Power Dynamics PDY212SM & PDY215SM Active Stage Monitor

Important Safety Precautions

Please read this manual thoroughly before using the unit to ensure full benefit from all features and to avoid fire and/or electrical shock. Repairs must only be carried out by qualified technicians. Keep this manual for future reference.

• Consult a specialist before initial use. A slight smell may occur upon first use, which is normal and will disappear.
• The unit contains voltage-carrying parts; do NOT open the housing.
• Do not place metal objects or liquids into the unit, as this may cause electrical shock and malfunction.
• Do not place the unit near heat sources (radiators) or on vibrating surfaces. Do not cover ventilation holes.
• The unit is not suitable for continuous use.
• Handle the mains lead with care; a faulty or damaged lead can cause electrical shock or malfunction.
• When unplugging from a mains outlet, always pull the plug, never the lead.
• Do not plug or unplug with wet hands.
• If the plug or mains lead is damaged, it must be replaced by a qualified technician.
• If the unit is damaged such that internal parts are visible, do NOT plug it in or switch it on. Contact your dealer.
• To prevent fire and shock hazard, do not expose the unit to rain or moisture.
• All repairs should be carried out by a qualified technician only.
• Connect to an earthed mains outlet (220-240Vac/50Hz) protected by a 10-16A fuse.
• During thunderstorms or if the unit will not be used for an extended period, unplug it from the mains. Rule: Unplug when not in use.
• If the unit has been stored for a long time, condensation may occur. Allow the unit to reach room temperature before switching it on.
• Never use the unit in humid rooms or outdoors.
• Follow applicable guidelines and instructions to prevent accidents in companies.
• Do not repeatedly switch the unit on and off, as this shortens its lifespan.
• Keep the unit out of reach of children and do not leave it unattended.
• Do not use cleaning sprays on switches; residues can cause dust and grease buildup. Seek professional advice for malfunctions.
• Do not force controls.
• Keep the unit at least 60cm away from computers or TVs, as the speaker can cause a magnetic field.
• If the product has a built-in lead-acid battery, recharge it every 3 months if not in use to prevent permanent damage. Replace damaged batteries with identical specifications and dispose of them responsibly.
• If the unit has been dropped, have it checked by a qualified technician before switching it on again.
• Do not use chemicals to clean the unit; use only a dry cloth.
• Keep away from electronic equipment that may cause interference.
• Use only original spare parts for repairs to avoid serious damage or dangerous radiation.
• Switch the unit off before unplugging it from the mains or other equipment. Unplug all leads and cables before moving the unit.
• Ensure the mains lead cannot be damaged by foot traffic. Check the mains lead for damage before each use.
• Verify that your power outlet matches the mains voltage (220-240Vac/50Hz). Check voltage compatibility if traveling.
• Keep original packing material for safe transport.

Warning Symbols:

• ⚡ This mark indicates high voltages inside the housing that can cause a shock hazard.
• ❗ This mark draws attention to important instructions in the manual that must be read and followed.

The unit is CE certified. Unauthorized modifications will invalidate the CE certificate and guarantee.

Note: For normal operation, use the unit in rooms with temperatures between 5°C/41°F and 35°C/95°F.

Unpacking Instructions

CAUTION! Carefully unpack the box upon receipt. Check contents for completeness and condition. Notify the shipper immediately of any shipping damage and retain packaging materials. If the product must be returned, it must be in its original factory box and packaging.

If the device has been exposed to drastic temperature fluctuations (e.g., after transportation), do not switch it on immediately. Condensation may damage the device. Leave the device switched off until it reaches room temperature.

Connections

The rear panel features the following connections:

1. CHANNEL 1 VOLUME LEVEL:

Rotate to adjust the volume level of channel 1.

2. MIC/LINE SWITCH:

Press to switch between line and microphone input.

3. CHANNEL 1 INPUT:

Combo jack input, suitable for both XLR and 6.3mm jack.

4. CHANNEL 2 VOLUME LEVEL:

Rotate to adjust the volume level of channel 2.

5. RCA INPUT:

RCA line signal input sockets.

6. CHANNEL 2 INPUT:

Combo jack input, suitable for both XLR and 6.3mm jack.

7. LOW CUT / FLAT SWITCH:

Switch to filter out low frequencies (low cut) or keep the full frequency range (flat).

8. MASTER VOLUME LEVEL:

Rotate to adjust the master volume level.

9. MIX OUTPUT:

XLR output socket for mix output signal.

10. FUSE HOLDER:

Screw-type fuse holder.

11. POWER SWITCH:

Switch to turn the device ON or OFF.

12. POWER CONNECTOR:

Socket for plugging in the supplied power cord.

Replacing the Fuse

If the fuse is defective, replace it with a fuse of the same type and value. Before replacing the fuse, unplug the mains lead.

Procedure:

1. Open the fuse holder on the rear panel with a suitable screwdriver.
2. Remove the old fuse from the fuse holder.
3. Install the new fuse in the fuse holder.
4. Replace the fuse holder in the housing.

Technical Specifications

The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice.

Compliance Information

The products referred to in this manual conform to the European Community Directives to which they are subject:

European Union:
Tronios B.V., Bedrijvenpark Twente Noord 18, 7602KR Almelo, The Netherlands
2014/35/EU, 2014/30/EU, 2011/65/EC

United Kingdom:
Tronios Ltd., 130 Harley Street, London W1G 7JU, United Kingdom
S.I. 2016:1101, S.I. 2016:1091, S.I. 2012:3032

Specifications and design are subject to change without prior notice.

Visit www.tronios.com for more information.

Copyright © 2023 by Tronios, The Netherlands