Anderic RR1003 Universal Remote Control Manual

Installing Batteries

To install batteries, insert a coin into the slot at the bottom of the remote and turn it ¼ counterclockwise to remove the door. Insert two AAA batteries (sold separately) ensuring correct polarity as indicated on the remote's back. Replace the battery cover by aligning it and rotating it ¼ clockwise until tight.

Programming Code Method

1. Press and hold the [TV POWER] and [OK] keys simultaneously for approximately 3 seconds. The indicator light will turn on; then release the keys.
2. Input the four-digit code. If the code is accepted, the indicator light will turn off. If not accepted, the indicator light will flash four times and exit programming.
3. Check the code with your TV to ensure all necessary keys function. If not, repeat the above steps with a different code.

Programming Fast Search

1. Press and hold the [TV POWER] and the [CH+] keys simultaneously for approximately 3 seconds. The indicator light will turn on; then release the keys.

   Note: The following step offers two ways to scan the code database. Holding the CH+ or CH- keys will scan quickly and automatically forward or backward. Pressing and releasing the CH+ or CH- key will advance or reverse one code at a time. The CH+ key scans forward, and the CH- key scans backward.

2. Press and release (for one-by-one progression) or press and hold (for automatic scanning) the CH+ (forward) or CH- (backward) key until your TV responds by adjusting the volume. Release the key. Test other keys to confirm proper TV response.
3. To save, press the [OK] key. The indicator light will turn off to confirm. Test the remote with the TV. If the TV does not respond as expected, repeat these steps.

Setting Sleep Timer

Note: If your TV responds appropriately when the [SLEEP] key is pressed after programming, this setup is unnecessary.

1. Press and hold the [SLEEP] key for approximately three seconds. The indicator light will turn on to a solid state; then release the key.
2. Using the keypad, enter a two-digit number from 01 to 99 to set the sleep timer in minutes. For example, entering [30] will set the remote to power off the TV in 30 minutes.
3. Position the remote in a direct line of sight with the TV and wait. The remote will power off the TV when the time has elapsed.

   Note: Pressing the [TV POWER] or the [SLEEP] key will cancel the sleep function.

Code Identification

Note: Use these instructions to identify the current code programmed in the remote.

1. Press and hold the [TV POWER] and the [OK] keys simultaneously for approximately 3 seconds. The indicator light will turn on; then release the keys.
2. Input code [990]. The indicator light will flash twice and then turn off.
3. Press the [1] key; the indicator light will flash. Count the number of flashes to determine the code's first digit. If the indicator light does not flash, the digit is 0.
4. Repeat step 3 for keys [2], [3], and [4] to identify the second, third, and fourth digits, respectively.
5. Press any other key to exit code identification mode. The remote will also exit this mode if no key is pressed for 10 seconds.

Learning Function

Note: This programming option allows the RR1003 remote to learn any key from an original infrared (IR) remote. Maintain a distance of 3-5 CM between remotes.

1. Press and hold the [TV POWER] and the [VOL+] keys simultaneously for approximately 3 seconds. The indicator light will turn on; then release the keys.
2. While pointing the head of the original remote towards the head of the RR1003, press and release a key on the original remote. The indicator light on the RR1003 will flash. Then, press and release the same key on the RR1003 remote. The indicator light will return to a steady on state.
3. Repeat step 2 for all keys you wish to learn.
4. When finished, press and hold the [TV POWER] and the [VOL-] keys simultaneously to save and exit. The indicator light will turn off.

   Note: If there is no activity for 25 seconds, the RR1003 will exit Learning Mode.

Reset to Factory Default

1. Press and hold the [TV POWER] and the [OK] keys simultaneously for approximately 3 seconds. The indicator light will turn on; then release the keys.
2. Input code [977].
3. Press [OK]. The indicator light will flash four times and then turn off, indicating the remote has reset.

TV Code List

This manual includes a comprehensive list of TV codes for various brands, including LCD, Plasma, and Panel TVs. Due to the extensive nature of the list, it is not fully reproduced here. For the complete and most up-to-date TV code list, please refer to the original product manual or visit the official Anderic website.