STOREMOLLA Chest of 8 Drawers

Step 1

Attach drawer slide components (part 10101822) to the side panels (part 100349). Use 6 screws (part 100349) for each side panel. Ensure correct orientation for 'L' (left) and 'R' (right) sides.

Step 2

Attach drawer slide components (part 10101822) to the other side panels. Use 4 screws (part 100349) for each panel. Ensure correct orientation for 'L' and 'R' sides.

Step 3

Connect two side panels together using dowels and cam locks. The diagram shows two panels being joined, with arrows indicating the insertion of dowels and cam locks.

Step 4

Attach a base panel (part 153552) to the assembled side panels using 2 cam locks (part 153552).

Step 5

Attach drawer slide components (part 10101822) to the inner frame. Use 6 screws (part 100349) for each side.

Step 6

Fold a panel (part 153552) into position. This panel appears to be a divider or support.

Step 7

Attach drawer slide components (part 10101822) to the other side of the frame. Use 6 screws (part 100349) for each side.

Step 8

Insert dowels (part 101345) into the pre-drilled holes of the drawer slide assemblies. Use 14 dowels in total.

Step 9

Attach cam lock posts (part 10047135) to a large panel, likely the back or base. Use 12 cam lock posts. The diagram shows a hand inserting the posts and a 'no' symbol indicating incorrect insertion.

Step 10

Attach rotating cam lock fittings (part 10071733) to two drawer front panels. Use 4 fittings. The diagram shows the fitting being inserted and then rotated to lock.

Step 11

Insert two vertical drawer divider panels into the main frame. Use 2 rotating cam lock fittings (part 10071733) to secure them.

Step 12

Insert another vertical drawer divider panel into the main frame. Use 3 rotating cam lock fittings (part 10071733) to secure it.

Step 13

Insert a side panel into the frame. Use 3 rotating cam lock fittings (part 10071733) to secure it. The warning symbol ⚠️ indicates not to force the panel.

Step 14

Prepare four long horizontal panels. Insert 6 dowels (part 101345) into each panel.

Step 15

Attach rotating cam lock fittings (part 10071733) to the ends of the horizontal panels prepared in Step 14. Use 6 fittings per panel.

Step 16

Insert cam lock posts (part 10047135) into the ends of the horizontal panels. Use 6 posts per panel. The diagram shows correct and incorrect insertion of the post.

Step 17

Attach the assembled horizontal panels to the main frame. Use 6 cam lock posts (part 10047135) per panel. Also, attach drawer slides (2x) to the side panels.

Step 18

Attach the top panel to the main frame. Use 3 screws (part 104257) and the Allen key (part 100001) to secure it.

Step 19

Insert cam lock posts (3x) into the side panels. The diagram shows the correct insertion angle and direction.

Step 20

Attach the main frame to the base. Use 3 screws (part 100001) with Allen key, securing the frame to the base structure.

Step 21

Attach the top panel. Use 1 screw (part 104257) with Allen key (part 100001) to secure it to the side panel.

Step 22

Attach the top panel to the main frame. Use 6 screws (part 104257) with Allen key (part 100001) to secure it.

Step 23

Attach the back panels. Use 18 cam lock posts (part 151706) and 18 cam locks (part 151705) to secure the back panels to the frame. The arrow indicates the direction of insertion.

Step 24

Attach the bottom panel. Use 5 screws (part 107862) to secure the bottom panel. The diagram shows two people carefully turning the unit over.

Step 25

Adjust the leveling feet. The diagram shows the feet being adjusted up and down. The warning symbol ⚠️ indicates to check stability.

Step 26

Attach the anti-tip hardware to the back of the unit. Use 2 fittings (part 370172) and screws. The diagram shows the fitting being attached and then screwed into the wall.

Step 27

Mark the wall for the anti-tip device. The 'X' marks indicate drilling points on the wall.

Step 28

Wall Mounting Instructions: The supplied screws and plugs can be used with most solid (A) and hollow (B) walls. For solid wood (C), use screws without plugs. If uncertain, seek professional advice.

• Type A (Solid Wall): Drill Ø 8 mm hole, insert plug, screw in. Depth approx. 70 mm.
• Type B (Hollow Wall): Drill Ø 8 mm hole, insert plug, screw in. Depth approx. 30 mm.
• Type C (Solid Wood): Drill Ø 3 mm hole, screw in directly. Depth approx. 30 mm.

Step 29

Attach wall mounting brackets (part 10102070) to the unit. Use 2 brackets. The diagram shows the bracket being attached to the back of the unit.

Step 30

Secure the unit to the wall using the wall mounting brackets. Insert screws (part 109572) through the brackets and into the wall anchors.

Step 31

Prepare drawer base panels. Insert 4 dowels (part 101345) into each panel.

Step 32

Attach cam lock posts (part 10047135) to the drawer base panels. Use 4 posts per panel. The diagram shows correct and incorrect insertion.

Step 33

Assemble drawer sides. Insert the drawer base panel into the grooves of the drawer sides. The warning symbol ⚠️ indicates correct orientation.

Step 34

Attach drawer front panels. Use 4 rotating cam lock fittings (part 10071733) to secure the drawer front to the drawer sides.

Step 35

Insert the back panel into the drawer. The arrow indicates the direction of insertion.

Step 36

Attach drawer handles (part 10040242) to the drawer fronts. The diagram shows a hammer being used to tap the handle into place.

Step 37

Insert the assembled drawer into the main unit. The diagram shows the drawer sliding into place, with close-ups of the drawer slides engaging.

Step 38

Insert the assembled drawer into the main unit. The diagram shows the drawer sliding into place, with close-ups of the drawer slides engaging.

Step 39

Attach cam lock posts (part 10095420) to the drawer sides. Use 4 posts per drawer.

Step 40

Attach rotating cam lock fittings (part 119030) to the drawer fronts. Use 4 fittings. The diagram shows the fitting being inserted and rotated.

Step 41

Attach drawer handles (part 10112730) to the drawer fronts using screws (part 10091382). Use 1 screw per handle.

Step 42

Insert the assembled drawers into the main unit. The diagram shows the drawers being slid into place.

Step 43

Insert drawers into the unit. The diagram shows a drawer being inserted and a close-up of the locking mechanism engaging with a 'Click!' sound indicated.

Step 44

Insert drawers into the unit. The diagram shows a drawer being slid into place.

Step 45

Insert the assembled drawers into the main unit. The diagram shows drawers being slid into place.

Step 46

Attach drawer fronts to the drawer boxes. Use 2 fittings (part 10040242) per drawer. The diagram shows the front being attached and a close-up of the locking mechanism engaging with a 'Click!' sound indicated.

Step 47

Insert the assembled drawers into the main unit. The diagram shows drawers being slid into place.