Harbor Breeze LED Path Light

Introduction

Thank you for purchasing this Harbor Breeze product. These instructions are designed to help you enjoy your product with minimal assembly time. For additional information, visit Lowes.com, search the item number, and refer to the Guides & Documents tab.

For questions or issues, contact customer service at 1-888-251-1003 (8 a.m. - 8 p.m. EST, Monday - Sunday) or email partsplus@lowes.com. You can also visit www.lowespartsplus.com.

Preparation and Assembly

Estimated Assembly Time: 10 minutes

Tools Required: None

Before starting, ensure all parts are present by comparing them with the package contents list. Do not assemble if parts are missing or damaged.

Preparation/Préparation/Preparación

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list. If any part is missing or damaged, do not attempt to assemble the product.

Feeling Confident? Start Your Next Project

Visit www.lowes.com for more information.

Printed in China

Installation Overview

The installation involves connecting the low-voltage transformer to the fixture using a wire connector.

1. Connect Transformer: Insert the wire from the low-voltage transformer (sold separately) into the wire guide by twisting the wire into each end of the wire guide.
2. Align Pins: Align the pins on the connector top cover so that each pin lines up with opposite sides of the wire.
3. Secure Connector: Tighten the connector top cover securely, ensuring the pins completely pierce the plastic shield of the wire.

Diagram Description: The installation overview shows 5 steps. Step 1 shows the fixture (A) and the wire connector (B). Step 2 shows the wire connector (B) being attached to the low-voltage wire (C). Step 3 shows the wire connector (B) attached to the fixture wire (A) and the low-voltage wire (C). Step 4 shows the wire connector (B) with pins aligned to pierce the low-voltage wire (C). Step 5 shows the assembled fixture (A) with the connected low-voltage wire (C).

Troubleshooting

Care and Maintenance

Clean the lens, lamp head, and lamp stand regularly with a non-abrasive cleaner. Warning: Always ensure the flood light is unplugged and completely cool before cleaning.

Warranty

This fixture is warranted against defects in materials and workmanship for five (5) years from the original purchase date. For warranty service, call 1-888-251-1003 to obtain a Return Authorization number and further instructions. The manufacturer is liable for replacement of the defective item only.

Safety Information

Please read and understand this entire manual before assembly, operation, or installation.

Caution:

• This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
• The user is encouraged to try to correct interference by: reorienting or relocating the receiving antenna; increasing the separation between the equipment and receiver; connecting the equipment to an outlet on a different circuit than the receiver; or consulting a dealer or experienced radio/TV technician.
• Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
• This product is not a toy and must not be operated by children.
• Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
• Do not submerge in water. The product can be damaged.
• Use with 18AWG minimum, underground low-voltage circuit cord.
• The wire is intended for shallow burial, less than 6 in. deep.
• Install all luminaires 10 ft. or more from a pool, spa, or foundation.
• Keep lamp away from material that may burn.
• Do not touch hot lens, guard, or hot fixture housing.
• Do not operate or install a fixture with missing or damaged parts.
• Do not touch the LED at any time as this may cause damage to the fixture.