Ingenuity SimpleComfort™ Compact Soothing Swing - Parker™

IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

WARNING

FALL and STRANGULATION HAZARDS

Infants have suffered head injuries falling from seats and have strangled in straps.

• ALWAYS use the restraint system. Adjust to fit snugly.
• STOP using product when infant attempts to climb out (approximately 9 months).
• DO NOT use this product once your child can sit up unaided or weighs more than 9 kg/20 lbs. DO NOT use this product if your child weighs less than 3kg/6 lbs.
• Stay near and watch baby during use. This product is not safe for sleep or unsupervised use. If baby falls asleep, remove baby as soon as possible and place baby on a firm, flat sleep surface such as a crib or bassinet. Never let the child sleep in this product.
• DO NOT move or lift this product with the baby inside it. Never lift product using a toy bar as a handle.
• ALWAYS place product on floor. NEVER use this product on an elevated surface (e.g. a table).
• NEVER attach any additional strings or straps to product or toy bar.

SUFFOCATION HAZARD

Young infants have limited head and neck control. If the seat is too upright, infant's head can drop forward and compress the airway.

• ALWAYS keep swing seat fully reclined until infant is at least 4 months old AND can hold up head without help.

SUFFOCATION HAZARD

Babies have suffocated when seats tipped over on soft surfaces.

• NEVER use on a bed, sofa, cushion, or other soft surface.

Prevent Serious Injury or Death

• NEVER leave the child unattended.
• To avoid injury ensure that children are kept away when unfolding and folding this product.
• Do not let children play with this product.
• When using the USB cord, only use the one supplied with this swing.
• Check the USB cord and wall adaptor regularly for damage. Do not use if any damage has occurred.
• Use USB cord only with a 5 Volt/1 Amp (5 Watts) USB A wall adaptor.
• The product shall only be used with a transformer for toys.
• The transformer is not a toy.
• This product is only to be connected to equipment bearing either of the following symbols: ? (IEC symbol for Class II equipment)
• Do not use extension cords.

CAUTION

This product contains small parts. Adult assembly required.

IMPORTANT

• The provided USB cord is 183cm in length.
• Please read all instructions before assembly and use of the product.
• Care should be taken in unpacking and assembly.
• Examine product frequently for damaged, missing, or loose parts.
• DO NOT use if any parts are missing, damaged, or broken.
• Contact Kids2 for replacement parts and instructions if needed. Never substitute parts.
• This product does not replace a cot or a crib. Should the child fall asleep, then it should be placed in a suitable cot or crib.

Care and Cleaning

• Seat pad and headrest: Remove from frame. Fasten buckles on seat restraint and seat pad. Fasten all hook-and-loop patches to the corresponding patch. Machine wash with cold water, gentle cycle. No bleach. Tumble dry, low heat.
• Toy bar and toys: Wipe clean with a damp cloth and mild soap. Air dry. Do not immerse in water.
• Frame: Wipe the metal frame with soft, clean cloth and mild soap.
• Storage: When putting swing away for storage, always store in a dry location, away from any heat sources, and out of the sun.

Parts List

Assembly Instructions

The following steps describe how to assemble the Ingenuity SimpleComfort™ Compact Soothing Swing - Parker™.

Step 1: Assemble the Base

Attach the left leg assembly (1) and right leg assembly (2) to the bottom frame assembly (3). Ensure they click securely into place. Refer to the diagram for correct orientation.

Step 2: Attach the Seat Support

Connect the seat support arms (part of the bottom frame assembly) to the main frame. This may involve inserting pins or securing with screws. Refer to the diagram.

Step 3: Install the Control Module

Attach the control module assembly (4) to the swing arm assembly (5). This typically involves sliding or clicking the module into place.

Step 4: Connect the Swing Arm

Attach the swing arm assembly (5) to the main frame. Secure using M5 Philips head screws (A) and M5 nuts (B). Ensure all connections are tight.

Step 5: Attach Recline Mechanisms

Install the left recline mechanism (6) and right recline mechanism (7) into their respective slots on the swing arm. Ensure they are properly seated.

Step 6: Attach Footrest and Backrest Tubes

Connect the foot rest tube (8) and back rest tube (9) to the seat frame. These usually slide or clip into place.

Step 7: Install Seat Pad and Headrest

Place the seat pad (10) onto the seat frame. Attach the headrest (12) to the seat pad. Secure all buckles and hook-and-loop patches.

Step 8: Attach Toy Bar

Attach the toy bar with toys (11) to the designated points on the swing arm. It should click into place.

Step 9: Connect USB Cable

Connect the USB A Cable (13) to the control module. Ensure it is securely plugged in.

Step 10: Final Check

Review all connections to ensure they are secure. Check that all parts are correctly installed.

Using the Swing Control Module

The swing is operated by a control module located on the swing arm.

Controls:

• Power Switch: Touch to turn the Swing Control Module ON or OFF.
• Speed Selector Button and Indicator: Provides 6 speed settings and an OFF option. LEDs indicate the selected speed. Touch the button until the desired speed is displayed.
• Swing Timer Select Button and Indicator: Allows automatic shut-off. Touch to select timer settings of 15, 20, or 30 minutes. LEDs indicate the selected time. If no setting is selected, a default of 15 minutes is used.
• Nature Sounds/Music Button: Touch to begin playback of nature sounds and music. Touch again to select desired sounds or songs. Auto-shutoff occurs after approximately 20 minutes.
• Volume Control: Touch to adjust the volume for music and nature sounds, or to turn them off.

Operation:

• To start the swing function, touch the Power switch, then touch the Speed Selector button until the desired speed is shown on the LED indicator.
• When changing speed during motion, the LED bar graph will flash for five seconds.
• When the timer expires, the swing stops, and the Speed Selector and Timer LEDs turn OFF.
• To use the swing after auto-shutoff, press the Swing Timer Select button or the Speed Selector button.

Using the Seat Restraint

Ensure the seat restraint is properly adjusted for your baby's safety.

1. Thread the shoulder straps through the seat pad slots.
2. Buckle the shoulder straps and the waist strap together.
3. Adjust the straps to fit snugly around your baby.

Using the Recline Function

The seat can be reclined to different positions for your baby's comfort.

To adjust the recline, locate the recline lever or buttons on the side of the seat and move them to the desired position.

Rotation of the Seat

The seat can be rotated to face different directions.

To rotate the seat, press and hold the rotation release button and turn the seat to the desired position.

Disassembly

To disassemble the swing, reverse the assembly steps. Pay attention to any release buttons or locking mechanisms.

FCC Statement / CAN ICES-3 (B) / NMB-3(B)

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Déclaration FCC / CAN ICES-3 (B) / NMB-3(B)

Cet appareil est conforme à l'article 15 de la réglementation FCC. Son utilisation est sujette aux deux conditions suivantes : 1) ce dispositif ne peut causer d'interférences nuisibles, et 2) ce dispositif doit accepter toute interférence reçue, y compris les interférences pouvant causer un fonctionnement indésirable.

ATTENTION : Toute modification apportée à cet appareil, sans consentement explicite des responsables conformité, est susceptible d'annuler le droit d'usage de cet appareil.

REMARQUE : Cet article a été testé et déclaré conforme aux exigences requises pour les appareils numériques de classe B, conformément à l'article 15 de la réglementation FCC. Ces exigences visent à assurer une protection raisonnable contre les interférences nuisibles dans une installation chez des particuliers. Cet appareil génère, utilise et peut émettre de l'énergie radioélectrique, et s'il n'est pas installé et utilisé conformément aux instructions, il est susceptible de perturber les communications radio.

Nous ne pouvons garantir la non-interférence pour une installation donnée. Lorsque vous constatez que le matériel perturbe effectivement la réception radio ou télévision, vous pouvez vérifier ces interférences en éteignant et rallumant l'appareil. Dans ce cas, essayez une ou plusieurs des mesures suivantes :

• Réorientez ou déplacez l'antenne de réception.
• Éloignez l'appareil et le récepteur.
• Raccordez le matériel à une prise hors-circuit connexion de ce récepteur.
• Adressez-vous au fournisseur ou à un technicien expert en radio et télévision.