ASSEMBLY INSTRUCTIONS
Item #: N759P223021
Thank you for purchasing this quality Product. Be sure to check all packing material carefully for small parts, which may have come loose inside carton during shipment. Identify and count all parts and compare with the parts list below.
ASSEMBLY INSTRUCTION:
- Remove hardware from box and sort by size.
- Please check to see that all hardware and parts are present prior to start of assembly.
- Please follow attached instructions in the same sequence as numbered to ensure fast and easy assembly.
WARNING!
- Do not attempt to repair or modify parts that are broken or defective. Please contact the store immediately.
- This product is for home use only and not intended for commercial establishments.
- Two persons are required for assembly.
- Approximate assembly time: 1/2 hours.
- Component parts and fittings are contained in the box. Please sort out all parts before you begin to assemble the item. This is to make sure you always use the correct part.
- It is STRONGLY RECOMMENDED that you ANCHOR this product. Tipping furniture can cause serious injuries and death. To prevent your furniture from tipping forward, it is strongly recommended that you securely attach this product to a wall or other solid surface, using the anchor straps and provided appropriate fixings.
Parts List
| No. | Component | Qty | No. | Component | Qty |
|---|---|---|---|---|---|
| A | Sink | 1 | N2 | Bottom Flip down Box - Left | 1 |
| B | Side Panel-Left | 1 | O | Sides Flip down Box | 4 |
| C | Side Panel-Right | 1 | P | Front Drawer Panel - Top | 1 |
| D | Back Panel - Up | 1 | P1 | Sides Drawer Panel - Top | 2 |
| E | Back Panel - Low | 1 | P2 | Back Drawer Panel - Top | 1 |
| F | Door | 1 | Q | Front Drawer Panel - Bottom | 1 |
| G | Middle Panel | 1 | Q1 | Sides Drawer Panel - Bottom | 2 |
| H | Bottom | 1 | Q2 | Back Drawer Panel - Bottom | 1 |
| I | Racket Panel | 2 | R | Bottom Drawer Panel | 2 |
| K | Mid Racket Panel | 2 | S | Front Rail - Above | 1 |
| L | Round horizontal Bar | 2 | T | Front Rail #1 - Middle | 1 |
| M | Front Flip down Box - Right | 1 | U | Front Rail #2 - Middle | 2 |
| M1 | Back Flip down Box - Right | 1 | V | Front Rail - Below | 1 |
| M2 | Bottom Flip down Box - Right | 1 | W | Shelf | 1 |
| N | Front Flip down Box - Left | 1 | |||
| N1 | Back Flip down Box - Left | 1 |
Hardware List
| No. | Hardware | Qty | No. | Hardware | Qty |
|---|---|---|---|---|---|
| 1 | Cam Lock | 20 | 12 | Rod Support hinges - Right | 1 |
| 2 | Cam Lock Screws | 20 | 13 | Swivel Hinges | 4 |
| 3 | Wooden | 35 | 14 | Shelf Support | 4 |
| 4 | Hinges | 2 | 15 | Screws M3.5x12 | 20 |
| 5 | Screws M3.5x15 | 12 | 16 | Screws M4x20 | 32 |
| 6 | Handle | 5 | 17 | Screws M4x30 | 9 |
| 7 | Knob | 1 | 18 | Allen Bolts 1/4" x 40 | 4 |
| 8 | Screws M4x30 | 8 | 19 | Flat Washers 1/4" x 16 x 2 | 4 |
| 9 | Screws M4x25 | 1 | 20 | Lock washers 1/4" x 11 x 2 | 4 |
| 10 | Screws M4x17 | 2 | 21 | Allen key | 1 |
| 11 | Rod Support hinges - Left | 1 | Not Included |
Step 1
Assemble the base structure. Insert cam lock screws (2) into the designated holes on the side panels (B, C) and the bottom panel (H). Align the panels and secure them by inserting cam locks (1) into the corresponding holes and turning them to lock. Then, attach the back panel - low (E) and back panel - up (D) to the assembled base using cam lock screws (2) and cam locks (1). The diagram illustrates the connection of panels B, C, H, D, and E using hardware 1 and 2.
Parts Used:
- B (Side Panel-Left)
- C (Side Panel-Right)
- D (Back Panel - Up)
- E (Back Panel - Low)
- H (Bottom)
Hardware Used:
- 1 (Cam Lock) x 20
- 2 (Cam Lock Screws) x 20
Step 2
Attach the middle panel (G) and racket panels (I) to the base assembly. Insert cam lock screws (2) into the middle panel and racket panels. Connect to the side panels (B, C) and secure with cam locks (1). The diagram shows the assembly of panels G, I, B, C using hardware 1 and 2, along with wooden dowels (3).
Parts Used:
- B (Side Panel-Left)
- C (Side Panel-Right)
- G (Middle Panel)
- I (Racket Panel) x 2
Hardware Used:
- 1 (Cam Lock) x 4
- 2 (Cam Lock Screws) x 3
- 3 (Wooden) x 3
Step 3
Attach the drawer runners (T, U) to the side panels (B, C) and middle panel (G). Insert cam lock screws (2) into the panels and secure with cam locks (1). Attach the front rail - above (S) and front rail #1 - middle (T) to the side panels. Use allen bolts (18), flat washers (19), and lock washers (20) to secure. The diagram shows the assembly of drawer runners and front rails to the side and middle panels.
Parts Used:
- B (Side Panel-Left)
- C (Side Panel-Right)
- G (Middle Panel)
- S (Front Rail - Above)
- T (Front Rail #1 - Middle)
Hardware Used:
- 1 (Cam Lock) x 5
- 3 (Wooden) x 13
- 18 (Allen Bolts 1/4" x 40) x 2
- 19 (Flat Washers 1/4" x 16 x 2) x 2
- 20 (Lock washers 1/4" x 11 x 2) x 2
- 21 (Allen key) x 1
Step 4
Attach the front rail #2 - middle (U) and front rail - below (V) to the side panels (B, C). Use cam locks (1) and wooden dowels (3) to secure. The diagram shows the attachment of front rails U and V to the side panels.
Parts Used:
- B (Side Panel-Left)
- C (Side Panel-Right)
- U (Front Rail #2 - Middle) x 2
- V (Front Rail - Below)
Hardware Used:
- 1 (Cam Lock) x 5
- 3 (Wooden) x 9
- 18 (Allen Bolts 1/4" x 40) x 2
- 19 (Flat Washers 1/4" x 16 x 2) x 2
- 20 (Lock washers 1/4" x 11 x 2) x 2
- 21 (Allen key) x 1
Step 5
Attach the bottom panel (H) to the assembled frame. Use screws (17) to secure the bottom panel to the side panels (B, C) and back panels (D, E). The diagram shows the bottom panel being attached to the main cabinet frame.
Parts Used:
- B (Side Panel-Left)
- C (Side Panel-Right)
- D (Back Panel - Up)
- E (Back Panel - Low)
- H (Bottom)
Hardware Used:
- 17 (Screws M4x30) x 5
Step 6
Install the shelf supports (14) into the pre-drilled holes on the side panels (B, C). Place the shelf (W) onto the shelf supports. The diagram shows shelf supports being inserted into side panels and the shelf being placed.
Parts Used:
- B (Side Panel-Left)
- C (Side Panel-Right)
- W (Shelf)
Hardware Used:
- 14 (Shelf Support) x 4
- 15 (Screws M3.5 x 12) x 4
Step 7
Assemble the drawer boxes. Attach front drawer panels (P, Q) to side drawer panels (P1, Q1) and back drawer panels (P2, Q2) using cam locks (1), wooden dowels (3), and hinges (4). Attach handles (6) to the front drawer panels using screws (9). The diagram shows the assembly of drawer sides, front, and back panels, and the attachment of handles. Page 7 continues Step 7 with assembly of drawer boxes M and N, and attachment of rod support hinges (11, 12) and screws (15).
Parts Used:
- P (Front Drawer Panel - Top)
- P1 (Sides Drawer Panel - Top) x 2
- P2 (Back Drawer Panel - Top)
- Q (Front Drawer Panel - Bottom)
- Q1 (Sides Drawer Panel - Bottom) x 2
- Q2 (Back Drawer Panel - Bottom)
- F (Door)
- M (Front Flip down Box - Right)
- M1 (Back Flip down Box - Right)
- M2 (Bottom Flip down Box - Right)
- N (Front Flip down Box - Left)
- N1 (Back Flip down Box - Left)
Hardware Used:
- 1 (Cam lock) x 6
- 3 (Wooden) x 10
- 4 (Hinges) x 2
- 5 (Screws M3.5 x 15) x 4
- 6 (Handle) x 3
- 7 (Knob) x 1
- 9 (Screws M4 x 25) x 1
- 11 (Rod Support hinges) x 1
- 12 (Rod Support hinges) x 1
- 15 (Screws M3.5 x 12) x 4
Step 8
Attach the assembled drawer boxes to the cabinet frame. Use screws (16) to secure the drawer boxes to the side panels (B, C) and middle panel (G). Attach handles (6) to the drawer fronts using screws (8, 10). The diagram shows drawer boxes being attached and handles being screwed on.
Parts Used:
- B (Side Panel-Left)
- C (Side Panel-Right)
- G (Middle Panel)
- P (Front Drawer Panel - Top)
- Q (Front Drawer Panel - Bottom)
- R (Bottom Drawer Panel) x 2
Hardware Used:
- 16 (Screws M4 x 20) x 16
- 6 (Handle) x 3
- 8 (Screws M4 x 30) x 4
- 10 (Screws M4 x 17) x 2
Step 9
Attach the sink (A) to the top surface of the cabinet. Install swivel hinges (13) to the door (F) and the cabinet frame using screws (5, 15). Attach the door to the cabinet. The diagram shows the top assembly with sink and door attachment.
Parts Used:
- A (Sink)
- F (Door)
Hardware Used:
- 5 (Screws M3.5 x 15) x 8
- 13 (Swivel Hinges) x 4
- 15 (Screws M3.5 x 12) x 12
Step 10
Place the assembled top unit onto the cabinet base. Apply silicone sealant (not included) to the edges as indicated. The diagram shows the completed vanity unit with the top in place and a note about silicone.
Materials Mentioned:
- Silicone (not included)
