Speco HT7246T1 HD-TVI 2MP Intensifier Outdoor Dome Camera

Special Features

• Sony 1/2.9 inch 2.1MP Exmor CMOS Sensor
• 2.7~12mm DC IRIS Varifocal Lens
• Supports image resolution up to 1920 x 1080P @ 30fps
• Wide Dynamic Range (15fps)
• Full OSD operation through on-board control and UTC
• 2D & 3D noise reduction
• SENS-UP (Digital Slow Shutter)
• Privacy masking (16 zone)
• Dynamic Motion Detection (4 zone)
• Defog
• Surge Protect (DC 2KV / Video 3KV)
• Tool-free 3-Axis mounting
• IP67 Weatherproof
• 12VDC/24VAC Dual Input
• Built-in Heater

Dear Customers

By selecting this product, you have decided to use a professional device that guarantees highest quality and reliability. Speco Technologies thanks you for your confidence and kindly asks you to read the following instructions carefully before installation and operation in order to take full advantage of all quality features regarding this product.

Important Safety Information

CAUTION: [⚡] RISK OF ELECTRIC SHOCK. [?] DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, [?] DO NOT REMOVE THE COVER (OR BACK). [?] NO USER SERVICEABLE PARTS INSIDE. [⛑️] REFER SERVICING TO QUALIFIED PERSONNEL.

The lighting flash with an arrowhead symbol [⚡] within an equilateral triangle is intended to alert the user to the presence of non-insulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle [❗] is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Information

This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at their own expense.

WARNING: Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.

CAUTION: To prevent electric shock and risk of fire hazards:

• Do NOT use power source other than that specified.
• Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should conform to all local codes.

1. Precautions

• Please read the manual carefully before installation to ensure correct setup and best picture quality.
• Keep the manual in good condition for future reference and service application.
• Installation and services should only be carried out by authorized personnel according to local safety regulations.
• If any liquid or solid matter gets into the housing, immediately disconnect the camera from power supply and have it checked by an authorized dealer before reusing.
• Avoid installing the camera at extremely hot or cold places.
• Do not attempt to dismantle the camera if you are not a certified person.
• To avoid electric shock, never remove screws or covers. There are no user-serviceable parts inside. All maintenance should be carried out by qualified personnel.
• Avoid installing the camera in places with high humidity.
• Avoid installing the camera in places exposed to gas or oil.
• Keep the top glass of the lens clean at all times for the best picture quality. Be careful not to stain it with fingerprints.
• Do not face the camera directly towards sunlight or sunlight reflecting areas, as this may damage the CMOS sensor.
• Take special care to protect the unit from dangerous drops or external shocks during transportation or handling.
• Never touch the camera with wet hands, as it may cause electric shock.
• Do not expose the camera to radioactivity, as it can cause serious damage to the CMOS sensor.

2. Limitation of Liability

This publication is provided "AS IS" without warranty of any kind, either express or implied, including but not limited to, the implied warranties of merchantability, fitness for any particular purpose, or non-infringement of the third party's right. This publication could include technical inaccuracies or typographical errors. Changes are added to the information herein at any time for the improvements of this publication and/or the corresponding product(s).

3. Disclaimer of Warranty

In no event shall the seller be liable to any party or person, except for replacement or reasonable maintenance of the product, for cases including, but not limited to:

• Any damage and loss, including without limitation, direct or indirect, special, consequential or exemplary, arising out of or relating to the product.
• Personal injury or any damage caused by inappropriate use or negligent operation by the user.
• Unauthorized disassembly, repair, or modification of the product by the user.
• Inconvenience or any loss arising when images are not displayed, due to any reason or cause, including any failure or problem of the product.
• Any problem, consequential inconvenience, or loss or damage arising out of a system combined with third-party devices.
• Any claim or action for damages brought by any person or organization being photogenically subject, due to violation of privacy, with the result that the surveillance camera's picture, including saved data, becomes public or is used for purposes other than surveillance.

4. Package Contents

The package includes:

• [?] Camera x 1
• [?] Manual x 1
• [?] Drilling template x 1
• [?] Tapping screws x 3
• [?] Plastic anchor x 3
• [?] L-Wrench x 1

For the Junction Box, the package includes:

• [?] Junction Box x 1
• [?] Tapping Screws (Ø4 x 1.18in) x 4
• [?] Plastic Anchor x 4
• [⚪] Silicone Template x 1
• [?] Machine Screw PH (M4 x 0.47in) x 3
• [?] Chameleon Cover x 1
• [?] Cable DC Jack x 1
• [?] Cable BNC Jack x 1
• [?️] Desi Pak x 1
• [?] Ferrite Core x 1

5. Installation

5-1. 3-Axis Adjustment

The camera features a tool-free 3-Axis mounting mechanism for perfect tri-axis adjustment:

• [?] Panning axis up to 345°
• [?] Tilting axis up to 85°
• [?] Rotation axis up to 180°

All adjustments are quick and easy by hand, requiring no tools.

5-2. How to Install on the Ceiling

The installation process involves the following steps:

1. Paste a [?] Drilling Template on the ceiling or wall and drill screw points for installation.
2. Fix the Surface Mounting Base using the provided [?] Tapping Screws.
3. Fix the Flush mount Base onto the Surface Mounting Base.
4. Turn the [?] Camera Assembly to the desired direction.
5. Turn the dome and shield cover to the camera direction.
6. Fix the Dome Cover Assembly to the Flush mount Base using the [?] Screw and [?] L-Wrench.

Connection points include DC Power Jack, BNC Female for TVI, and BNC Female for CVBS.

Junction Box Installation

Installation involves attaching the camera assembly to the junction box using machine screws, with the ceiling tile, drilling template, plastic anchors, tapping screws, and L-wrench used for mounting the junction box itself.

5-3. Application of TVI Output

Connect the camera's TVI output via coaxial cable (5C/3C) to a TVI DVR, and then to a Monitor.

6. Function and Operation

6-1. On Screen Display (On-board Control and UTC)

The camera features an On Screen Display (OSD) menu for configuration, accessible via on-board controls and UTC (Up-the-Coax) communication. The menu structure includes:

• PRESET MENU: Options like INDOOR, OUTDOOR, LOW LIGHT, HALLWAY, LOBBY, ELEVATOR.
• SETUP:
  • LENS: DC, MANUAL
  • EXPOSURE: BRIGHTNESS, SHUTTER, WHITE BAL ([AUTO]/[MANUAL], AWB, AWC-SET), BACKLIGHT ([BLC]/[HLC]), INTENSIFY AGC, WDR.
  • IMAGE: DNR ([LOW]/[MEDIUM]/[HIGH]), SHARPNESS, GAMMA, COLOR GAIN, MIRROR, FLIP, ACE, DEFOG.
  • SYSTEM: ANALOG HD, COLOR BAR, FREQ, CAM TITLE, IMAGE RANGE, COLOR SPACE, HEATER, RESET, LANGUAGE, MOTION ([ON/OFF]), FRAME RATE.
• RETURN and EXIT options are available throughout the menu.

7. Troubleshooting

If problems occur during operation, consult the following checklist. If the problem persists, contact the agent where the product was purchased.

8. Dimensions

The camera has a diameter of approximately Ø130mm and a height of 3.89 inches. The junction box has a diameter of approximately Ø130mm and a height of 5.7 inches. The mounting hole circle diameter (P.C.D.) is Ø121mm.

9. Specifications

Specifications are subject to change without prior notice for better improvement.

Federal Communications Commission (FCC) Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Responsible Party:

Speco Technologies
200 New Highway
Amityville, NY 11701
www.specotech.com