Harbor Breeze LED Path Light

Introduction

Thank you for purchasing this Harbor Breeze product. These instructions are designed to help you assemble and enjoy your new path light. For additional information, visit Lowes.com, search the item number, and refer to the Guides & Documents tab on the product page.

For questions or issues, contact customer service at 1-888-251-1003 (Monday-Sunday, 8 a.m. - 8 p.m. EST), via email at partsplus@lowes.com, or visit www.lowespartsplus.com.

Preparation

Before assembly, ensure all parts are present by comparing them with the package contents list. Do not attempt to assemble if any part is missing or damaged.

Estimated Assembly Time: 10 minutes.

No tools are required for assembly.

For more information, visit www.lowes.com.

Troubleshooting

Problem: The light does not turn on at night.

Possible Causes:

• The transformer is not plugged in or turned on.
• The fixture connector is not properly installed on the low-voltage cable.

Corrective Actions:

• Ensure the transformer is plugged in and turned on.
• Verify that the contact pins on the connector pierce the wire insulation and make proper contact with the wire.

Care and Maintenance

Regularly clean the lens, lamp head, and lamp stand using a non-abrasive cleaner. Always ensure the light is unplugged and completely cool before cleaning.

Warranty

This fixture is warranted against defects in materials and workmanship for five (5) years from the original purchase date. For warranty service, call 1-888-251-1003 to obtain a Return Authorization number and further instructions. The manufacturer is liable for replacement of defective items but not for other losses, damages, or injuries caused by the product.

Safety Information

Please read and understand this entire manual before assembling, operating, or installing the product.

Caution:

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received, including that which may cause undesired operation.

This equipment has been tested and found to comply with Class B digital device limits per FCC Rules. These limits provide reasonable protection against harmful interference in residential installations. The equipment generates, uses, and can radiate radio frequency energy. If not installed and used per instructions, it may cause harmful interference to radio or television reception. To correct interference, try one or more of the following:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from the receiver's circuit.
• Consult the dealer or an experienced radio/TV technician for assistance.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Warnings:

• This product is not a toy and must not be operated by children.
• Do not connect this fixture to an electrical system without equipment grounding.
• Do not submerge in water, as the product can be damaged.
• Use with an 18AWG minimum underground low-voltage circuit cord.
• The wire is intended for shallow burial, less than 6 inches deep.
• Risk of Electric Shock: Install all luminaires at least 10 feet (3.04 m) from pools, spas, or foundations.
• Keep the lamp away from flammable materials.
• Do not touch the hot lens, guard, or fixture housing.
• Do not operate or install a fixture with missing or damaged parts.
• Do not touch the LED at any time, as this may cause damage to the fixture.
• Ensure electricity to the wires is shut off (remove fuse or turn off circuit breaker) before working on them.
• For use with low-voltage landscape lighting systems only.

Installation Overview

The following steps outline the installation process:

1. Step 1: Attach the light fixture to the stake. Connect the low-voltage wire to the fixture's wire lead.

   [Diagram Description: The light fixture is shown being screwed onto a stake. An arrow indicates connecting the low-voltage wire from the fixture to the main low-voltage cable.]

2. Step 2: Route the low-voltage wire through the stake. Prepare to connect the wire connector.

   [Diagram Description: The low-voltage wire is shown being threaded through the hollow stake. An arrow points to the wire connector that will be used to join the fixture wire to the main cable.]

3. Step 3: Connect the wire connector (A) to the low-voltage wire. Ensure the connector's pins pierce the wire insulation for a secure connection.

   [Diagram Description: A close-up shows the wire connector (labeled 'A') being placed over the stripped end of the low-voltage wire. The diagram illustrates the pins of the connector penetrating the wire's insulation.]

4. Step 4: The fixture is now assembled and ready for installation into the ground.

   [Diagram Description: The complete path light assembly, with the wire connector attached, is shown. It is positioned as if being pushed into the ground.]

Wire Connection Instructions: Insert the wire from the low-voltage transformer (sold separately) into the wire guide by twisting the wire into each end. Align the pins on the connector top cover so each pin lines up with opposite sides of the wire. Securely tighten the connector top cover, ensuring the pins completely pierce the plastic shield of the wire.

Package Contents

• Path Light Fixture (A) x 1
• Wire Connector (B) x 1