Blaupunkt ROME 910 RM Roof Monitor
Operating and Installation Instructions
Manufactured by Blaupunkt, established 1924 Germany.
Important Safety Information
Safety Notes
This roof monitor is manufactured according to established safety guidelines. However, dangers may still occur if the safety notes in this manual are not observed. This manual is intended to familiarize the user with the roof monitor's important functions. Read this carefully prior to using the monitor. Keep this manual in an easily accessible location. In addition, observe the instructions of the devices used in conjunction with this roof monitor.
Attentions and Precautions
- Protect power lines from damage (folding, tangling, stretching, bending, pulling, or heating).
- Fasten seat belts when watching from the rear seat.
- Do not apply heavy pressure on the device or drop it. Heavy impact may break the LCD or the entire device.
- Incorrect operation may cause casualty due to electric shock or endanger others and properties.
- Wiring and installation should be performed by experienced and professional technicians.
- Fasten leads correctly to prevent loose screws and rails.
- Turn down the sound volume before shutting down the device to prevent hearing damage.
- Regularly clean and check the connecting part of the power line to prevent dust or dirt from covering the power supply. Do not cover or block vent holes, which may lead to fire when overheating.
- Device position should not restrict driver's movement or distract the driver. To prevent accidents and injuries, position the device away from the driver, such as the steering wheel, shift lever, handbrake areas, or front windshield area. The device may cause injury in case of braking if not installed correctly.
Safety Guidelines
- Use only a rated voltage fuse box (2A) to prevent damage to the device.
- Use only specified wiring to avoid damage to the power supply or fire.
- Pay attention to electric shock hazards.
- Unauthorized disassembling, repair, or modification may void the warranty. Consult an authorized Blaupunkt reseller for more information.
- Immediately disconnect the power supply in case of smoke appearing or any abnormal sound to prevent fire or electrical shock.
- Keep the device in a cool and dry place to prevent fire, electric shock, discolouration, and deformation.
- Do not touch the product or the power plug after a thunder event to prevent electric shock.
Disclaimer
Blaupunkt shall not be liable for any direct, indirect, punitive, incidental, or consequential damages to property or life arising out of or connected with the use or misuse of its products.
USA & CANADA: This product is not intended for sale in the United States and Canada. If purchased in the U.S. or Canada, this product is purchased on an "as-is" basis. No warranty, whether expressed or implied, is provided in the U.S. or Canada.
Structure and Remote Control
Function Diagram
The roof monitor unit features the following components:
- 1. Remote Control Receiver: Located on the unit for receiving signals from the remote.
- 2. Dome Light Switch: Controls the interior dome light. Options include: LEFT to turn off, MIDDLE for auto setting, and RIGHT to turn on.
- 3. Screen Lock: Function to lock the screen.
- 4. LED Dome Light: Integrated interior lighting.
- 5. Power Signal Line Connecting Port: Port for connecting the power and signal lines.
- 6. LCD Display Panel: The main screen of the monitor.
Remote Control Key Functions
The remote control provides access to all monitor functions:
- 1. VIDEO [VIDEO/SELECT]: Selects between AV1 and AV2 input sources.
- 2. MENU [MENU]: Accesses the settings menu to adjust brightness, colors, and contrast.
- 3. VOL+ [VOL+]: Increases the audio volume.
- 4. MODE [MODE/SELECT]: Selects display results or modes.
- 5. VOL- [VOL-]: Decreases the audio volume.
- 6. POWER [POWER]: Switches the monitor on or off.
Functions and Specifications
Settings Menu
Using the remote control, press MENU until the desired setting appears, then use VOL+ or VOL- to adjust.
| Setting Category | Value |
|---|---|
| Menu | English (Default), Chinese, Japanese |
| Display Ratio | 16:9 (Default), 4:3 |
| Screen Rotate | LU, RU, LD, RD (Default) |
| Reset | Restore default setting |
| Brightness | 0~100 (50 Default) |
| Contrast | 0~100 (50 Default) |
| Colour | 0~100 (50 Default) |
Signal Display
The monitor displays either the selected input signal or a "No Signal" message.
- With Signal (AV1/AV2): Shows the input source (e.g., AV 1) and the Blaupunkt logo.
- Without Signal: Displays "No Signal".
Specifications
- Screen: 10.1" Fixed panel IPS Screen with white LED dome light.
- Coating: Built-in anti-glare (AG) screen coating.
- Resolution: 1024 x 600 (WSVGA).
- Viewing Angle: Up 50°, Down 70°, Left 70°, Right 70°.
- Flip Down Angle: Adjustable from 0° to 180° for safety purposes.
- Voltage / Current: 12V DC / 1A (monitor), 12V DC / 0.3A (room light).
- Power Consumption: Approximately 15W.
- Input: AV1/AV2.
- Operating Temperature: 0°C to 50°C.
- Storage Temperature: -10°C to 60°C.
- Included Accessories: Remote controller, power signal cord, rubber plug.
- Dimensions: 316mm (Length) x 241mm (Width) x 33 mm (Height).
- Weight: 1.7kg.
Troubleshooting
If problems occur, consult the following solutions. Contact an authorized Blaupunkt dealer if the problem persists.
| Problem | Possible Causes | Solutions |
|---|---|---|
| Unable to start up | The car key is not inserted into the ignition; ignition is off. Power Cable is not inserted into the main body. Burnt power fuse. Drained car battery. |
Insert the car key and turn on the ignition. Insert the power cable. Replace it with a new fuse. Charge or replace the car battery. |
| Dim screen or black-&-white screen while playing video | Brightness, contrast ratio, and color values are excessively adjusted. | Ensure brightness, color, and contrast ratio values are in normal range. |
| Remote control is not working or does not work properly | The battery is low or empty. Remote is not facing the operated unit. Remote's signal detector is facing light interference such as sunlight or car light. |
Replace with fresh batteries. Be sure to point it directly to the remote sensor on the operated unit. Reduce exposure to direct sunlight or other bright light. |
Wiring Diagram
The wiring diagram illustrates the connections for the monitor:
Connections to the Monitor Unit:
- R (Red wire): Connects to +12V power.
- B (Black wire): Connects to Ground.
- G (Yellow wire): Signal detection for the dome light.
- Y (Yellow wire): Video Input 1, typically via RCA port to connect to GPS, DVR, or other devices.
- Y (Yellow wire): Video Input 2.
Additional Power Connections:
- R (Red wire): Spare parts power. Connect this line when the engine switch is on the ACC position.
- B (Black wire): Ground. Ensure this grounding is connected to a metal part of the vehicle's body in good condition.
Accessories Included
The product package includes the following accessories:
- Roof Monitor unit
- Power Signal Cord
- Rubber Plugs (available in 'Without Gap' and 'With Gap' types for installation)
- Remote Control
- User Manual
Installation Instructions
Follow these steps for installing the roof monitor:
- Separate the mounting stand from the main unit by removing the four screws.
- Determine the desired position for the unit in the middle of the ceiling, ensuring equal measurements on both sides. Mark this position and carefully cut out the marked ceiling carpet.
- Align the elongated mounting holes on the stand with the corresponding mounting holes on the vehicle's ceiling.
- Select an appropriately sized screw for installation. Install the stand securely. Before tightening the screws, ensure any wire rods within the wire holes are pulled out.
Installation Kit Details:
The installation kit includes the main body of the monitor, a power signal line to connect to the display, and screw caps. Pay attention to the correct direction when inserting the power signal line into the display. Rubber plugs are provided for mounting, with options for 'Without Gap' and 'With Gap' installations.
