Blaupunkt ROME Series Car Monitors

Safety Notes & Attention

This device has been manufactured according to established safety guidelines. However, dangers may still occur if the safety notes in this manual are not observed. This manual is intended to familiarize the user with the important functions of the device. Read this carefully, prior to using the product. Keep this manual in an easily accessible location. In addition, observe the instructions of other devices used in conjunction with this device. Do not dismantle or modify the device. Installation and repairs, if necessary, should be performed by a specialist. Unauthorized installation, disassembly, or modification may result in unit malfunctions and void of warranty.

Attention:

• The User Interface (UI) displayed in the manual is sourced from various Head Unit models. This approach aims to enhance user experience by providing guidance that caters to navigating different monitors.
• Select a mounting location that ensures the driver's visibility is not obstructed in any circumstances and prevents injuries to drivers and passengers during emergency braking or accidents.
• Prior to fitting the unit into the mount, verify proper wire connections and ensure the unit functions correctly. Refrain from touching the unit during a lightning flash, as there is a risk of electric shock.
• Avoid applying or dropping any pressure on the front panel of your video monitor.
• Exercise caution to avoid damaging vehicle components while drilling holes for the mount.
• This unit is suitable for car rooftop placement. Vehicles may vary from the provided description; consult an authorized Blaupunkt dealer or the vehicle's manufacturer if the information does not align with your specific installation requirements.
• Avoid overloading the cigarette lighter charger with more than one device at a time.
• Exercise special care when dealing with liquids in your vehicle. In the event of any spills on the equipment, safely pull over to the side of the road and switch off the ignition to disconnect or gently wipe the affected areas with a towel. Refrain from using the equipment until all liquids have either dried up naturally or until a qualified technician at a service center has inspected the equipment. Failure to do so may lead to significant harm or hazards.
• The device is designed for 12V vehicle and it does not record video.
• Do not install this unit near a heater outlet. Avoid covering or obstructing heater ducts or vents, as this may pose a fire hazard or risk of electric shock.
• Use only a lightly damped cloth to cleanse the screen, ensuring it is dampened with purified water. Before wiping, ensure excess water is wrung out from the cloth. Avoid the use of cleaners or chemicals on the screen. In many instances, a dry cloth will suffice for cleaning purposes.
• Extended periods of monitor use without the engine running may result in draining the vehicle's battery charge.
• Exclusively use the parts included with the unit.

Disclaimer:

• Blaupunkt is not liable for any loss or damage caused or resulting from unauthorized disassembly or modification to the product.
• Under no circumstances shall Blaupunkt be held liable for any direct, indirect, punitive, incidental, or special consequential damages, whether related to property or life, arising out of or connected with the use or misuse of Blaupunkt products, including but not limited to issues of improper storage.
• USA & CANADA: This product is not intended for sale in the United States and Canada. If acquired in the U.S. or Canada, it is obtained on an "as-is" basis. No warranty, whether express or implied, is provided in the U.S. and Canada.
• This manual may be updated from time to time without any notice. Visit www.blaupunkt.com for more info.

Key Functions

Diagram showing the underside of a Blaupunkt roof monitor. Numbered callouts indicate: 1. Roof monitor bottom cover, 2. On/off button / Function button, 3. Micro SD slot, 4. USB slot, 5. LCD display.

Remote for ROME 1140M RM / ROME 1156M RM

Buttons:

• 1: Power On/Off/Screen saver
• 2: Volume -
• 3: OK
• 4: Left
• 5: Return
• 6: Home
• 7: Mouse Controller
• 8: Previous
• 9: Next
• 10: Mute
• 11: Volume +
• 12: Up
• 13: Right
• 14: Down
• 15: Setting

Remote for ROME 1140A RM / ROME 1156A RM

Buttons:

• 1: Power On/Off
• 2: Monitor up
• 3: Play/Pause
• 4: Page up
• 5: Left
• 6: Page down
• 7: Return
• 8: Previous
• 9: Next
• 10: Delete
• 11: Monitor down
• 12: OK
• 13: Right
• 14: Setting
• 15: Volume +
• 16: Volume -
• 17: Mouse controller On/Off

Remote for ROME 1156A TYAL / ROME 1156M TYAL

Buttons:

• 1: Power On/Off
• 2: Monitor up
• 3: Play/Pause
• 4: Page up
• 5: Left
• 6: Page down
• 7: Return
• 8: Previous
• 9: Next
• 10: Delete
• 11: Monitor down
• 12: OK
• 13: Right
• 14: Setting
• 15: Volume +
• 16: Volume -
• 17: Mute

Specifications

Included Accessories:

Illustration of included accessories: four long screws, a wire harness with connectors, three different remote controls (labeled for specific models), and three pairs of colored roof monitor bottom changeable covers (beige, black, blue).

Installation

For ROME 1156A TYAL / ROME 1156M TYAL (Made for Toyota Alphard, year 2018 - 2023)

1. Remove the original car roof monitor.
2. Install the iron plate to the crossbeam of the car by screwing these 4 holes.
3. Pull the cables (HDMI-in, Power Cable) out from the wire hole of the iron plate.
4. Screw the entire device to the iron plate.

For ROME 1140M RM, ROME 1140A RM, ROME 1156M RM, ROME 1156A RM

1. Separate the iron plate from the main unit by removing the 4 screws.
2. Mark the position of the unit in the middle with similar place measurement on each side. Cut the marked ceiling carpet out.
3. Pull the cable (HDMI-in, Power Cable) out from the wire hole of the iron plate before screwing the entire device to the rooftop.
4. Choose a suitable size of screws to install the iron plate on the rooftop.

Changing Monitor Covers

1. Remove the existing monitor's cover. Ensure to pull out the sides of the cover simultaneously to prevent damage.
2. Select the preferred changeable cover colours and align the buckle on the left cover with the left groove of the monitor, then attach the rest of the cover on the monitor carefully.
3. Ensure no gaps are between the edges of the cover and the monitor by flattening the cover.

Operations

Home Page:

Screenshot of the Blaupunkt monitor's Home Page displaying the time (14:38) and icons for Movie, Picture Viewer, Music, Video, Wireless display, File Manager, Video Input, Apps, and Settings.

Function Setting

Press Settings ⚙️ to adjust the device settings.

Screenshot of the 'Function Setting' menu showing options like Network & internet, Bluetooth, Apps & notifications, Ambient light, Quick Settings, and Display.

Music Playback

Select Music ? icon on the Home Page to playback media that are connected via local device SD card or USB.

Video Playback

Select Video ▶️ icon on the Home Page to playback media that are connected via local device, SD card or USB.

Screenshot of the 'Video Playback' interface showing file navigation options (Local device, USB, ALL) and media types (Movies, Pictures).

Documents Manager

Select File Manager ? icon to manage documents playback media that are connect via local device, SD card or USB.

Screenshot of the 'File Manager' interface displaying storage information (USB 10.47 GB / 16.00 GB) and file categories (Video, Movie, MusicPlayer, Picture Viewer, Video Input, File Manager).

HDMI Video Input

Select Video Input ? icon to watch videos that are connected via HDMI or AV video input.

Icon representing HDMI video input, showing a connection from a source device to the monitor.

Mirrorlink

Select Wireless Display ? icon to setup mirrorlink from the monitor to the smartphone. (Subject to smartphone setting support)

Screenshot of the 'Mirrorlink' setup screen showing options for Android MiraCast and Apple AirPlay, with fields for device names and Help buttons.

• Android: Active Wireless Miracast by connecting smartphone's Wi-Fi to the monitor's Wi-Fi.
• Apple: Ensure to connect the monitor to the smartphone's hotspot. Then open Airplay to connect to CastE8t.

Other Applications

Select Apps ? icon to manage other applications and settings.

Wiring Diagram

Wiring diagram for the Blaupunkt roof monitor. It shows connections for HDMI Video-In, ACC, B+, GND, Audio R Out, Audio L Out, and Video-In. A note explains the connection of the B+ (yellow) connector to the red wire slot on the car's terminal.

Troubleshooting

If any of the following problems occur, please refer to the Troubleshooting section for potential solutions. If the problem persists, seek assistance from an authorized Blaupunkt dealer.

Product Information

Model Numbers and Part Numbers:

• ROME 1140M RM: 1 105 24 003 33 01
• ROME 1140A RM: 1 105 24 004 33 01
• ROME 1156M RM: 1 105 24 005 33 01
• ROME 1156A RM: 1 105 24 006 33 01
• ROME 1156M TYAL: 1 105 24 007 33 01
• ROME 1156A TYAL: 1 105 24 008 33 01

Blaupunkt Car Entertainment - Asia Pacific Competence Centre