VEVOR Paddle Board Pump

Product Introduction

The VEVOR HT-708 is an intelligent DC electric pump featuring a preset pressure LED screen display. It is designed to inflate various items such as inflatable tents, inflatable beds, canoes, cars, bicycles, and balls. The pump also includes a deflation function, allowing users to empty air from inflatable products for easier folding and storage.

Product Parameters

List of Accessories

Please verify the following accessories are included before use. Contact local service agents if any are missing.

• Air pump
• Plastic hose
• Braided hose
• Instruction Book
• Sealing ring

Details of Accessories: The document shows images of the air pump, plastic hose with multiple nozzle attachments, braided hose, instruction book, and a sealing ring.

Component Identification

The VEVOR HT-708 pump has the following components:

Inflation Operation

To operate the pump, press the Scene switch button [M] to select one of the six inflatable scenes:

• Free mode: adjustable range: 0.5-20 PSI ?️
• SUP mode: default 15 PSI, adjustable range: 10-20 PSI ?
• Tent mode: default 6 PSI, adjustable range: 3-10 PSI ⛺
• Air bed mode: default 0.5 PSI ?️
• Car mode: default 2.5 BAR, adjustable range: 1.7-2.75 BAR ?
• Basketball mode: default 8 PSI, adjustable range: 4-16 PSI ?

SUP Inflation

Step 1: Connect the flexible conduit adaptor of the hose to the air pump's inflation inlet and twist clockwise to secure it (Refer to Figure 1).

Step 2: Connect the other end of the hose to the appropriate air nozzle for the air bag (Refer to Figure 2) and insert the inflation valve of the air bag. Turn clockwise to fix it (Refer to Figure 3).

Step 3: Plug the cigarette lighter plug into the 12V DC socket (Refer to Figure 4). The display will illuminate.

Step 4: Press the Scene switch button [M] to select the desired inflatable scene.

Step 5: Use the BAR unit button or PSI unit button to select your desired pressure unit.

Step 6: Use the pressurizing button [+] or decompressing button [-] to set the target pressure. The pressure range is 0 to 20 PSI (1 PSI = 0.0689 BAR = 6.89 KPA).

Step 7: Press the On/Off button [▶️/⏹️] to begin inflation (Refer to Figure 5).

During Inflation: You can adjust pressure using the [+] or [-] buttons, switch units with BAR/PSI buttons, and press the On/Off button [▶️/⏹️] to stop.

Car Inflation

Step 1: Connect one end of the braided hose's fixed head to the air pump inflation port and tighten clockwise (Refer to Figure 6).

Step 2: Connect the other end with the plastic air nozzle clockwise (Refer to Figure 7) and insert it into the car tire's inflation port, then fix it (Refer to Figure 8).

Step 3: Plug the cigarette lighter plug into the 12V DC socket (Refer to Figure 4). The display will light up.

Step 4: Press the Scene switch button [M] to select the car inflatable scene.

Step 5: Use the BAR unit button or PSI unit button to select your desired pressure unit.

Step 6: Use the pressurizing button [+] or decompressing button [-] to set the target pressure. The range is 1.8 to 2.75 BAR (1 PSI = 0.0689 BAR = 6.89 KPA).

Step 7: Press the On/Off button [▶️/⏹️] to start inflation.

During Inflation: You can adjust pressure using the [+] or [-] buttons, switch units with BAR/PSI buttons, and press the On/Off button [▶️/⏹️] to stop. The pump will automatically stop when the set pressure is reached.

Deflation Operation

SUP Deflation

Step 1: Plug the cigarette lighter plug into the 12V DC socket (Refer to Figure 4). The display will light up. Press the Scene switch button [M] to select the inflatable scene.

Step 2: Remove the hose from the inflation inlet. Connect the flexible conduit adaptor of the hose to the air pump's deflation outlet and twist clockwise to tighten it (Refer to Figure 9). The other end of the hose should remain connected to the airbag.

Step 3: Press the On/Off button [▶️/⏹️] to start deflation until all gas is discharged. The power can then be turned off to stop deflation.

Step 4: After deflation is complete, unplug the cigarette lighter plug from the 12V DC socket. Remove the hose from the air pump and airbag, and store it.

Precautions

• The applied power source must be a 12V DC source (Refer to Figure 4).
• Before inflating, confirm the required air pressure for the item to avoid injury from over-inflation.
• Do not block the inflation and deflation outlets; ensure they remain clear at all times.
• Observe local waste treatment regulations; do not discard the air pump randomly.
• Do not use the product if the hose is damaged; replace it immediately.
• Do not pull out the hose during inflation, as high pressure could cause injury.
• Do not operate the air pump for more than 20 minutes continuously. Allow it to cool for 30 minutes after each 20-minute operation to prevent motor overheating and damage.
• Disposal: Do not dispose of this product as unsorted municipal waste. It requires separate disposal for recycling electrical and electronic products. Proper recycling conserves natural resources and ensures environmentally friendly handling. [WEEE Symbol - Do Not Dispose with Household Waste]
• If any part of the air pump is damaged, do not use it; contact professional personnel for repair.
• For safety, do not point the inflation inlet towards yourself or others.
• Do not leave the product unattended while inflating.
• Start the car when using the product to prevent unnecessary damage to the vehicle's battery or electrical system.

Fault Handling

Maintenance and Storage

• After use, or before moving, maintaining, or adjusting the product, always pull out the DC plug from the socket.
• When idle, store the product properly after it has fully cooled.
• Do not expose the product to rain or immerse it in water.
• Store the product in a dry and ventilated place.

Suggestions

• The warranty period for this product is one year. It is recommended to use original accessories.
• Any fault not caused by the use of original accessories is outside the warranty scope.

Manufacturer and Contact Information

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

UK Representative: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

EU Representative: E-CrossStu GmbH Mainzer Landstr.69, 60329 Frankfurt am Main.

Important Warnings

To reduce the risk of injury, users must read the instructions manual carefully.

[FCC Certified] This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

[WEEE Symbol - Do Not Dispose with Household Waste] This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste but must be taken to a collection point for recycling electrical and electronic devices.

General Safety Warnings:

• This appliance can be used by children aged 8 years and above, and persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
• Keep the air pump out of reach of children.
• This product shall not be exposed to rain or immersed in water.
• Before moving, maintaining, repairing, or adjusting this product, first pull out the cigarette lighter plug from the socket.
• Do not bury the wire in the soil; place it in a safe zone where it will not be damaged by mowers or other equipment.
• If the power wire is damaged, it must be changed by the manufacturer, its service agent, or similarly authorized personnel to avoid risk.
• If you are standing in water or your hands are wet, do not plug or pull the cigarette lighter plug.
• Before inflating, check the maximum bearable pressure of the inflatable product, as the air bag may be damaged if this pressure is exceeded.
• Before use, check the cigarette lighter socket for rust or residue. Poor electrical conduction can cause overheating of the product or power source, damaging the product.
• The product cannot be used in flammable and explosive environments.
• Use this equipment at an ambient temperature not exceeding 40 degrees Celsius.
• The pressure line of the product is only suitable for the original wave pipe.
• Do not disassemble the device without authorization. This product does not contain user-serviceable spare parts.
• Do not cover or obstruct the product with paper or other objects, as this may affect heat dissipation and cooling.
• Ensure the wave pipe is not broken and that the switch and pressure screen are functioning correctly before use.
• Keep away from heat sources, humidity, dust, and direct sunlight.
• The purpose of using this product is limited to the description in this instruction book.