Trane Product Data

Product Specifications

The following tables detail the specifications for the Trane Split System Cooling units.

Notes:
(a) Certified in accordance with the Unitary Air-conditioner equipment certification program which is based on AHRI standard 210/240.
(b) Calculated in accordance with N.E.C. Only use HACR circuit breakers or fuses.
(c) Standard line lengths - 60', Standard lift - 60' Suction and Liquid line. For Greater lengths and lifts refer to refrigerant piping software Pub#32-3312-0* (* denotes latest revision).
(d) * = 15, 20, 25, 30, 40 and 50 foot lineset available.

Sound Power Level

Sound power levels for the Trane split system cooling units, rated in accordance with AHRI Standard 270-2008.

Note: Rated in accordance with AHRI Standard 270-2008. *For Reference Only.

Accessory Description and Usage

• Anti-Short Cycle Timer: Solid state timing device that prevents compressor recycling until five (5) minutes have elapsed after satisfying call or power interruptions. Use in areas with questionable power delivery, commercial applications, or long linesets.
• Evaporator Defrost Control: SPST Temperature actuated switch that cycles the condenser off as the indoor coil reaches freeze-up conditions. Used for low ambient cooling down to 30°F with TXV.
• Rubber Isolators: Five (5) large rubber donuts to isolate the condensing unit from transmitting energy into the mounting frame or pad. Use where sound transmission needs to be minimized.
• Hard Start Kit: Start capacitor and relay to assist compressor motor startup. Use in areas with marginal power supply, on long linesets, or low ambient conditions.
• Extreme Condition Mount Kit: Bracket kits to securely mount the condensing unit to a frame or pad without removing any panels. Use in areas with high winds or on commercial rooftops.

AHRI Standard Capacity Rating Conditions

AHRI Standard 210/240 Rating Conditions

1. Cooling: 80°F DB, 67°F WB air entering indoor coil; 95°F DB air entering outdoor coil.
2. High Temperature Heating: 47°F DB, 43°F WB air entering outdoor coil; 70°F DB air entering indoor coil.
3. Low Temperature Heating: 17°F DB air entering indoor coil.
4. Rated indoor airflow for heating is the same as for cooling.

AHRI Standard 270 Rating Conditions

(Noise rating numbers are determined with the unit in cooling operations.) Standard Noise Rating number is at 95°F outdoor air.

Model Nomenclature

The model number provides specific information about the unit. For example, the model number 4TWV0036A1000AA breaks down as follows:

• 4: Refrigerant Type (4 = R-410A)
• TW: Product Type (T = Split Cooling)
• V: Product Family (V = Variable Speed)
• 0036: Nominal Capacity in 000s of BTUs (36,000 BTU/hr)
• A: Major Design Modifications
• 1: Power Supply (1 = 200-230/1/60 or 208-230/1/60)
• 000: Minor Design Modifications
• AA: Unit Parts Identifier

Other elements in the nomenclature indicate:

• Split System Connections: 1-6 Tons (e.g., 3 for 3 tons)
• Family SEER: e.g., 6 = 16 SEER
• Product Type: W = Split Heat Pump, T = Split Cooling
• Product Family: V = Variable Speed, Z = Leadership -Two Stage, X = Leadership, R = Replacement/Retail
• Family SEER: 6 = 16, 3 = 13, 4 = 14, 8 = 18, 5 = 15, 9 = 19, 0 = 20
• Split System Connections 1-6 Tons: 0 = Brazed
• Nominal Capacity in 000s of BTUs
• Major Design Modifications
• Power Supply: 1 = 200-230/1/60 or 208-230/1/60, 3 = 200-230/3/60, 4 = 460/3/60
• Secondary Function
• Minor Design Modifications
• Unit Parts Identifier

Schematic Diagrams

The document includes electrical schematic diagrams for different model series:

• Figure 1: 018 - 048 Models: This diagram illustrates the electrical connections for models 018 through 048. It shows power supply inputs, compressor (CPR), fan motor (OD FAN MTR), various control components like High Pressure Cutout (HPCO), Low Pressure Cutout (LPCO), Outdoor Thermostat (ODT), and System On-Off Switch (SM). It also details wiring colors and includes notes regarding optional accessories and installation requirements.
• Figure 2: 049 & 061 Models: This schematic covers models 049 and 061, depicting similar electrical components and connections as Figure 1, adapted for these specific models. It includes a legend for components and wire color coding.
• Figure 2: 060 Models: This diagram is for the 060 models, showing the electrical layout. It features components such as the compressor (CPR), fan motor (OD FAN MTR), various safety switches (HPCO, LPCO), and control terminals. Notes provide guidance on optional components and installation.

Outline Drawing

The outline drawing provides physical dimensions and connection points for the outdoor units. The table below details these dimensions (labeled A through K) for each model.

Diagram Description: The drawing shows a typical outdoor unit with a top-mounted fan. It indicates clearances for the service panel, electrical, and refrigerant components. It also highlights the location of the electrical service panel, low voltage K.O., and gas/liquid line service valve connections.

Mechanical Specification Options

General

The Outdoor Units are fully charged from the factory for up to 15 feet of piping. This unit is designed to operate at outdoor ambient temperatures as high as 115°F. Cooling capacities are matched with a wide selection of air handlers and furnace coils that are AHRI certified. The unit is certified to UL 1995. Exterior is designed for outdoor application.

Casing

Unit casing is constructed of heavy gauge, galvanized steel and painted with a weather-resistant powder paint finish on all louvered panels and the fan top panel. The corner panels are prepainted. All panels are subjected to our 1,000 hour salt spray test. The base is made of a CMBP-G30 weatherproof material to resist corrosion.

Refrigerant Controls

Refrigeration system controls include condenser fan, compressor contactor, and high pressure switch. High and low pressure controls are inherent to the compressor. A factory supplied liquid line drier is standard. Some models may require field installation.

Compressor

The compressor features internal over temperature, pressure protection, and a total dipped hermetic motor. Other features include: Centrifugal oil pump and low vibration and noise.

Condenser Coil

The outdoor coil provides low airflow resistance and efficient heat transfer. The coil is protected on all four sides by louvered panels.

Low Ambient Cooling

As manufactured, this system has a cooling capacity to 55°F. The addition of an evaporator defrost control permits operation to 40°F. The addition of an evaporator defrost control with TXV permits low ambient cooling to 30°F.

Thermostats

Cooling only and heat/cooling (manual and automatic change over). Sub-base to match thermostat and locking thermostat cover.

Evaporator Defrost Control

See Low Ambient Cooling.