UGREEN NASync DXP8800 Plus

製品概要 (Product Overview)

The DXP8800 Plus is a network-attached storage device designed for individual users, home offices, studios, and small businesses. This device functions as an intelligent data management center, allowing users to store and access data from any device, anywhere, via network access. It features multimedia applications for enjoying photos, music, and videos, enabling easy data access, sharing, and synchronization across devices. It also supports seamless collaboration and productivity tools. With high-speed dual 10 Gigabit Ethernet ports and a PCIe expansion slot, application performance and system functionality are enhanced. Its scalable design allows for storage capacity expansion according to needs. Offering top-level security, high performance, and easy expansion, this device provides a next-generation data management experience.

ご使用前にお読みください (Please Read Before Use)

• To ensure efficient data transmission, it is recommended to use a router or switch with 10 Gigabit or higher LAN ports and the included Ethernet cable (CAT7 or higher) to connect the NAS.
• We recommend using new hard drives. When you install a drive, the NAS system will format the drive, erasing all existing data. Please back up important data before installation.
• Only use the genuine power cable that meets the power specifications of this device, or a safety-certified power cable.
• Do not insert or remove hard drives while the NAS device is powered on. To prevent potential data loss, corruption, or drive damage, please turn off the device using the app first.
• Only update firmware when there is a stable power supply. Do not turn off the power during the update process.
• Unbinding the device will erase all data and make it unrecoverable. Ensure your data is properly backed up before unbinding the device.

同梱物 (Package Contents)

• Network Attached Storage x1 (Image of the NAS unit)
• Instruction Manual x1 (Image of a booklet)
• Warranty Card x1 (Image of a card)
• Hard Drive Tray Key x2 (Image of two small keys)
• Power Cable x1 (Image of a power cable)
• Ethernet Cable (CAT7) x2 (Image of two Ethernet cables)
• SSD Silicone Pad (for heat dissipation) x2 (Image of two small silicone pads)
• Screws and Screwdriver (Image of screws and a screwdriver)

製品概要 (Product Overview - Components)

Front Panel:

The front panel features drive bays labeled 01 through 08. It also includes a safety lock, a power button, a power indicator LED, a network indicator LED, and individual hard drive indicators for each bay.

External ports include:

• USB Type-A (3.2 Gen 2) Port
• Thunderbolt 4 Ports x2
• SD Card Slot

Rear Panel:

The rear panel includes:

• Magnetic Dust Mesh Filter
• PCIe Expansion Slot
• HDMI Port
• USB Type-A (3.2 Gen 2) Port
• USB Type-A (2.0) Ports x2
• 10GbE Ethernet Ports x2
• Power Port
• Reset Hole

Bottom Panel:

The bottom panel provides access to:

• M.2 Slots x2 (Optional)
• Memory Slots x2 (One memory module is pre-installed)

Warning [warning symbol]: Turn off the system power completely before inserting or removing hard drives (including M.2 SSDs) or memory modules. Properly shut down the NAS and disconnect it from the power source.

3.5インチハードドライブの取り付け (3.5-inch Hard Drive Installation)

ハードドライブトレイのロック解除 (Hard Drive Tray Lock Release)

Use the provided key to unlock the hard drive tray. Press the buckle, release the handle, and pull out the tray.

• Step a: Insert the key into the lock and turn to unlock.
• Step b: Press the release button/buckle.
• Step c: Pull the handle to release the tray.

3.5インチハードドライブの取り付け (3.5-inch Hard Drive Installation - Screwdriver not required)

1. Tray Preparation: Flip the hard drive tray over.
2. Clamp Arm Release: Press the button marked 'Press' and gently pull the clamp arm outwards.
3. Drive Placement: Place the hard drive into the tray, ensuring the tray's fixing pins align with the hard drive's screw holes. The drive's pins should be facing downwards.
4. Drive Securing: Push the clamp arm back to its original position to secure the drive in the tray.
5. Tray Insertion: Insert the filled drive tray into the empty drive bay and secure it.

2.5インチハードドライブの取り付け (2.5-inch Hard Drive Installation)

2.5インチハードドライブの取り付け (Screwdriver required)

1. Pin Adjustment: Use the hard drive tray key to remove the end fixed pin. Attach this pin to the fixing hole located near the tray cover. (If you later switch back to a 3.5-inch hard drive, you can move this pin back to the end position.)
2. Drive Placement: Place the 2.5-inch hard drive in the tray, aligning its screw holes with the four corresponding holes on the tray. The drive's pins should be facing downwards.
3. Drive Securing: Flip the tray over. Secure the drive in place by tightening the included screws through the tray and into the drive.
4. Tray Insertion: Insert the drive tray into the empty drive bay and secure it.

Note: If replacing with a 3.5-inch hard drive, remember to move the fixed pins back to the end position.

M.2 SSDの取り付け (M.2 SSD Installation)

Installing an M.2 SSD allows it to be used either as a regular storage drive or as a read/write cache to enhance random data read/write performance.

1. Preparation: Turn off the NAS device and turn it over. Loosen the screws and remove the bottom panel.
2. Loosen Fixing Screw: Loosen the M.2 fixing screw.
3. SSD Insertion: Insert the M.2 SSD into the slot at the angle shown. Secure the SSD by tightening the fixing screw.
4. Pad Attachment: Peel off the protective film from a silicone pad and attach it to the front of the SSD. Peel off the remaining protective film from the other side of the pad.
5. Reassembly and Setup: Reattach the bottom panel and tighten the screws. Turn on the NAS. Once the system boots successfully, set up the SSD cache using the 'UGREEN NAS' application.

Warning [warning symbol]: To avoid data loss, please remove the SSD cache in the 'UGREEN NAS' app before removing the M.2 SSD. This enhances protection when the system is using the cache.

メモリモジュールの取り付け (Memory Module Installation)

1. Preparation: Turn off the NAS device and turn it over. Loosen the screws and remove the bottom panel.
2. Module Insertion: Align the notch on the memory module's pins with the corresponding ridge in the slot. Insert the module into the slot and gently push down until it is securely seated.
3. Reassembly: Reattach the bottom panel and tighten the screws.

PCIe拡張カードの取り付け (PCIe Expansion Card Installation)

1. Initial Preparation: Turn off the NAS, disconnect it from the power source, and remove all hard drive trays from the drive bays.
2. Accessing Internals: Turn the NAS over. Remove the screws and the bottom panel. Then, loosen the fixing screws located at the corners of the bottom to remove the device's feet.
3. Rear Cover Removal: Remove the screws that secure the ventilation cover on the back of the device.
4. Outer Shell Removal: Remove the internal fixing screws that attach the outer shell to the internal frame. Lift the outer shell to remove it from the device.
5. Bracket Removal: Remove the screws holding the existing bracket in place. Remove the bracket itself and store it safely in case you need to replace the PCIe expansion card later.
6. Card Installation: Insert the new PCIe expansion card into the appropriate slot. Ensure the card is securely connected and then tighten the screws to fix it in place.
7. Reassembly: Reattach the outer shell to the device, securing it with the internal fixing screws. Next, attach the bottom panel and tighten the screws at the bottom corners. Finally, replace the feet.

Tips: Before attaching the bottom panel, check if the internal springs are in their correct positions. If not, manually return them to the correct position.

電源の入れ方 (How to Power On)

Connect the NAS to your router's LAN port using an Ethernet cable. Connect the power adapter to the device. Briefly press the power button to turn the NAS on.

Tips: After powering on, download the 'UGREEN NAS' application. Navigate to 'Control Panel' > 'Hardware & Power' to configure automatic power-on after a power failure.

Warning [warning symbol]: The power cord must be connected to an earthed outlet.

インジケータとブザー (Indicators and Buzzer)

LED Indicators:

Buzzer:

製品仕様 (Product Specifications)

ご注意・警告 (Precautions and Warnings)

Precautions:

• Install the NAS device according to the diagrams in this manual. Do not turn the device upside down or place it in an unstable position while operating.
• Place the NAS in an environment with stable temperature and low humidity. Avoid direct sunlight and liquids.
• In case of thunderstorms or unstable voltage, turn off the device's power to avoid potential damage.
• Keep the device away from heat sources and humid environments to reduce the risk of fire or electric shock.
• Do not insert foreign objects into the NAS to avoid damage from misuse or short circuits.
• When cleaning, turn off the NAS device's power beforehand. Use a soft, damp cloth for cleaning. Do not use chemical cleaners or spray cleaners.
• Do not drop, crush, apply strong impact, or throw the NAS.
• This product contains small parts. Keep out of reach of children to prevent accidental ingestion and choking.
• Do not disassemble or repair the NAS device yourself. Improper disassembly and assembly may cause electric shock or other safety hazards. For repairs or replacement parts, contact UGREEN customer service.

Warnings:

• This product contains a lithium-manganese dioxide battery. Do not disassemble, strike, crush, or incinerate it.
• Do not place the product in high-temperature environments. Keep out of reach of children.
• If a battery is swallowed or enters the body, seek immediate medical attention.
• If you notice any abnormality with the battery, replace it as it may indicate low power. Ensure correct polarity when replacing the battery.
• If the battery leaks, do not let the leaked liquid come into contact with skin or eyes. If contact occurs, wash immediately with water and seek medical attention as soon as possible.
• When disposing of batteries, keep them away from children and follow local regulations for disposal.
• The included AC power cable is specific to this electrical appliance and cannot be used with other electrical appliances.
• Keep out of reach of children [icon of child with line through it].