WARNING:
To reduce the risk of fire, electric shock, or personal injury, please strictly follow these instructions:
- The device must be mounted in a vertical position with the receptacle facing downward and at least 2FT above the ground level.
- Do not connect any devices which exceed the maximum ratings of the timer.
- Do not immerse in water.
- Children are not allowed to use the timer without supervision.
- Do not disassemble or repair the product; only authorized service personnel should perform such tasks.
- Always unplug and store indoors when not in use.
Product Layout
The Jewenwils Outdoor Light Sensor Timer features a compact design with key components for automated lighting control:
- 1. Timer Dial: Allows selection of 2 to 8 hours of operation or a dusk-to-dawn setting with a daily repeat function.
- 2. Sensor: This photocell sensor automatically turns the timer ON at dusk and OFF at dawn.
- 3. Power Indicator Light: Illuminates to show whether the timer is currently ON or OFF.
Visual Description: The device is a cylindrical timer with a power cord extending from both ends. The main body features a circular dial at the top, a sensor window below it, and a power indicator light. The dial has markings for different time settings and a dusk-to-dawn option. The device is designed for outdoor use, with a robust casing and a ground stake for vertical mounting.
Operating Instructions
The timer offers several operating modes:
- OFF: Power is OFF to attached devices.
- ON: Power is ON to attached devices continuously.
- Dusk - Dawn: Power will turn on at dusk and remain on until dawn.
- 2 Hrs: Power will turn on at dusk and remain on for 2 hours.
- 4 Hrs: Power will turn on at dusk and remain on for 4 hours.
- 6 Hrs: Power will turn on at dusk and remain on for 6 hours.
- 8 Hrs: Power will turn on at dusk and remain on for 8 hours.
The selected cycle repeats every 24 hours.
Notes
- The timer operates on a daily repeat cycle after initial setting. In the event of a power failure, the timer will stop operating. Once power is restored, the desired operating mode must be reset according to the operating instructions.
- Once programming activates at dusk in the 2H, 4H, 6H, or 8H Mode, the program cycle will repeat until the timer is reset. External lighting sources such as headlights, porch lights, or street lamps will not interfere with the active timer program.
- In the Dusk-Dawn Mode, temporary light sources like headlights, porch lights, and other external light sources will not interfere with the photocell function unless the external light source is on for more than 15 minutes. In such a case, the timer will shut off until darkness is restored.
- When set to "ON", the timer will provide continual power to attached devices until the timer is switched to "OFF" or any other operating mode.
Specifications
| Category | Detail |
|---|---|
| Input Voltage | 125V, 60Hz |
| Max Power Rating | 125V, 60Hz, 1875W |
| Resistance | 15A |
| General Use | 15A |
| Tungsten | 1000W |
| Electronic Ballast | 500VA |
| Ballast (120Vac, 60Hz) | 8.3A |
| Horsepower (HP) | 1/2HP |
| Cord | 2FT SJTW 14/3 AWG |
Safety Information
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
One Year Limited Warranty
Jewenwils provides a One Year Warranty for materials and workmanship from the purchase date, supported by its professional R&D and QC teams. The warranty does not cover damage caused by personal misuse or improper installation.
Customers should attach their Order ID and Name for assistance from the dedicated customer service team.
Made in China
