Ingenuity InLighten Soothing Swing - Van Elephant

IMPORTANT SAFETY INFORMATION

WARNING: FALL AND STRANGULATION HAZARDS:

• ALWAYS use the restraint system. Adjust to fit snugly.
• STOP using product when infant attempts to climb out (approximately 9 months).
• DO NOT use this product once your child can sit up unaided or weighs more than 9 kg / 20 lbs. DO NOT use this product if your child weighs less than 3 kg / 6 lbs.
• Stay near and watch baby during use. This product is not safe for sleep or unsupervised use. If baby falls asleep, remove baby as soon as possible and place baby on a firm, flat sleep surface such as a crib or bassinet.
• Never let the child sleep in this product.
• DO NOT move or lift this product with the baby inside it. Never lift product using a toy bar as a handle.
• ALWAYS place product on floor. NEVER use this product on an elevated surface (e.g. a table).
• NEVER attach any additional strings or straps to product or toy bar.

SUFFOCATION HAZARD:

• ALWAYS keep swing seat fully reclined until infant is at least 4 months old AND can hold up head without help.
• NEVER use on a bed, sofa, cushion, or other soft surface.

Prevent Serious Injury or Death:

• NEVER leave the child unattended.
• To avoid injury ensure that children are kept away when unfolding and folding this product.
• Do not let children play with this product.
• When using the USB cord, only use the one supplied with this swing.
• Check the USB cord and wall adaptor regularly for damage. Do not use if any damage has occurred.
• Use USB cord only with a 5 Volt/1 Amp (5 Watts) USB A wall adaptor.
• The product shall only be used with a transformer for toys.
• The transformer is not a toy.
• This product is only to be connected to equipment bearing either of the following symbols: [electrical symbol]
• Do not use extension cords.
• NEVER use as an infant carrier for automobile or airline travel.

CAUTION:

• This product contains small parts. Adult assembly required.

IMPORTANT NOTES

• The provided USB cord is 183 cm in length.
• Please read all instructions before assembly and use of the product.
• Care should be taken in unpacking and assembly.
• Examine product frequently for damaged, missing, or loose parts.
• DO NOT use if any parts are missing, damaged, or broken.
• Contact Kids2 for replacement parts and instructions if needed. Never substitute parts.
• This product does not replace a cot or a crib. Should the child fall asleep, then it should be placed in a suitable cot or crib.

Care and Cleaning

• Seat pad: Remove from frame. Fasten buckles on seat restraint and seat pad. Fasten all hook-and-loop patches to the corresponding patch. Machine wash with cold water, gentle cycle. No bleach. Tumble dry, using low heat.
• Bolster: Machine wash with cold water, gentle cycle. No bleach. Air dry flat.
• Toys: Wipe clean with a damp cloth and mild soap. Air dry. Do not immerse in water.
• Frame: Wipe the metal frame with a soft, clean cloth and mild soap.
• Storage: When putting swing away for storage, always store in a dry location, away from any heat sources, and out of the sun.

Parts List

Assembly Instructions

Follow the numbered steps to assemble the swing. Ensure all parts are securely fastened.

1. Attach the left leg tube (2) and left front foot (3) to the swing head assembly (1).
2. Attach the right leg tube (4) and right front foot (5) to the swing head assembly (1).
3. Attach the swing arm assembly (6) to the frame using screws (A) and nuts (B).
4. Attach the cross brace assembly (7) to the frame.
5. Attach the right recline (8) and left recline (9) to the footrest tube (10) and back rest tube (11).
6. Connect the swing arm assembly (6) to the main frame.
7. Attach the seat pad (12) to the frame, securing the buckles and hook-and-loop patches.
8. Prepare the seat for use by orienting it correctly.
9. Attach the recline components to the frame.
10. Attach the seat pad (12) to the seat frame.
11. Secure the seat restraint system.
12. Attach the mobile with toys (13) to the top of the swing.
13. Connect the USB cable (14) to the power module and the swing frame.
14. Attach the bolster (15) to the seat.
15. Attach the toys (elephant) (16) and (rainbow) (17) to the mobile.

Using the Swing Control Module

Touch the Power switch [power-symbol] to power the Swing Control Module.

• Speed Selector: Provides 5 speed settings and OFF. LEDs indicate the selected speed. Touch the button until the desired setting is displayed.
• Swing Timer: Allows automatic shut-off. Touch the button to select 30, 60, or 90 minutes. If no timer is selected, it defaults to 30 minutes.
• Nature Sounds/Music: Touch to play music and nature sounds. Auto-shutoff occurs after approximately 30 minutes.
• Volume Control: Touch to adjust or turn off the volume for music and nature sounds.
• Mobile Illumination: Press to start the mobile and switch on the lights. Press again for a random light/play pattern.

Using the Seat Restraint

Follow the diagrams to properly secure the baby in the seat restraint system.

Using the Recline Function

Refer to the diagrams for instructions on how to adjust the recline of the seat.

Rotation of the Seat

Follow the diagrams to rotate the seat.

Storage and Travel

Follow the diagrams for instructions on how to fold the swing for storage or travel.

FCC Statement / CAN ICES-3 (B) / NMB-3(B)

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.