for any direct or indirect, accidental, or special damages, losses, or expenses arising from or in connection with this manual or the contained product.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

IC Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Product Disposal and Safety

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Contact your local government or a retailer for additional information.

• Do not open or modify the product.
• Do not disassemble or attempt to service this product.
• This product is safe under normal and reasonably foreseeable operating conditions.
• If the product is operating improperly, contact COOSPO support.
• The product must be returned to the manufacturer for any service or repair.