Assembly Instructions 43000579 Kitchen Bench Prep Trolley
Care Instructions
WIPE CLEAN WITH SOFT DAMP CLOTH. DO NOT USE SCOURERS, ABRASIVES OR CHEMICAL SOLVENTS. CHECK AND TIGHTEN ALL PARTS REGULARLY. STORE IN A DRY PLACE AND KEEP AWAY FROM DIRECT WATER AND SUNLIGHT. FOR INDOOR AND DOMESTIC USE ONLY.
Warnings
DO NOT STAND, SIT OR LEAN ON THE TROLLEY. USE ONLY ON A FLAT SURFACE. WHEN USING THE TOP AS A CHOPPING SURFACE, LOCK ALL WHEELS AND PLACE THE TROLLEY AGAINST A WALL OR OTHER FIXED UNIT TO AVOID UNINTENDED MOVING. DO NOT USE UNTIL ALL SCREWS, BOLTS AND KNOBS ARE FIRMLY SECURED. THIS PRODUCT CONTAINS SMALL PARTS AND SHARP POINTS; KEEP AWAY FROM CHILDREN AND BABIES. ADULT ASSEMBLY REQUIRED. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY.
Maximum Safe Load
- Top Panel: 10KG
- Drawer: 2KG
- Wine Shelf: 3KG
- Wire Basket: 3KG
- Bottom Shelf: 3KG
Assembly Notes
Important: Do not tighten the screws fully during assembly. Fully tighten screws after the final assembly steps.
Hardware List
| Part | Description | Quantity |
|---|---|---|
| A | Screw, 6*30mm | 6PCS |
| B | Screw, 15*9mm | 6PCS |
| C | Screw, 6*30mm | 10PCS |
| D | Screw, 4*35mm | 4PCS |
| E | Handle | 1PC |
| F | Screw, 4*16mm | 1PC |
| G | Screw, 6*40mm | 8PCS |
| H | Support Bracket/Part | 8PCS |
| I | Allen Key | 1PC |
| J | Drawer Stopper | 2PCS |
| K | Metal Pin | 2PCS |
| L | Screw, 6*27mm | 4PCS |
| M | Nut | 4PCS |
| N | Wrench | 1PC |
| O | Wheel without stopper | 2PCS |
| P | Wheel with stopper | 2PCS |
Assembly Steps
Step 1
Attach part H onto boards 4 & 7 into the corresponding position. Put part C on to frame 3 into the corresponding position. Attach frame boards 4 & 7 onto frame 3 with screw G.
Diagram Description: Shows frame parts 3, 4, and 7 being assembled. Part H is inserted into designated slots on boards 4 and 7. Part C is attached to frame 3. Frame boards 4 and 7 are then connected to frame 3 using screw G [?], tightened with Allen key I [?].
Step 2
Attach board 6 on to board 7 from step 1.
Diagram Description: Shows board 6 being attached to board 7, completing a section of the frame.
Step 3
Put part H onto board 4 & 7 into the corresponding position. Put part C on to frame 2 into the corresponding position. Attach frame 2 into board 4 & 7 & 6 from step 2 with screw G.
Diagram Description: Shows frame part 2 being attached to the assembled structure (boards 4, 7, and 6) using screw G [?], tightened with Allen key I [?].
Step 4
Attach part O & P onto the legs with screw M & L. Tighten with Allen key I. Kindly reminder: Part O is the wheel without stopper. Part P is the wheel with stopper. Note: use part N [?] onto the nut M [⚙️] to align the part L, tighten with Allen key I [?].
Diagram Description: Shows wheels being attached to the bottom legs. Part O (wheel without stopper ☸️) and Part P (wheel with stopper ☸️) are attached using screw M [?] and nut L [?]. A wrench N [?] is shown for tightening the nut M [⚙️]. Tighten with Allen key I [?].
Step 5
Attach panel A onto board 1.
Diagram Description: Shows top panel (board 1) being attached to a frame structure using screws A [?].
Step 6
Attach board 1 from step 5 onto frame 2&3 from step 4 with screw B & C. Ensure all parts align.
Diagram Description: Shows the assembled frame structure (from step 4) being connected to the top panel assembly (board 1, from step 5) using screws B [?] and C [?].
Step 7
Part I: Attach board 8 & 10 onto board 9 with part D.
Part II: Put board 11 onto board 8 & 10.
Part III: Attach panel A to board 11. Attach panel E to board 11 using screw F. Attach board 12 to board 8 & 10 with part B & C.
Diagram Description: This step details the assembly of the drawer.
Part I: Shows drawer base parts 8, 9, and 10 being assembled using screws D [?].
Part II: Shows drawer side panel (board 11) being attached to the assembled drawer base.
Part III: Shows panel A being attached to board 11. Panel E is attached to board 11 using screw F [?]. Board 12 is attached to boards 8 & 10 using screws B [?] and C [?].
Step 8
Put drawer from step 7 onto trolley from step 5, when drawer put into 1/3, then fix J into the corresponding position as per diagram.
Diagram Description: Shows the assembled drawer being inserted into the trolley. Drawer stopper J [?] is then fixed into its corresponding position.
Step 9
Put part 5 onto trolley from step 8, then fix K into the corresponding position as per diagram.
Diagram Description: Shows wire basket (part 5) being placed into the trolley. Metal pin K [?] is then fixed into its corresponding position.
Step 10
Finish the assembly.
Diagram Description: Shows the fully assembled Kitchen Bench Prep Trolley.
