Jewenwils Outdoor Light Sensor Timer

Product Layout

The Jewenwils Outdoor Light Sensor Timer features a compact design with a main control dial and multiple outlets. The device includes a power cord with a standard plug for connection to a power source and three outlets for connecting controlled devices. A light sensor is integrated for automatic operation based on ambient light levels.

• 1. Timer dial: Allows selection of operating modes including 2 to 8 hours, dusk to dawn, and daily repeat function.
• 2. Power: A power indicator light shows if the timer is turned on or off.
• 3. Sensor: The sensor activates the timer at dusk and deactivates it at dawn.
• 4. 3 Outlets: These outlets are where lights or other devices controlled by the timer are plugged in.

Operating Instructions

• OFF: Power is OFF to attached devices.
• ON: Power is ON to attached devices.
• Dusk - Dawn: Power will turn on at dusk and remain on until dawn.
• 2 Hrs: Power will turn on at dusk and remain on for 2 hours.
• 4 Hrs: Power will turn on at dusk and remain on for 4 hours.
• 6 Hrs: Power will turn on at dusk and remain on for 6 hours.
• 8 Hrs: Power will turn on at dusk and remain on for 8 hours.
• Cycle repeats every 24 hours.

Notes

1. The timer repeats daily after setting. In case of power failure, it will stop operating. Once power is restored, reset the desired operating mode as per the operating instructions.
2. Once programming activates at dusk in the 2H, 4H, 6H, or 8H Mode, the program cycle will repeat until the timer is reset. External lighting sources like headlights, porch lights, and street lamps will not interfere with the active timer program.
3. In the Dusk-Dawn Mode, temporary light sources such as headlights, porch lights, and other external light sources will not interfere with the photocell function unless the external light source is on for more than 15 minutes. In such a case, the timer will shut off until darkness is restored.
4. When set to “ON”, the timer will provide continual power to attached devices until the timer is switched to "OFF", or to any of the other operating modes.

Specifications

Input Voltage:

• 125V, 60Hz.

Max Power Rating:

• 125V, 60Hz, 1875W, 15A Resistance, 15A General Use, 1000W Tungsten, 500VA Electronic Ballast, 120Vac, 60Hz, 8.3A Ballast, 1/2HP.

Cord:

• SJTW 14/3 AWG.

Safety Information

Federal Communications Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

One Year Limited Warranty

The product is supported by a professional R&D team and QC team, providing a One Year Warranty for materials and workmanship from the purchase date. The warranty does not cover damage caused by personal misuse or improper installation.

For customer service, it is recommended to attach the Order ID and Name for assistance.

The product is UL Listed (Underwriters Laboratories) and bears the recycling symbol (three chasing arrows), indicating compliance with safety standards and encouragement for recycling. It is manufactured in China.