Cambridge Casual Assembly Instructions

Teak Dining Chair

Model: IT-121697T

Customer Service Information:

Email: info@cambridge-casual.com

Toll-free number: 1-888-287-4275 (Monday to Friday, 9:00 am to 5:00 pm CST)

For faster response, please provide item number, code for missing parts, purchase receipt, and pictures of damaged parts.

General Information & Tips

• Read assembly instructions before assembling.
• Assemble on a non-abrasive surface like carpet to avoid damage.
• Ensure all bolts are tightly fastened before use.
• This chair is not for commercial use.
• Verify all parts are present before beginning assembly.
• Wait until all steps are completed before tightening bolts.

Tools Required

• 8" Philips screwdriver (for tightening bolts and screws)
• Rubber Mallet (for tapping wooden caps)

Parts and Hardware List

Assembly Steps

Step 1

Attach the back support (B), front apron (D1), and back apron (D2) into the side frames (A1 & A2). Secure using 1 1/2" bolts (E). Do not tighten bolts yet.

Step 2

Attach the seat (C) to the assembly, starting with the front side.

Step 3

Secure the seat (C) using 1" screws (F).

Step 4

Ensure all parts are correctly connected and tighten all bolts and screws using a screwdriver. Tap in the wooden caps (G) to cover the bolt heads using a rubber mallet. Tap carefully to avoid damaging the wood frame.

The chair is now ready for use.

Teak Dining Table

Model: IT-321165T

Customer Service Information:

Email: info@cambridge-casual.com

Toll-free number: 1-888-287-4275 (Monday to Friday, 9:00 am to 5:00 pm CST)

For faster response, please provide item number, code for missing parts, purchase receipt, and pictures of damaged parts.

General Information & Tips

• Read assembly instructions before assembling.
• Assemble on a non-abrasive surface like carpet to avoid damage.
• Ensure all nuts are tightly fastened before use.
• This table is not for commercial use.
• Verify all parts are present before beginning assembly.
• Wait until all steps are completed before tightening nuts.

Tools Required

• Wrench (Provided) (for tightening all nuts)

Parts and Hardware List

Assembly Steps

Step 1

Attach the leg frames (B) into each corner of the table top (A). Assemble the washers (C), spring washers (D), and nuts (E) to the leg frames (B). Tighten the nuts using the wrench.

Step 2

Turn the table upright. Ensure all parts are fully connected and tighten all nuts completely using the wrench.

Congratulations! The table is now ready for use.

Care Maintenance

Cambridge Casual furniture is crafted using sustainably harvested wood. While designed to withstand the elements, proper care and maintenance will ensure longevity and appearance.

General Outdoor Care

• Regular cleaning is important.
• Use furniture covers or store indoors during inclement weather (heavy rain, winter).
• Ensure furniture and cushions are clean and dry before covering or storing.
• Remove wet cushions from frames and air dry to prevent mold and mildew.
• Avoid storing furniture near heating or cooling vents.
• Do not let liquids stand on surfaces.
• Do not place hot items directly on furniture surfaces.
• Use a padded barrier when writing on furniture.
• Avoid leaving furniture in puddles or on wet ground.

Unfinished Natural / Finely Sanded Teak

• Unique graining and color variations are natural characteristics of teak.
• Small splits, knots, and joint lines contribute to the character without affecting quality.
• Natural teak weathers to a silver-gray patina; a teak sealer or oil can maintain the honey brown color.
• Teak expands and contracts with climate changes, potentially causing hairline cracks, which do not compromise structural integrity.
• Surface mildew may form but does not impact durability and can be removed with cleaning.

Cleaning Teak:

• Use warm water and mild dish soap. Scrub gently with the grain. Rinse thoroughly and air dry.
• For tougher stains, use a mixture of 1 cup chlorine bleach, 1 cup laundry detergent, and 1 gallon of water. Apply with a soft-bristle brush, let sit for 5-10 minutes, rinse thoroughly.
• Start with milder solutions; use stronger cleaners or teak cleaners if needed.
• For remaining stains, lightly sand with 120-grit sandpaper.

Weathered Teak

This finish is hand-applied and may fade or wear over time with outdoor exposure. The underlying natural teak will become exposed and turn gray. To preserve the finish, store in covered storage or use a furniture cover during extreme weather or winter.

Spa Collection Teak

Maintain with solvent-based polyurethane protective coating every six months, or as recommended by the manufacturer. For everyday maintenance, clean with mild detergent and a clean cloth. Avoid chemical solvents.

Painted Hardwood

Clean with water-based mild detergent and a clean cloth every six months. Avoid chemical solvents. Color may fade with continuous exposure to sunlight and rain. Store indoors or use a furniture cover during extreme weather.

Cushions

• Fabrics are breathable and water-resistant, not waterproof.
• Remove and store cushions in a dry place when not in use or during inclement weather.
• Air dry wet cushions thoroughly, ensuring zippers are open and cushions are on their sides for drainage.
• Clean periodically to remove dust and dirt. Wipe spills immediately.
• Spot clean stains promptly.
• Removable cushion covers can be machine washed in cold water with mild soap and air dried.
• Rotate cushion inserts periodically to distribute wear and prevent loss of shape.

Synthetic Rattan, Woven Polyrope, & Textilene

• Dust periodically with a soft, dry cloth.
• Use a non-metallic, soft bristle brush for loose dirt.
• For spot cleaning, rinse with a hose and dry with a soft cloth.
• For thorough cleaning, use a mixture of mild soap and water with a soft-bristle brush. Do not use abrasive cleaners. Rinse and dry thoroughly.

Proper care will ensure your furniture lasts for many years.

1 Year Limited Warranty

This is a limited warranty for the original purchaser. Regular care and maintenance are required.

• 1 Year Limited Frame Warranty: Wood frames are warranted against structural defects. Natural aging, fading, and wear on components like chair feet are not covered.
• Finish Warranty: Warranted against peeling, cracking, or blistering for 1 year, provided the unit has not been scratched or abraded. Scratches and dents from normal wear and tear are not covered.
• Fabric Warranty: Fabrics and cushions are warranted against workmanship or material defects. Discoloration or damage due to chemicals, cleaning products, sun lotions, oil spills, improper maintenance, or extreme heat is not covered.

Warranty Exclusions:

• Commercial or non-residential use.
• Clearance items, display models, or items purchased "as is".
• Damage from unreasonable use, abuse, freight, acts of nature, vandalism, fire, lack of care, or improper assembly.
• Exposure to severe weather (snowstorm, hail, heavy rainfall, flooding, hurricane, extreme heat).
• Accidental damage, customer repairs, or modifications.
• Straps and fabric fading/discoloration from improper exposure or accidental contact with elements, oils, fluids, or chemicals.
• Hardware corrosion or rusting.
• Buckling or splitting of tubing from exposure to water and freezing temperatures.
• Normal wear and tear, loss of use, inconvenience, money, travel, packaging, or consequential/incidental damages.

The manufacturer's responsibility does not exceed the product's value. The warranty starts from the date of purchase.

For Quality Control and Verification:

Claims require the following documents:

• Packing slip / Invoice
• Photos or video of damaged/defected/missing part
• Item number and part code (from assembly instructions)

Claims will not be processed without proper documentation. Retain all damaged goods until the claim is concluded.

Warranty terms are subject to change without notice.