Ingenuity SimpleComfort™ Compact Soothing Swing - Chambray

Important Safety Information

WARNING:

• Fall and Strangulation Hazards: Infants have suffered head injuries falling from seats and have strangled in straps.
• Always use the restraint system and adjust to fit snugly.
• Stop using the product when the infant attempts to climb out (approximately 9 months).
• Do not use this product if your child can sit up unaided or weighs more than 9 kg (20 lbs). Do not use if your child weighs less than 3 kg (6 lbs).
• Always stay near and watch the baby during use. This product is not safe for sleep or unsupervised use. If the baby falls asleep, remove the baby as soon as possible and place on a firm, flat sleep surface like a crib or bassinet. Never let the child sleep in this product.
• Do not move or lift this product with the baby inside. Never lift the product using the toy bar as a handle.
• Always place the product on the floor. Never use on an elevated surface (e.g., a table).
• Never attach any additional strings or straps to the product or toy bar.
• Suffocation Hazard: Young infants have limited head and neck control. If the seat is too upright, the infant's head can drop forward and compress the airway.
• Always keep the swing seat fully reclined until the infant is at least 4 months old AND can hold their head up without help.
• Suffocation Hazard: Babies have suffocated when seats tipped over on soft surfaces.
• Never use on a bed, sofa, cushion, or other soft surface.

Prevent Serious Injury or Death:

• Never leave the child unattended.
• To avoid injury, ensure children are kept away when unfolding and folding the product.
• Do not let children play with this product.
• When using the USB cord, only use the one supplied with this swing.
• Check the USB cord and wall adapter regularly for damage. Do not use if any damage has occurred.
• Use USB cord only with a 5 Volt/1 Amp (5 Watts) USB A wall adapter.
• The product shall only be used with a transformer for toys. The transformer is not a toy.
• This product is only to be connected to equipment bearing either of the following symbols: ? (IEC symbol for Class II equipment) or ? (IEC symbol for SELV/DC output).
• Do not use extension cords.

CAUTION: This product contains small parts. Adult assembly required.

Product Information

• The provided USB cord is 183cm (72 inches) in length.
• Please read all instructions before assembly and use.
• Care should be taken in unpacking and assembly.
• Examine the product frequently for damaged, missing, or loose parts.
• Do not use if any parts are missing, damaged, or broken. Contact Kids2 for replacement parts and instructions if needed. Never substitute parts.
• This product does not replace a cot or crib. If the child falls asleep, they should be placed in a suitable cot or crib.

Care and Cleaning

• Seat pad and headrest: Remove from frame. Fasten buckles on seat restraint and seat pad. Fasten all hook-and-loop patches to the corresponding patch. Machine wash with cold water, gentle cycle. No bleach. Tumble dry, low heat.
• Toy bar and toys: Wipe clean with a damp cloth and mild soap. Air dry. Do not immerse in water.
• Frame: Wipe the metal frame with a soft, clean cloth and mild soap.
• Storage: When putting the swing away for storage, always store in a dry location, away from any heat sources, and out of the sun.

Parts List

Assembly Instructions

Refer to the diagrams for assembly steps. Ensure all parts are correctly aligned and secured.

Step 1: Attach the left leg assembly (1) and right leg assembly (2) to the control module assembly (4).

Step 2: Connect the bottom frame assembly (3) to the leg assemblies.

Step 3: Attach the swing arm assembly (5) to the frame.

Step 4: Secure the swing arm assembly using screws (A) and nuts (B).

Step 5: Attach the left recline mechanism (6) and right recline mechanism (7) to the swing arm.

Step 6: Connect the foot rest tube (8) and back rest tube (9) to the seat pad (10).

Step 7: Attach the seat pad assembly to the swing arm.

Step 8: Secure the seat pad using the provided fasteners.

Step 9: Attach the toy bar with toys (11) to the swing arm.

Step 10: Attach the headrest (12) to the seat pad.

Step 11: Connect the USB A cable (13) to the control module.

Using the Swing Control Module

Power Switch: Touch to power the module on/off.

Speed Selector Button and Indicator: Provides 6 speed settings and OFF. Touch to cycle through speeds. LEDs indicate the selected speed.

Swing Timer Select Button and Indicator: Set timer for 15, 20, or 30 minutes. LEDs indicate the selected time. Default is 15 minutes.

Nature Sounds/Music Button: Play music and nature sounds. Touch to select desired sound/song. Auto-shutoff after approximately 20 minutes.

Volume Control: Adjust volume for music and nature sounds.

Using the Seat Restraint

Follow the diagrams to properly secure the infant in the seat restraint. Ensure all buckles are fastened and straps are adjusted snugly.

Using the Recline Function

Adjust the seat recline angle as shown in the diagrams.

Rotation of the Seat

The seat can be rotated as illustrated in the diagrams.

FCC Statement / CAN ICES-3 (B) / NMB-3(B)

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Déclaration FCC / CAN ICES-3 (B) / NMB-3(B)

Cet appareil est conforme à l'article 15 de la réglementation FCC. Son utilisation est sujette aux deux conditions suivantes : 1) ce dispositif ne peut causer d'interférences nuisibles, et 2) ce dispositif doit accepter toute interférence reçue, y compris les interférences pouvant causer un fonctionnement indésirable.

ATTENTION : Toute modification apportée à cet appareil, sans consentement explicite des responsables conformité, est susceptible d'annuler le droit d'usage de cet appareil.

REMARQUE : Cet article a été testé et déclaré conforme aux exigences requises pour les appareils numériques de classe B, conformément à l'article 15 de la réglementation FCC. Ces exigences visent à assurer une protection raisonnable contre les interférences nuisibles dans une installation chez des particuliers. Cet appareil génère, utilise et peut émettre de l'énergie radioélectrique, et s'il n'est pas installé et utilisé conformément aux instructions, il est susceptible de perturber les communications radio.

Nous ne pouvons garantir la non-interférence pour une installation donnée. Lorsque vous constatez que le matériel perturbe effectivement la réception radio ou télévision, vous pouvez vérifier ces interférences en éteignant et rallumant l'appareil. Dans ce cas, essayez une ou plusieurs des mesures suivantes :

• Réorientez ou déplacez l'antenne de réception.
• Éloignez l'appareil et le récepteur.
• Raccordez le matériel à une prise hors-circuit connexion de ce récepteur.
• Adressez-vous au fournisseur ou à un technicien expert en radio et télévision.