VEVOR HT-737PRO Paddle Board Pump

Product Introduction

The VEVOR HT-737PRO is an intelligent power storage air pump featuring a highlight LED display with preset pressure value. It is designed to inflate various items such as inflatable tents, inflatable beds, and canoes. The pump incorporates an intelligent pressure system that automatically stops inflation once the preset pressure value is reached.

This product also supports deflation, allowing you to empty inflatable products for easier folding and storage when not in use.

Product Parameters

List of Accessories

Please ensure all the following accessories are included in the box before use. If any items are missing, please contact your local agents or distributors.

Details of Accessories

Diagram of the VEVOR HT-737PRO air pump with numbered components:

• 1. Inflation inlet
• 2. Deflation outlet
• 3. Highlight the LED display
• 4. Decompressing button [➖]
• 5. Pressurizing button [➕]
• 6. On/off button [?]
• 7. Pressure unit toggle button [PSI/BAR]
• 8. LED Button [?]
• 9. Silicone Cover
• 10. Flexible conduit adaptor
• 11. Hose
• 12. Air nozzle
• 13. Handle
• 14. Type-C cable
• 15. USB charging output port
• 16. Type-C power input interface
• 17. LED Light

Illustration showing how to connect the hose to an air bag's inflation valve.

Safety Instructions

⚠️ Warning:

• This appliance can be used by children aged 8 years and above, and persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, provided they have been given supervision or instruction concerning safe use and understand the hazards involved.
• Keep children far away from this product.
• Do not expose this product to rain or immerse it in water.
• Before inflating, check the maximum bearable pressure of the inflatable product to prevent damage from exceeding it.
• The use of this product is limited to the descriptions in this instruction book.
• Do not use in flammable or explosive environments.
• Use this equipment at ambient temperatures not exceeding 40 degrees Celsius.
• The pressure line is suitable only for the original wave pipe.
• Ensure the wave pipe is not broken and that the switch and pressure screen are functioning correctly before use.
• Keep away from heat sources, humidity, dust, and direct sunlight.
• Do not throw this product into fire due to explosion or battery leakage risks.
• This product contains non-replaceable batteries.

[FCC Certified] This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

[WEEE Symbol] This product is subject to European Directive 2012/19/EC. The symbol of a crossed-out wheelie bin indicates separate refuse collection is required in the European Union for the product and its accessories. Products marked this way must not be discarded with normal domestic waste but taken to a collection point for recycling electrical and electronic devices.

Inflation Operation

1. Connect the end with the flexible conduit adaptor of the hose to the air pump inflation inlet and twist clockwise to tighten it (See Fig 1).
2. Install the other end of the hose into the air bag's air tap, twist clockwise to tighten, then insert the inflation valve of the air bag and twist clockwise to fix it (See Fig 2).
3. After completing these steps, press and hold the On/Off button [?] for 3 seconds for the display to light up. Short press the On/Off button [?] to start inflating. Press the On/Off button [?] again for 3 seconds to stop working.

Inflation Controls:

• Press the pressure unit toggle button [PSI/BAR] to select your desired unit.
• Press the pressurizing button [➕] or decompressing button [➖] to set the pressure value, ranging from 0 to 20 PSI (1 PSI = 0.0689 BAR = 6.89 KPA).
• During inflation, you can use the pressurizing [➕] or decompressing [➖] buttons to adjust the pressure value. Use the pressure unit toggle button [PSI/BAR] to switch units. Press the On/Off button [?] to stop.
• Press and hold the On/Off button [?] for 3 seconds to directly start the high-pressure pump.

Notices:

• Upon completion of inflation, the pump will automatically turn off within 2 minutes.
• The air pump will stop working automatically when the set pressure value is reached.
• When not in use, turn off the power switch, detach the hose from the air pump and air bag, and store it properly.
• The factory set pressure value is 20 PSI. On subsequent uses, the pump will default to the last set pressure value.

Deflation Operation

1. Remove the hose from the inflation inlet.
2. Connect the end with the flexible conduit adaptor of the hose to the air pump deflation outlet and twist clockwise to tighten it (See Fig 3). The other end should remain connected to the air bag.
3. In standby status, press the On/Off button [?] to start deflation. The pump will stop working after all gas is discharged when the On/Off button [?] is pressed for 3 seconds.

When not in use, please take down the hose from the air pump air bag and store it.

Precautions

• The pump uses Type-C USB (5V/2A or 9V/2A) for charging. The product should not be operated while charging.
• Do not block the inflation or deflation outlets; ensure they remain smooth at all times.
• Observe local waste treatment provisions; do not discard the air pump randomly.
• Do not use the product if the hose is damaged; replace it immediately.
• Do not pull out the hose during inflation, as the high pressure can cause injury.
• Do not operate the air pump for more than 20 minutes continuously. Motor overheating may cause internal damage. Allow the pump to cool for 30 minutes after 20 minutes of use.
• If any part of the air pump is damaged, do not use it and contact professional personnel for repair.
• To prevent risk, do not point the inflation inlet towards your face or body.
• Do not leave the product unattended while inflating.
• Disposal: Do not dispose of this product as unsorted municipal waste. It must be collected separately for special disposal.
• The built-in batteries must be removed from the equipment and disposed of properly before scrapping.
• Please fully charge the battery at least once every 6 months to maintain its normal usage.

Charging

Please use the provided Type-C USB cable for charging. During charging:

• Indicators will flash.
• In fast charging mode, the red indicator remains on.

Make sure the battery is fully discharged before the first charge. If the battery is discharged and the internal temperature is too high, it is recommended to cool it down before charging. Avoid leaving the electric air pump in a state of no electricity for extended periods.

USB Port Output Operation

In standby or power-on state, connect one end of the USB cable to the USB/Charger Port on the pump and the other end to a USB port on your phone or other digital products (See Fig 5).

Outdoor Lighting

In standby status, press the LED lighting button [?]:

• First press: Turns the light on.
• Second press: LED light starts flashing.
• Third press: Turns the light off.

Fault Handling

Maintenance and Storage

• After use, or before moving, servicing, or adjusting the product, please remove the power plug from the electric outlet.
• Cool the product down and store it in its box when not in use.
• Use the product indoors and protect it against direct sun exposure or rain.
• Store it in a dry and ventilated place.

Suggestions

The warranty period for this product is one year. It is recommended to use original parts; otherwise, any failure thereof will not be covered by the warranty.

Manufacturer Information:

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Importer Information:

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

Representative Information:

UK REP: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

EC REP: E-CrossStu GmbH Mainzer Landstr.69, 60329 Frankfurt am Main.