LUMME Convection Heater

Product Overview

This document provides instructions for the Lumme LU-CH606A Convection Heater. The heater is designed for heating rooms and features multiple heat settings and thermostat control.

Visual Description: The heater is a white convection unit with black accents. It features a top grille for air outlet, a side control panel with switches and a thermostat knob, a handle for portability, and two stabilizing feet at the base. The text "НЕ НАКРЫВАТЬ" (Do Not Cover) is displayed on the top grille.

The manual is available in multiple languages, including Russian (RUS), English (GBR), Ukrainian (UKR), Kazakh (KAZ), and Belarusian (BLR).

Safety Precautions

Please read all instructions carefully before use and keep this manual for future reference.

• This appliance is intended for heating rooms only. Do not use it for any other purpose.
• Before initial use, check that the product's technical specifications match your local power supply.
• The appliance must be connected to an earthed socket.
• If the heater has been exposed to temperatures below 0°C, allow it to reach room temperature for at least 2 hours before switching it on.
• Use only for domestic purposes as described in this manual. It is not intended for industrial use.
• Do not use the appliance in rooms with high humidity, outdoors, or near water sources like baths, showers, sinks, or pools. Water ingress can cause serious damage. Keep the appliance away from water.
• Do not touch the appliance or power cord with wet hands when plugging in or unplugging. Do not place the appliance on wet surfaces.
• Do not immerse the appliance, cord, or plug in water or other liquids. If this happens, immediately unplug from the power outlet and contact a service center. Do not touch the appliance while it is in water if it is still connected to power.
• Ensure the appliance is used in a well-ventilated area with at least 1 meter of clear space around it for proper air circulation and heat dissipation.
• Place the appliance on a flat, stable, and heat-resistant surface capable of supporting its weight.
• Do not attempt to disassemble, modify, or repair the appliance yourself.
• Before each use, check the appliance, plug, and power cord for any damage or malfunctions. If any issues are found, unplug the unit and contact a qualified service center.
• If the plug does not fit the socket or is difficult to insert, seek assistance from a qualified professional.
• Do not extend the power cord or use extension cords or adapters.
• Fully unwind the power cord before each use. Ensure the cord does not touch sharp edges or hot surfaces.
• Do not pull, twist, or wrap the power cord around the appliance. Do not move the heater by pulling the cord.
• The appliance is not designed to operate with external timers or remote control systems.
• Always unplug the heater from the power outlet before moving it.
• Keep the appliance away from flammable, explosive substances, aerosols, and combustible materials. Keep it away from open flames.
• To prevent fire hazards, do not place the heater near curtains or furniture. Avoid contact with melting or flammable materials, fabrics, or drapes. Do not place the heater on carpets or soft surfaces like sofas or beds.
• Do not place the appliance directly under a power outlet.
• Do not insert any objects into the heat outlet or air grilles.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they are supervised or instructed by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance. Keep the appliance out of reach of children.
• Do not allow children to use the appliance. Exercise extra caution when operating it near children or pets.
• To prevent overloading the electrical network, do not connect the heater and other high-power appliances to the same electrical line simultaneously.
• Do not leave the appliance unattended while it is plugged in.
• Always unplug the appliance from the power outlet before cleaning and when it is not in use.
• Do not pull the power cord when unplugging; grasp the plug firmly.
• Do not place heavy objects on the heater or touch it with sharp objects, as this may cause deformation or rust. Mechanical damage to the casing or components, and normal wear of the paint coating are not covered by warranty.
• Using non-recommended accessories may be dangerous or damage the appliance.
• Before storing the appliance, wait until it cools down to room temperature.
• The surface of the heater gets very hot during operation. Exercise extreme caution, especially when children are nearby.
• CAUTION: Ensure the appliance is always operated in a vertical position. Operation in any other position is prohibited.
• Never touch the hot surfaces of the heater during operation; use the handles, knobs, and switches.
• The heated area must be at least 5 m².
• WARNING: DO NOT COVER THE HEATER TO PREVENT OVERHEATING. FIRE HAZARD: DO NOT COVER THE APPLIANCE WITH ANYTHING! DO NOT USE THE HEATER TO DRY OR HEAT CLOTHING AND OTHER ITEMS!
• Failure to follow safety measures may result in fire, electric shock, or burns. Damage caused by improper use voids the warranty.

Assembly

Floor Mounting

If the appliance will be used on the floor, attach the feet to the base of the heater using the 4 provided screws. Ensure they are correctly positioned in the designated holes on the base.

Visual Aid Description: An illustration shows the heater base and the feet being attached with screws. The text "УБЕДИТЕСЬ В ТОМ, ЧТО ПРИБОР ЗАНЯЛ УСТОЙЧИВОЕ ВЕРТИКАЛЬНОЕ ПОЛОЖЕНИЕ!" (Ensure the appliance is in a stable vertical position!) is displayed.

Wall Mounting

Note: The distance between the bottom of the heater and the floor must be at least 15 cm. The feet must be removed for wall mounting.

Steps for Wall Mounting:

1. Measure the distance between the two upper bracket holes on the back panel of the heater. Determine the desired height for mounting.
2. Drill two holes in the wall, approximately 4 cm deep, ensuring the distance between them matches the heater's bracket holes. Insert wall plugs (dowels) into the holes.
3. Attach the two upper wall brackets to the wall using screws, as shown in the diagram.
4. Before mounting the heater, attach the two lower brackets to the bottom of the heater, with the shorter side facing down.
5. Hang the heater onto the upper wall brackets, aligning the heater's back panel holes with the brackets.
6. Secure the heater by engaging it with the bracket slots.
7. With the heater correctly mounted, mark the positions for the lower wall brackets on the wall using a pencil.
8. Remove the heater from the wall.
9. Drill two holes at the marked positions and insert wall plugs.
10. Re-hang the heater as described in step 5. Attach the lower brackets to the wall using screws, but do not overtighten them initially.

Visual Aid Description: Diagrams illustrate the process: Diagram A shows bracket hole placement on the heater. Diagram B shows wall brackets (X2). Diagram C shows lower brackets being attached to the heater. Diagrams D (a, b, c, d) show bracket details and wall attachment points.

Using the Appliance

Before First Use

• Unpack the appliance and remove all packaging materials and labels. Keep warning labels and the serial number plate.
• Clean the appliance with a damp cloth. Clean accessories in soapy water, rinse, and dry thoroughly.

Note: It is normal for the heater to emit a slight smell or fumes when first turned on or after a long period of disuse. This will disappear shortly.

Operation

• Choose a suitable location, considering the safety instructions.
• Before connecting to power, set the thermostat knob to the leftmost position (minimum).
• Plug the heater into a suitable socket.
• Turn the thermostat knob fully clockwise to the maximum setting.
• Switch on the heating elements using the heating mode switches (1). An indicator light will illuminate. Using both switches activates maximum power (up to 2000 Watts).
• When the desired room temperature is reached, slowly turn the thermostat knob counter-clockwise until you hear a click. The heater will now maintain the set temperature by cycling on and off automatically.

Temperature Regulation

Temperature can be regulated in two ways:

1. By rotating the thermostat knob: clockwise to increase temperature, counter-clockwise to decrease.
2. By setting different power modes using the switches: 850W (Minimum Power), 1150W (Average Power), 2000W (Maximum Power - both switches on).

Turning Off

• To turn off the heater, turn the thermostat controller to the leftmost position and the heating mode switches to the off position.
• Only then, disconnect the unit from the power supply.
• Always allow the appliance to cool down completely before storing it.
• Ensure nothing obstructs the air vent system to prevent damage to the unit.

Cleaning and Maintenance

• Always unplug the heater from the wall socket and allow it to cool down before cleaning.
• Wipe the exterior surface with a soft, damp cloth and then buff with a dry cloth.
• Do not use detergents, abrasives, organic solvents, or aggressive liquids.
• Do not allow water to enter the heater.
• If the heater is not used for extended periods, protect it from dust and store it in a clean, dry place.

Technical Specifications

Manufacturer and Service Information

Manufacturer: Cosmos Far View International Limited, Room 701, 16 apt, Lane 165, Rainbow North Street, Ningbo, China. Made in China.

Warranty: Does not cover consumables like filters, ceramic and non-stick coating, rubber seals, etc. Production date is indicated by the 4th and 5th characters (month) and 6th and 7th characters (year) of the serial number.

The manufacturer reserves the right to change specifications without notice. Please check at the time of purchase.

For current information about service centers, visit: http://lumme-ru.com